Xinysun Instrument (Shanghai) Co., Ltd.

Solutions

Breadcrumb: Home > Solutions > Biofilm Detection

LUYOR-339 Biofilm Detection Light: 10 FAQs (LUYOR Authorized Distributor)

Updated:2026-11-17Views:

10 common questions about the LUYOR-339 handheld biofilm detection lamp: how the fluorescence detection works, how green and blue fluorescence are told apart, whether dormant bacteria and VBNC cells can be detected, which surfaces and industries the lamp suits, how it divides the work with ATP swabs and laboratory culture, runtime and operating points, and how to keep evidence for an audit. General selection questions are handled on a separate page; this page concentrates on the field details of one model, including the surfaces to treat with care, the training a team needs before routine inspection, and what its images can and cannot prove.

Xinyisheng Instruments (Shanghai) Co., Ltd. This page collects 10 common questions about the handheld biofilm detection lamp LUYOR-339: the detection principle, green/blue fluorescence discrimination, detection of dormant and VBNC bacteria, suitable surfaces and industries, the division of work with ATP swabs and laboratory culture, runtime and operating points, and audit documentation. General selection questions are covered separately in ten frequent questions on biofilm detection lamps.

What kind of device is the LUYOR-339?

The LUYOR-339 is a handheld, cordless, battery-powered biofilm detection lamp, a non-contact fluorescence detection device. It emits long-wave ultraviolet (UVA) onto the surface being inspected, so biofilm and bacterial contamination that the eye cannot see appear directly as fluorescence, and staff on site can tell within seconds which points are affected and how the contamination is distributed. It is the higher-power model in the LUYOR biofilm detection range, with wider irradiation coverage, and it suits rapid screening of large surfaces and whole-area inspection rounds.

How does it detect bacteria and biofilm?

When the UVA from the lamp head reaches a surface, organic components such as extracellular protein in the contamination fluoresce and stand out against a clean surface in a way the eye can distinguish. The detection basis is whether protein residue is present, not whether a microorganism will grow on a culture medium, so it also works on dormant bacteria, stressed bacteria and microorganisms in the VBNC (viable but non-culturable) state. That is a key difference from plate culture.

What do green fluorescence and blue fluorescence each mean?

This is a practical capability of the LUYOR-339 that is easily overlooked: under UVA it distinguishes contamination by color, so staff on site can decide on the spot which cleaning procedure to follow.

Fluorescence colorWhat it indicatesHow to handle it
Green fluorescenceContamination containing extracellular protein - biofilm, active bacteriaIf it remains after wiping, treat the point as contaminated, run the cleaning procedure and confirm by ATP or laboratory testing where needed
Blue fluorescenceInanimate material such as dust and fibersRemoved by routine wiping; not a microbial contamination risk

The value of this discrimination is that it avoids two kinds of misjudgment: a layer of floating dust is not mistaken for microbial contamination and does not trigger a shutdown and deep clean, and a real biofilm is not dismissed as "a bit of dirt on the surface" and simply wiped over. Where evidence has to be kept, the green fluorescence in a photograph is itself direct visual evidence that contamination is present.

In which industries and sites can it be used?

It covers five settings - food and beverage, pharmaceutical and biotechnology, medical and dental, pre-startup checks after a shutdown or product changeover, and hygiene audits - each with different points of concern:

  • Food, beverage and dairy processing: hygiene verification of equipment and pipe surfaces after CIP / COP, with key areas including tank walls, pipe joints, valves, gaskets, conveyors and filling heads;

  • Pharmaceutical and biotechnology plants: cleaning validation of production equipment and the environment, such as solution tanks, pipe connections and return-air grilles of laminar flow hoods;

  • Medical and dental facilities: cross-contamination checks at aseptic points such as instrument lumens, tray corners, treatment tables and the interior of washer-disinfectors;

  • Pre-startup checks after a shutdown or changeover: confirming clean status before production resumes, to avoid batch deviations;

  • Hygiene audits and quality control: commercial kitchens, hotels, breweries, cleanrooms, water treatment and cooling towers, research laboratories and similar.

