Xinysun Instrument (Shanghai) Co., Ltd.

Solutions

Breadcrumb: Home > Solutions > Biofilm Detection

Vanillin Rapid Test Strips: 365nm Fluorescence Reading with LELMS-38L

Updated:2026-11-08Views:

This article unpacks a 2026 Biosensors study on rapid vanillin detection. It explains how gold nanoparticle and fluorescent microsphere lateral flow strips divide the work, why a probe excited at 360 nm and emitting at 610 nm corresponds to the 365 nm channel of the LELMS-38L, and where the boundary lies: the handheld UV lamp is responsible for nothing more than making the T and C lines visible, while quantitation is left to a fluorescence reader. Two formats are compared side by side on sensitivity, linear range and stability, and the reading grades and sample preparation parameters are set out in full.

On 4 November 2026, Biosensors published a paper from the Institute of Tobacco Research, Chinese Academy of Agricultural Sciences (Laboratory of Tobacco Quality and Safety Risk Assessment, Ministry of Agriculture and Rural Affairs), the School of the Environment and Safety Engineering at Jiangsu University, and Yizhong (Qingdao) Industrial Co., Ltd.: Hou P et al., Development and Application of Two Modes of Immunochromatographic Assay Strips for Vanillin Rapid Detection in Food Products, Biosensors 2026, 16, 630, doi:10.3390/bios16110630 (CC BY). The work produced two kinds of vanillin immunochromatographic strip, and for the fluorescent microsphere FICA strip the methods section states explicitly that a LELMS-38L handheld three-wavelength UV lamp was used for visualization and reading.

1. Rapid vanillin testing is held up by the word "on site"

Vanillin (4-hydroxy-3-methoxybenzaldehyde) is a food flavoring produced on a very large scale and common in beverages, chocolate and dairy products. Statistics cited in the paper put world annual consumption at about 20,000 tonnes in 2019, with China producing roughly seventy percent. Long-term excessive intake may bring headache, nausea, load on the liver and kidneys and taste dependency, and infants are more sensitive, so the permitted range and dosage are explicitly constrained: GB 2760-2024 sets an upper limit of 50 mg/kg for vanillin in complementary foods for infants and young children, and forbids its addition to formulas for infants aged 0-6 months; JECFA gives an acceptable daily intake of 0-10 mg/kg body weight.

The conventional means of confirmation are chromatography and immunoassay. Among the established methods the paper lists, HPLC measured vanillin in bee pollen at 700-2300 ng/g, UPLC in edible oil at 130-890 ng/g (detection limit 30 ng/g), and HPLC-MS/MS in functional drinks at 20358-34423 ng/mL (detection limit 15 ng/mL). These methods are sensitive and accurate, but they need instruments, sample preparation and trained staff. The time comparison given in the paper is: about 30 minutes for chromatography, about 150 minutes for a conventional multi-step ELISA, while a strip compresses the whole process into 10 minutes and lets you read the result directly.

That is the place of the immunochromatographic assay (ICA) strip: it does not produce a confirmatory report, it performs on-site screening. In regulatory sampling, raw material intake and production line self-checks, what is needed is to pick out the suspect samples before anything else and then concentrate limited confirmatory capacity on a small number of them.

2. One colorimetric, one fluorescent: how the two readouts divide the work

The study used the same anti-vanillin monoclonal antibody, conjugated to two kinds of label, to make two strips. Both are competitive assays: the more vanillin in the sample, the less labeled probe is captured at the T line and the weaker the signal, while the C line should appear regardless of the sample and serves to show that the chromatographic run worked.

Item GICA colloidal gold strip FICA fluorescent microsphere strip
Label In-house gold nanoparticles, mean diameter 21.3 nm, probe absorption peak 525 nm Carboxylated fluorescent microspheres, mean diameter 210.5 nm
Readout signal Red T line, read by eye Fluorescent T line, excitation 360 nm, emission 610 nm
Viewing method Visual reading in daylight Viewed under a UV lamp; the paper used the LELMS-38L three-wavelength UV lamp
Visual semi-quantitative detection limit 15.6 ng/mL 3.12 ng/mL
Instrumental quantitative detection limit 10.3 ng/mL 2.04 ng/mL
Quantitative linear range 15.6-500 ng/mL (R² = 0.9933) 3.12-200 ng/mL (R² = 0.9945)
Quantitative instrument HG-1721 colloidal gold reader CYS-YG fluorescence reader

The gain from fluorescent microspheres is direct: the quantitative detection limit of FICA is 2.04 ng/mL, about five times better than the 10.3 ng/mL of GICA. The paper attributes this to the high fluorescence intensity, narrow emission peak and good photostability of the FMP probe, which make the T/C ratio respond more steeply to concentration change (FICA standard curve slope -1.5064, GICA -0.5707). Put another way, a similar step in concentration is easier to resolve in the fluorescence channel.

