Xinysun Instrument (Shanghai) Co., Ltd.

Solutions

Breadcrumb: Home > Solutions > Fluorescent Inspection

ASTM E3022-26 FAQs: 12 Common Questions Explained

Updated:2026-11-17Views:

12 common questions about ASTM E3022-26, answered briefly: what the standard covers (the scope is limited to UV-A LED lamps, so mercury lamps and gas discharge lamps fall outside it), how it differs from the earlier E3022-15 revision, how the type test report and the unit test report are used, which compliance claims are misleading, what a UV radiometer has to meet, and the safety points to observe. It is written for a quick check before a purchase or a NADCAP audit, and it also lists the documents to request, explains why a retrofitted LED lamp cannot be called compliant, and gives the spot size and irradiance figures that apply to type A, B and C sources.

1. The standard itself

What is the ASTM E3022-26 standard?

ASTM E3022-26 is the international standard for UV-A LED black lights used in fluorescent magnetic particle inspection (MPI) and fluorescent penetrant inspection (FPI). It specifies the performance, test methods and reporting requirements for UV-A LED sources, and it is widely cited in aerospace NADCAP audits.

Note the scope carefully: the standard's scope is limited to UV-A LED lamps. Mercury lamps, gas discharge lamps and borescope light sources are outside its coverage.

Are certificates to ASTM E3022-26 interchangeable with older E3022-15 / E3022-18 certificates?

They can still be used, and there is no mandatory switch to new certificates. The revisions involve just a small number of wording changes and an adjustment to the spectral test range, and they do not affect the validity of lamps that are already certified.

Which body regulates and audits ASTM E3022-26?

There is no independent third-party regulator; all testing and certification work is carried out by the light source manufacturer itself. NADCAP and ISO auditors sample the clauses of the standard, and ASTM E3022-26 is also referenced by ASTM E1444 (magnetic particle testing) and ASTM E1417 (penetrant testing).

Because there is no external enforcement, choosing a manufacturer with a complete laboratory capability and verifying the reports yourself is more reliable than reading advertising claims. Ask to visit the manufacturer's test laboratory during the purchasing stage.

2. Two reports: type test and unit test

What is the difference between a type test report and a unit test report, and does an audit need both?

The two reports serve different purposes, and a NADCAP audit may ask for either. The type test report verifies that the design of the model itself meets the standard, covering the full set of items: temperature stability, emission spectrum, filter transmittance and current ripple. The unit test report proves that the individual lamp you received meets the specification. You should be able to supply both.

Report typeTest objectPurposeHow it is obtained
Type test reportBaseline reference source for the product modelVerifies that the model design meets the standard, covering temperature stability, emission spectrum, filter transmittance, current ripple, battery discharge and other itemsCustomers may request it from the manufacturer for review
Unit test reportEvery lamp shippedProves that the source you received meets the specification; items include peak irradiance, full width at half maximum, emission spectrum and peak wavelengthDelivered with the lamp

Why test each unit when a type test already exists? Because even within one model, every LED device varies from the next. Without unit verification there is no way to ensure that the wavelength and irradiance of each lamp delivered fall inside the accepted range.

What documents must I request when buying a black light rated to ASTM E3022-26?

Ask the manufacturer for three documents: the type test report, the unit test report for the specific lamp, and the product conformity certificate. You can also ask to visit the manufacturer's test laboratory to confirm that the claimed test capability actually exists.

Can a lost unit test report or certificate be reissued?

A reputable light source manufacturer keeps the original test data, and you can contact them to request a replacement certificate. File the electronic copies with the equipment records at the time of purchase, so that the basis is not lost when staff or suppliers change.

3. False compliance claims and recertification after repair

Can a mercury lamp retrofitted with an LED replacement bulb be described as compliant with ASTM E3022-26?

No. The standard requires testing of the complete lamp as one integrated unit: housing, filter, circuit, thermal path and power supply must all be evaluated together. Replacing just the LED device, without verification of the complete lamp, is a misleading claim.

Integrated testing is a hard requirement because the thermal design directly determines the irradiance decay and wavelength shift that occur during operation. The standard requires that irradiance decay after continuous operation stay within 20% and that the peak wavelength stay at or below 370 nm, and these figures cannot be measured without the whole lamp running.

