Xinysun Instrument (Shanghai) Co., Ltd.

Solutions

Breadcrumb: Home > Solutions > Fluorescent Inspection

Why Use UV Lights for Acceptance Inspection of Pipeline Degreasing Cleaning?

Updated:2026-11-16Views:

A stainless steel oxygen line comes back from degreasing with a bright, clean bore that passes visual inspection. Under a UV lamp the flange face glows yellow-green, and the line is rejected. The problem is that grease leaves no colour, no texture and no smell: in white light a well-cleaned surface and a nearly cleaned one look identical. This article covers why pure oxygen systems must be degreased, which documents set the requirements, how to choose among four degreasing methods and three chemical families, and the standard process flow. It then compares the resolution of four acceptance tests and explains why the UV fluorescence check is the step where acceptance usually stalls, with reference to inspection lamps such as the LUYOR-2130L.

A stainless steel oxygen line: degreasing and cleaning are finished, the bore has been wiped until it shines, and visual inspection finds nothing to object to. Then, at acceptance, a UV lamp is switched on and the flange face glows yellow-green - rejected, rework.

This is a familiar scene on site. The problem is not the cleaning process but what cannot be seen: grease residue does not change the colour of the metal, does not change its surface finish and produces no smell. Under ordinary white light, "washed thoroughly" and "almost there" look exactly the same. Nothing but a UV lamp at 320-380 nm will show the difference.

This article avoids generalities and deals with three things that actually stop work on site: why the pipe must be degreased, how the degreasing is done, and why the UV lamp method is the one that can check every surface at acceptance; along the way it sets out the figures a degreasing inspection blacklight has to meet to be usable for acceptance, and how the LUYOR-2130L is used on real oxygen line projects: how to work it, how to judge, how to keep the record.

Key points

  • Oxygen-wetted parts must be degreased because pure oxygen supports combustion: grease residue is an ignition hazard the eye cannot see, not a question of whether the part looks dirty.

  • HG 20202 lists four test methods. Of these, the UV lamp method is the one that combines on-site working, an immediate result, full coverage, a photographic record and no damage to the part.

  • A lamp used for acceptance has to meet three hard figures: centre intensity, effective spot and white light level; a lamp that is not bright enough, or whose spot is too small, produces a false pass.

  • The LUYOR-2130L is a wide-area model with three 365 nm UV-A LEDs: about 25000 μW/cm² at 150 mm, a spot of about 100 mm and white light below 15 lux.

  • The key actions on site are "far, then near" and "wipe once": scan the whole area from a distance, confirm points up close; most of what wipes away is fibre and dust, and what does not wipe away is grease.

1. Why the pipe must be degreased: a little oil in pure oxygen is an explosion

Start with the principle, because it decides why every later check has to be that strict.

Oxygen does not itself burn, but it is a strong oxidiser and supports combustion. In air at room temperature iron and copper are "non-flammable" materials; in pure oxygen they both burn steadily. Grease left on the bore is energised by the high-velocity oxygen stream and by impact from solid particles, and heats up locally; once the temperature passes the ignition point the pipe wall itself ignites, and pure oxygen makes the fire burn harder, concentrating heat until the wall burns through and the system explodes.

1. Grease left on the bore→2. Oxygen at high velocity (elbows, tees, valve throats)→3. Particle impact and friction create a hot spot→4. Grease or metal particles ignite→5. Pure oxygen feeds the fire and heat builds→6. The wall burns through and the system explodes

Risk therefore follows three variables: the purer the oxygen, the greater the hazard (high-purity oxygen is far more hazardous than oxygen-enriched air), the higher the pressure and velocity, the greater the hazard, the smaller the bore and the sharper the throttling, the greater the hazard (the same flow runs faster in a small pipe and at an elbow). This explains why the oxygen lines of a gasification unit, the inlet and outlet of an oxygen compressor in an air separation plant, and medical central oxygen piping are all locations with strict degreasing requirements.

The cases below normally need degreasing and acceptance testing as soon as the medium touches oxygen:

CaseTypical objectsWhy degrease
Air separation and industrial gasesOxygen lines in cryogenic air separation plants, oxygen compressor piping, liquid oxygen tanks and linesOxygen purity is very high, so any grease residue is an ignition source
Medical gas engineeringHospital central oxygen piping, manifolds, pressure regulators, terminalsOccupied buildings, the highest safety class, with gas purity also specified
Chemical and energyOxygen lines in coal gasification units, hydrogen and liquid oxygen systemsHigh pressure, high flow, many throttling points, concentrated risk
Equipment and test rigsLiquid oxygen systems, high-pressure oxygen test benches, oxygen valves and instrumentsFrequent starts and stops, extreme conditions, demanding cleanliness

Table 1 Typical cases that need degreasing and acceptance (all oxygen-wetted surfaces)