One further difference is stated plainly in the paper: observation of the fluorescent signal requires an excitation source. A GICA strip can be read in the hand, but to see how much fluorescence remains at the T line of a FICA strip you need a UV lamp whose output wavelength matches, and that is why the LELMS-38L appears in this paper.

3. Which step the LELMS-38L covers in this paper

The paper cites the instrument in two places. The equipment section states: The FICA strips were initially visualized and interpreted under a Three-Wavelength UV Lamp LELMS-38L (Luyor Instrument Co., Ltd., Shanghai, China); and the reading method section states: the FICA strips were visualized under a Three-Wavelength UV Lamp LELMS 38L. In other words, the lamp was used for visualization and initial reading of the FICA strips once color had developed - turning a fluorescent T line that the eye cannot see into a visible band that can be graded, not for measuring concentration.

A note on the waveband

The paper records the lamp model but does not state which channel was used, nor the irradiation distance, duration or viewing angle. The probe spectrum given in the text is excitation at 360 nm and emission at 610 nm. On that excitation wavelength, the channel that matches the probe is the 365 nm long-wave UV one; this correspondence is an interpretation based on the spectrum, not a conclusion of the paper. The irradiation conditions and lamp specifications set out below are product-side information, for reference when reproducing the work, and should not be written up as the method of the paper.

Product-side specifications: the LELMS-38L handheld three-wavelength UV lamp houses three 8 W tubes at 254 nm, 302 nm and 365 nm in a metal housing of 330 × 100 × 80 mm, with three rocker switches at the rear each controlling one channel, usable singly or together; center intensity at 10 cm is 1170, 848 and 1236 μW/cm² respectively (in the order 254 / 302 / 365 nm). The aperture carries a black UV filter of about 20 × 6 cm that suppresses visible light, so the background is darker when reading fluorescence; an aluminum alloy orange-peel reflector inside returns light from the back of the tubes to the aperture, making the central spot more uniform. It runs on 220 V (a 110 V version is also available) with a 2.5 m power cord, comes with fully transparent UV protective glasses as standard, and can be fitted to a benchtop stand where long fixed viewing is needed.

Do not treat the lamp as a detector. The quantitative results in the paper come from T/C values measured by a reader and then converted through a standard curve; the LELMS-38L provides excitation and viewing, nothing more. Being able to see a fluorescent band does not mean you can report the figure of 2.04 ng/mL. Writing "the vanillin content was measured with a UV lamp" is wrong; the correct statement is "semi-quantitative reading of the fluorescent strip was carried out under a UV lamp".

4. From loading to reading: the operating sequence for the fluorescence channel

The procedure in the methods section is fairly complete, and following this order keeps fluorescence reading stable.

1
Sample preparation

Spike negative samples (functional drinks, formula milk powder) and hold at room temperature for 2 h to reach adsorption equilibrium; extract with 10 mL of methanol/water 1:1, vortex for 1 min, sonicate for 10 min, centrifuge at 4000 r/min for 10 min; then dilute the supernatant 10-fold with working buffer to reduce matrix effects.

2
Loading and chromatography

Apply 70 μL of test solution to the sample pad (working buffer containing 10 mmol/L PBS and 5% methanol) and let it run at room temperature for 7 min. The T and C lines are sprayed in parallel on the NC membrane 5.0 mm apart, and the strip is cut 4.0 mm wide.

3
UV viewing

Switch on the 365 nm channel alone, and view the FICA strip in a darkened or light-shielded setting; angle the lamp, keep the eyes out of the direct beam and wear UV protective glasses. The black filter suppresses the visible component of the excitation light, so the 610 nm orange-red emission separates more easily from the background.

4
Grading and confirmation

Grade as negative, weak positive, positive or invalid according to the presence and strength of the T and C lines; where a numerical value is needed, send the strip to a fluorescence reader for the T/C value, convert through the standard curve, and cross-check correlation against ELISA or HPLC.

Reading grade Band appearance Corresponding GICA concentration Corresponding FICA concentration
Negative (-) Both T and C lines clear, T line not weakened Below 15.6 ng/mL Below 3.12 ng/mL
Weak positive (±) C line normal, T line paler 15.6-500 ng/mL 3.12-200 ng/mL
Positive (+) C line normal, T line absent (fully inhibited) Not below 500 ng/mL Not below 200 ng/mL
Invalid C line absent Strip discarded, test repeated, not included in the reading

Two details are easy to misread. To begin with, the table above gives the grading thresholds for standard solutions; real samples are diluted 10-fold, and the paper converts the semi-quantitative thresholds for spiked samples in its Table 2 to GICA 156 / 5000 ng/mL and FICA 31.2 / 2000 ng/mL, with the quantitative detection limits raised accordingly to 103 and 20.4 ng/mL. Do not mix the two conventions when copying figures. Second, when the C line is absent the result is invalid however bright the T line - that is a signal of failed chromatography or degraded reagent, not a negative.