Which surfaces can be inspected? Are there any restrictions?

It suits most surfaces that are not mirror-like: metal, plastic, ceramic, rubber gaskets and organic materials. Highly reflective or glossy surfaces (for example a polished stainless steel angle that throws light back) can interfere with reading, and adjusting the irradiation or viewing angle usually improves it. Two preconditions apply: dim the ambient light on site to raise fluorescence contrast, and make sure the surface is dry, because a residual water film produces reflection.

Can it replace laboratory testing?

No, and it should not be used that way. The LUYOR-339 is positioned as a rapid screening and inspection tool: it answers where contamination is and where sampling points should be placed, and it gives an on-site presence/absence judgment without quantifying or identifying organisms. Species identification and colony counting remain laboratory work. A sensible division is: lamp for full-coverage screening, then mark the points, then ATP sampling or laboratory confirmation. Consumables are then spent where there is a real problem, which is better for both speed and cost. One more point: a negative culture does not prove the site is clean, and a lamp check can locate the risk points before the culture report arrives.

What are the advantages over traditional detection methods?

What it replaces is blind spot sampling, not testing itself. Sweeping a whole surface, getting a result on site and needing no reagents or consumables are the main differences from swab sampling and plate culture; the price is that it gives no number and does not identify organisms. The comparison, item by item:

ItemLUYOR-339 fluorescence inspectionConventional swab sampling / plate culture
CoverageWhole-surface sweep, not samplingSampling at selected points, easy to miss areas
Time to resultVisible on site immediatelyCulture usually takes several days
Consumable costNo reagents, no consumablesOne swab per point, an ongoing expense
Effect on the surfaceNon-contact, does not disturb the surfaceContact sampling
Blind spotsCannot quantify, does not identify organismsReflects the sampled point alone; dormant / VBNC cells may be missed
Does using it require training?

The operation itself is simple: dim the ambient light, sweep at a steady pace along the planned route, judge green against blue, mark and photograph. It is worth having the team establish a short baseline before routine inspection starts: illuminate a known clean surface and a known contaminated surface once each, fix the ambient light conditions used for the work, and agree on the reading criteria. Only then are results from the same team comparable across batches. The protective glasses and carry case supplied with the lamp make moves between areas and long sessions easier, and a runtime of about 5 hours is enough to walk one production line or one clean zone in a single pass.

What are the runtime and durability like?

The LUYOR-339 runs on a cordless battery with about 5 hours of continuous operation, and the internal cooling design allows long continuous use without overheating. The housing is built for industrial use and suits the frequent handling and moving of food, beverage, pharmaceutical and medical sites. Routine care is mainly keeping the lamp head clean and charging on a schedule; switch the unit off and disconnect power before cleaning or servicing it.

Can it be used during an audit?

Yes, and that is one of its common uses. A fluorescence image is direct visual evidence that contamination is present, and photographs of green fluorescent points taken during an inspection can go into the cleaning validation file as supporting material for hygiene management, compliance review and the quality system. For companies working under HACCP or GMP that need to show cleaning validation does not rest on sampling alone, adding fluorescence inspection to the daily SOP is a low-cost improvement.


For an on-site demonstration or selection advice, see the full range in the biofilm detection lamp section (LUYOR-339 / LUYOR-330 / XEPU-1720), or contact us directly. The portable LUYOR-330 fills the gap in narrow spaces such as pipe interiors, and pairing it with the 339 by area is a common arrangement.

Related sections and models

This article belongs to the FAQ section.

Other sections on the same product line include biofilm detection lamps (UV-A excited biofilm autofluorescence, which makes contamination the eye cannot see visible) and industrial test instruments (the entry point for four lines: UV inspection, tachometry, stroboscopic observation and surface inspection).

Models mentioned in this article: LUYOR-330, XEPU-1720. Ranges, accuracy and accessory lists for each model are given on the product pages.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top