The chain of standards: where degreasing is written down

DocumentCoversRelation to this topic
Degreasing Engineering Construction and Acceptance Specification, HG 20202Degreasing work and acceptanceGives four test methods, including UV lamp inspection, with pass criteria; the direct basis for this work
Safety Technical Code for the Production of Oxygen and Related Gases by Deep Cooling, GB 16912Oxygen production and use safetyRequires oxygen-wetted parts to be degreased and stresses preventing recontamination afterwards
Code for Construction of Industrial Metallic Piping, GB 50235Industrial metallic piping constructionSets cleanliness requirements and inspection steps for oxygen piping
Technical Conditions for Valves for Oxygen Service, GB/T 12244Oxygen valvesSets limits for grease residue in valve bodies and on sealing faces (≤125 mg/m² is commonly quoted)
ASTM G93-96 (common on export projects)Oxygen system cleanlinessThe usual criterion is surface oil content below 1 g/m²

Table 2 The chain of standards relevant to degreasing. Names and editions follow the project design documents, tender documents and contract.

One magnitude worth remembering: The usual ASTM G93-96 requirement for surface oil is below 1 g/m². What does 1 g/m² mean? Roughly less than half a drop of oil spread evenly over the area of an A4 sheet. A residue that small is still a hazard that has to be removed, which is why degreasing cannot be judged by "it looks clean".

2. How pipe degreasing is done: four methods, three chemical families, one flow

Understand the process and you can see, at acceptance, where problems are likely to arise. Degreasing comes down to three things: which method, which chemical, in which order.

How to choose among the four methods

MethodApplies toAdvantagesLimits
Immersion (tank)Removable pipe spools, flanges, valves, gaskets, fastenersFull coverage of internal surfaces, even result, batch handlingNeeds a degreasing tank and space; unsuitable for very long spools or installed lines
Wiping / swabbingValve bodies, isolated spots and pipe ends that cannot be immersedFlexible, local treatment, simple toolsSlow, and the result depends on how careful the operator is; fabric fibres are easily left behind
Circulation (forced circulation)Long installed lines, large-diameter mainsCovers the whole system in one pass, uniform result, less labourNeeds a cleaning pump skid and a temporary loop; a large amount of preparation
SprayingVessel internals, large-diameter sectionsLarge coverage, handles big cavitiesNeeds dedicated equipment; spray shadows remain

Table 3 Where the four common degreasing methods apply and where they do not

One line on selection: use immersion for prefabricated spools wherever possible, because the result is even; for long lines already installed, circulation is less labour and more reliable than wiping each section repeatedly, because it gives every section and every component the same treatment, while hand wiping varies from crew to crew.

Which chemical family to choose

  • Organic solvents (carbon tetrachloride, trichloroethylene, acetone and similar): strong degreasing power, usable at room temperature. Note carefully: carbon tetrachloride is toxic, volatile and a controlled substance; use it with an inhibitor, never with water present, and with strict ventilation and personal protection. Many projects now move to alternatives where they can.

  • Water-based alkaline (for example 3-5% sodium hydroxide, steam-heated to about 80℃ for immersion): low cost, easy waste treatment, reusable, and widely used. Watch compatibility with aluminium and similar materials, and rinse thoroughly to neutral after degreasing.

  • Water-based neutral / emulsifying (emulsifying degreasers containing surfactants): mild, kind to the substrate, suited to situations where strong alkali cannot be used.

Two requirements that are easily missed: the degreaser itself can carry oil, so a solvent above the oil limit has to be de-oiled and tested before use; and a degreased pipe must not be pressure tested or purged with an oil-containing medium, or the cleaning so far is wasted.

A standard flow (typical for oxygen lines)

Water rinse / system pressure test→Degrease→Water rinse→Acid clean→Water rinse→Second degreasing→Water rinse→Passivate→Cleanliness check→Oil-free air / nitrogen purge and dry

Acid cleaning removes rust and welding slag; passivation grows a dense protective film so the steel does not rust again after degreasing; the cleanliness check is the degreasing inspection this article is about. Once the flow is finished, a pipe that passes should be passivated or closed off with dry nitrogen as soon as possible to prevent recontamination - much of the rework comes from a pipe that was soiled again after it had already passed.

3. Why acceptance stalls at the inspection step: four test methods compared

HG 20202 gives four usable test methods; a project usually chooses one, and they can corroborate each other. On a construction site, however, their practicality differs enormously.

MethodHow it is donePass criterionFull coverageRecord
UV lamp inspectionIlluminate the degreased surface with a UV source at 3200-3800 angstrom (320-380 nm)No violet-blue (often yellow-green on site) fluorescence on the surfaceYes, suitable for full inspectionCan be photographed for the record
White filter paper wipeWipe the degreased surface with clean, dry white filter paperNo grease mark on the paperCovers reachable areasThe paper can be kept
Camphor testBlow off with oil-free steam and drop a pure camphor grain no larger than 1 mm across into the condensateThe camphor grain keeps rotatingNot suitable for full inspectionWritten record
AnalysisSample and analyse the degreasing bath or the surface oil contentCommon criteria: oil content of the bath ≤350 mg/L; surface residue ≤125 mg/m²Not suitable for full inspectionProduces a laboratory report

Table 4 The four degreasing test methods compared. Criteria and limits follow the specification clauses and design documents applicable to the project.