5. Don't use the wrong waveband: 254, 302 and 365 nm each do their own job

In work of this kind the value of a three-wavelength lamp is precisely that you can choose, not that you can switch everything on. The probe excitation peak is at 360 nm, close to the 365 nm long-wave channel; the 302 nm mid-wave and 254 nm short-wave channels are off the excitation peak, where fluorescence efficiency is low, and the short-wave channel brings more noticeable ozone and corneal irritation and may accelerate fading of the fluorescent signal under prolonged exposure. For FICA reading, switch on 365 nm alone and leave the other two channels off.

Channel Center intensity at 10 cm Role in this workflow
365 nm (UV-A) 1236 μW/cm² Excites the fluorescent microspheres that absorb at 360 nm, observing the 610 nm emission, for FICA band reading
302 nm (UV-B) 848 μW/cm² Not used for fluorescence excitation here; can be used for mid-wave UV transmission, UV adhesive curing and similar checks
254 nm (UV-C) 1170 μW/cm² Not used for fluorescence excitation here; switched on just for short-wave scatter observation or quartz component checks

Viewing conditions are worth fixing as well. The distance of a handheld lamp changes the irradiance, and the eye's judgment of band brightness is highly subjective, so the steadier practice for batch reading is to mount the lamp on a benchtop stand, place the strip at a fixed position and angle, and have the same person read a batch under the same ambient light; where a record is needed, photograph with a fixed exposure rather than comparing brightness from memory. For how the other two channels of the same lamp are used in other situations, see four uses of the LELMS-38L in UV inspection of optical glass .

6. How far the method can be trusted

The paper validates accuracy, specificity and stability, and these data determine how much trust the word "screening" can carry.

Validation item GICA FICA
Spiked recovery 88.4%-103.6%, RSD 2.07%-9.08% (n = 3) 84.2%-97.7%, RSD 2.40%-11.6% (n = 3)
Cross-reactivity Ferulic acid 11.7%; eugenol, methylvanillin and ethylvanillin all below 0.1% Ferulic acid 11.2%; the rest below 0.1%
60-day stability at room temperature T/C 1.21-1.26 at 0 ng/mL, 0.293-0.306 at 200 ng/mL T/C 4.06-4.19 at 0 ng/mL, 0.327-0.393 at 100 ng/mL
Detection in real samples Positive 2105-32424 ng/mL (or ng/g) Positive 2213-31258 ng/mL (or ng/g)

Eleven samples were collected in total (6 functional drinks, 5 formula milk powders); semi-quantitative results were 4 negative, 1 weak positive and 6 positive. Quantitative results from the two strips correlated closely with the reference ELISA and HPLC, and negative samples were not detected by any of the three methods. The paper also carried out an AGREE greenness assessment with a score of 0.82, and notes that field use still has to reckon with bias from different food matrices and with storage stability under extreme conditions.

To state the boundary clearly: a strip is a screening tool, and what it decides is whether there is a risk of exceeding the limit and whether the sample should be sent for testing; a regulatory report still requires confirmation by chromatography or LC-MS/MS. Visual grading of fluorescent bands is affected by ambient light, lamp distance, viewing angle and the operator, and any quantitative conclusion rests on the reader's T/C value and the standard curve.

7. Where else the lamp-plus-strip combination can be applied

What is worth reusing is not vanillin specifically but the chain of long-wave UV excitation, visual semi-quantitation and reader-based quantitation. For immunochromatographic strips labeled with fluorescent microspheres, quantum dot microspheres or time-resolved fluorescent microspheres, the excitation peak usually falls between 300 and 400 nm; on-site checks of fluorescent spots on thin-layer chromatography plates, of fluorescent whitening agents and of residues likewise need the signal raised under a dark background with 365 nm long-wave UV. The requirements such work places on a light source are: the waveband matches, the spot is uniform enough, background visible light is low enough, and the lamp can be switched one-handed and fixed in place for long periods - which is exactly what the three independent switches and the black filter of a three-wavelength lamp provide.

When choosing, confirm the excitation and emission peaks of the label, then decide which channel to use and whether blocking filter glasses are needed; if the excitation peak moves into the blue or green (labels at 470 nm or 530 nm, for example), it is time for a dedicated fluorescence excitation source rather than persisting with a UV lamp. For more comparisons of three-wavelength and handheld UV equipment, see the laboratory UV lamps section .

Common questions

Which channel of the LELMS-38L does the paper use, and does it say?