Which repairs to a UV-A black light require new ASTM E3022-26 certification?

Replacing core components that affect optical output (the LED device or the driver board) must be recertified by the original manufacturer or its service partner. Replacing just non-optical parts such as an external power adapter, power cord or battery does not require recertification.

Users should not replace optical core components themselves, because the certification then becomes invalid. Frequent LED failure is usually not normal behavior but a sign of a weakness in the thermal or driver design, which is worth turning into a question about the equipment design itself.

4. Measurement and acceptance

What are the mandatory requirements for a UV radiometer used to measure UV irradiance?

ASTM E3022-26 sets four requirements for UV-A radiometers: the calibration system, the probe aperture, the spectral response and the reading deviation. An oversized probe aperture introduces an additional measurement error of 8%-10%.

ItemRequirement
Calibration systemCalibrated under ISO 17025 / ISO 10012 or an equivalent system
Sensor probe apertureDiameter ≤12.7 mm (0.5 in)
Spectral responseCentered near 365 nm, with a Gaussian bell-shaped or flat-top response
Audit criterionNADCAP requires the reading deviation to stay within ±5%

An oversized probe introduces an additional measurement error of 8%-10%, which directly produces an audit nonconformity. A UV radiometer can be used to keep a periodic re-verification log.

On a multi-LED integrated black light, a failed LED cannot be seen by eye - how do I troubleshoot?

Under the filter you cannot identify a failed LED by eye; even with one device dark, the overall pattern still looks "normal". The correct approach is to measure UV irradiance at regular intervals: a clear drop in irradiance identifies a fault in the source.

In practice, fix the measurement position and distance (for example, always at the center of the spot at 150 mm) and record each reading in a log. A single reading means little; the trend is the criterion.

How does ASTM E3022-26 classify spot requirements for different types of UV-A LED source?

The standard divides sources by power supply into types A, B and C. All three require irradiance of at least 1000 μW/cm² within the effective spot; they differ in spot diameter: type A (AC) and type B (battery portable) are 5 in (127 mm), and type C (flashlight) is 3 in (76 mm).

CategoryPower supplySpot requirement
Type AAC poweredIrradiance ≥1000 μW/cm² within a 5 in (127 mm) spot
Type BBattery portableIrradiance ≥1000 μW/cm² within a 5 in (127 mm) spot
Type CFlashlight, single LEDIrradiance ≥1000 μW/cm² within a 3 in (76 mm) spot

When selecting, start by establishing which type you need. Fixed stations doing large-area scanning usually use a type A or B area source, such as the LUYOR-BB series UV inspection lamp; single-point positioning in confined spaces uses a type C flashlight, such as the LUYOR-3180. The spot figure describes effective coverage, not peak brightness, so do not apply the center intensity instead.

5. Safety in use

What safety precautions apply when using UV-A black lights?

UV-A radiation can damage the eyes and skin, so protection is required during work. Sources sold into European and North American markets need to meet the IEC 62471 photobiological safety standard. Even though UV-A carries lower risk than UV-B or UV-C, long continuous inspection still calls for protective eyewear and gloves and for avoiding direct skin exposure.

The test environment is also constrained: the standard requires ambient light below 21.5 lux and an ambient temperature held at 25±3 ℃, otherwise readings are disturbed by ambient light and run high.

6. Where to read a more detailed explanation

The 12 questions above cover the scope of the standard, the report system, how to recognize false compliance claims, instrument requirements and safety. If you want the test logic behind each clause, the detailed workflow for integrated lamp verification, and the questions NADCAP auditors commonly ask, see our in-depth guide to ASTM E3022-26.

To select a UV-A LED black light to the standard, browse the 365 nm black light section and compare types A, B and C against your spot requirement.

Related sections and models

This article belongs to the FAQ section.

Other sections on the same product line include 365 nm black lights (UV area sources for inspection, leak detection and fluorescence checks - look at irradiance, not wattage) and UV radiometers (measuring mW/cm² intensity and J/cm² accumulated energy, which is what a compliance call depends on), plus life science instruments (the entry point for fluorescence imaging, UV crosslinking, UV transmission and cell irradiation).

Models mentioned in this article: LUYOR-3103, LUYOR-BBMA, LUYOR-365L. Ranges, accuracy and accessory lists for each model are given on the product pages.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top