The paper writes just "Three-Wavelength UV Lamp LELMS-38L" and does not note the specific channel, irradiation distance or duration. It gives the excitation wavelength of the fluorescent microsphere probe as 360 nm and the emission as 610 nm, from which the 365 nm long-wave UV channel can be inferred. That correspondence is an interpretation based on the spectrum, not a conclusion of the paper; when reproducing the work, go by the measured excitation peak of the label in hand.

Can this UV lamp measure the vanillin concentration directly?

No. The role of the LELMS-38L is to excite the strip and let the eye see how strong the fluorescence of the T and C lines is, which is semi-quantitative reading. The concentration values in the paper come from T/C values measured by a colloidal gold reader and a fluorescence reader, converted through the standard curve (FICA: Y = -1.5064 LgX + 3.4407, R² = 0.9945). The UV lamp does not produce a number.

Why not use 254 nm or 302 nm - isn't it brighter with all three channels on?

Brightness is not the same as useful signal. The probe excitation peak is at 360 nm, where the 365 nm channel is more efficient; 254 nm and 302 nm are off the peak and also add stray light, ozone and corneal irritation, and prolonged exposure may accelerate fluorescence fading. A three-wavelength lamp is designed to be switched on channel by channel as needed, so for strip reading switch on 365 nm alone and leave the other two for transmittance, scatter observation and other work.

FICA is five times more sensitive than GICA - does that make the colloidal gold strip obsolete?

They are not substitutes. GICA needs no equipment at all and the red T line is read by eye, which suits sites without a UV lamp or reader; FICA has a lower detection limit (2.04 ng/mL quantitative against 10.3 ng/mL) but needs an excitation source and a reader, so cost and operating demands are higher. The paper's own wording is that they are chosen for different situations, and the linear ranges differ too: GICA 15.6-500 ng/mL, FICA 3.12-200 ng/mL.

The C line is missing but the T line fluoresces - can that count as negative?

No; it is invalid and the test is repeated. The C line is coated with goat anti-mouse IgG to show that the chromatographic run worked and the reagent is active; a missing C line means something is wrong with loading, chromatography or reagent condition, and in that case no appearance of the T line has any meaning. The paper's four-grade scheme lists this case separately as ineffective.

Can a food sample be dropped straight onto the strip?

Not directly. The preparation in the paper is extraction with methanol/water 1:1, vortex for 1 min, sonication for 10 min, centrifugation at 4000 r/min for 10 min, then a 10-fold dilution of the supernatant to reduce matrix effects, after which 70 μL is loaded and chromatographed at room temperature for 7 min. Beverage and milk powder matrices differ widely, and omitting extraction and dilution sends both recovery and false positive rate out of control. The dilution also means that reported figures must be corrected to the convention in the paper's Table 2.

Does viewing fluorescent bands need a darkroom, and should protective glasses be worn?

No dedicated darkroom is needed, but ambient light must be kept down: close the blinds, and keep away from indicator lights on instruments and from direct sunlight, and contrast improves noticeably. The LELMS-38L comes with fully transparent UV protective glasses as standard, and they should be worn while viewing, with the eyes kept out of the aperture; the 254 nm short-wave channel is not used in this workflow, and if it is switched on for other work, watch for ozone and ventilation. For batch reading, mount the lamp on a benchtop stand, which holds the distance steady and leaves both hands free to record.

Literature source

Hou P, Qiao Z, Wang Q, Liu J, Song K, Fang S, Li M. Development and Application of Two Modes of Immunochromatographic Assay Strips for Vanillin Rapid Detection in Food Products. Biosensors, 2026, 16: 630. doi:10.3390/bios16110630 (published 4 November 2026, CC BY open access). The equipment is recorded as a Three-Wavelength UV Lamp LELMS-38L, Luyor Instrument Co., Ltd., Shanghai.

Related products and reading: LELMS-38L handheld three-wavelength UV lamp , UV inspection of optical glass: four uses of the LELMS-38L , laboratory UV lamps section . Xinyisheng Instruments (Shanghai) supplies the full LUYOR range of UV viewing equipment and can help match waveband, filter, protective glasses and benchtop stand to the excitation and emission wavelengths of a fluorescent label.

Related sections and models

This article belongs to the biofilm detection section.

Other sections on the same product line include UV transilluminators (excitation from below through gels and thin-layer chromatography plates, so bands are read without turning the plate over), laboratory UV lamps (single-tube and two-wavelength benchtop lamps at 254 / 302 / 365 nm), and life science instruments (the entry point for fluorescence imaging, UV crosslinking, UV transmission and cell irradiation).

Models mentioned in this article: LELMS-38L, LUV-450, XEPU-1126. Ranges, accuracy and accessory lists for each model are given on the product pages.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top