Key point one: the specification asks for everything to be checked. That is, not a few sample points but every oxygen-wetted surface. This requirement alone puts the UV lamp at the front, because it is the method that can walk over each location without contact and without damage.
Key point two: of the four, the UV lamp is the one that meets all five conditions. Workable on site, immediate result, covers every location, produces an image record, and does not damage the part. Filter paper and camphor suit re-checking a suspect spot, analysis suits quantitative sampling and reports, and none of them suits being the main full-inspection method.

What to do when the pipe is too small for the lamp

A pipe too narrow for the lamp head is a problem every site meets. The usual practice is to wipe the bore repeatedly with a clean, oil-free non-woven cloth or white cloth, then take the cloth into the dark and illuminate it with a blacklight. No fluorescence on the cloth means that section passes; fluorescent spots mean grease is still on the bore and the section has to be degreased again.

4. Not every UV lamp can be used for acceptance: three hard figures

"Buying a UV lamp" and "buying a degreasing inspection blacklight that can be used for acceptance" are two different things. The decision rests on three figures that can be measured.

Figure one: centre UV intensity (μW/cm²) - can you see it at all?

The thinner the grease residue, the weaker its fluorescence under UV. Whether weak fluorescence can be excited at all depends directly on the UV intensity reaching the surface. A lamp that is not strong enough still looks violet to the eye, but a thin oil film does not fluoresce, and the operator concludes that the surface is clean. This is the dangerous failure mode in degreasing inspection: the surface is signed off as passing when the lamp simply could not reveal it, what is usually called a false pass.

Figure two: effective spot diameter (mm) - how fast, and what gets missed

Many of the places to be checked on piping are lines and rings: a flange face is a full circle, a pipe end is a circle, a weld is a line. With a small spot you have to move inch by inch, which is slow and easily skips a patch; with a large enough spot, one or two passes cover a flange. For full inspection over large areas the lamp has to be wide enough.

Figure three: white light and stray light level (lux) - can you tell them apart

The value of a blacklight is that it emits UV and little visible light. If the lamp also pours out white light, weak fluorescence is drowned and the eye cannot separate it. A good degreasing inspection lamp uses an efficient filter to push the white light down; in a dark environment the contrast is higher and the eyes tire less over a long inspection.

One softer point: instant start and frequent switching

Inspecting oxygen lines often means climbing, entering vessels and working point by point. A conventional high-pressure mercury lamp needs about 5 minutes of warm-up, its bulb surface reaches 200-300℃, and frequent switching shortens its life noticeably. On a site where you keep moving, all three cost real time. A UV-A LED is a cold source that starts instantly and can be switched at will, which makes a clear difference in use.

ItemOrdinary UV torch / banknote checkerConventional high-pressure mercury blacklightLUYOR-2130L (UV-A LED)
WavelengthOften 395 nm or a mixed bandMainly 365 nm365 nm, 360-370 nm band, pure UVA
White light controlMostly unfiltered, much white lightFilteredEfficient filter, cuts over 90% of white light, below 15 lux at 150 mm
Start-upInstantAbout 5 minutes warm-upInstant, full brightness
Frequent switchingPossibleNot advisedPossible, three levels on a touch switch
Surface temperatureLow200-300℃Low (aviation aluminium body dissipates heat)
Source lifeSeveral thousand hoursHundreds to several thousand hoursAbout 50000 hours
RoleGeneral lighting / entertainmentEarly degreasing inspectionOn-site degreasing inspection and acceptance

Table 5 Three common UV sources compared

5. LUYOR-2130L: three LEDs in a wide-area source designed for pipe degreasing acceptance

The LUYOR-2130L is a torch-style blacklight from LUYOR for large-area degreasing inspection. Its design choices map onto the three figures in the previous section.

Three high-power 365 nm LEDs

The head carries three high-power UV-A LEDs with a centre wavelength of 365 nm in the 360-370 nm band, pure UVA with no UVB or UVC. Three side by side are there to deliver enough intensity and enough spot.

Wide-area distribution, not a spotlight

It lights a surface, not a point. The effective spot is about 100 mm across at 150 mm from the head, so a flange face can be covered in one or two passes.

An efficient filter holds the white light down

The filter cuts over 90% of white light, and white light at 150 mm is below 15 lux. In a dark environment the contrast is high and even a faint residue is visible.

Three more details that matter on site: Three brightness levels are switched with a touch switch at the tail, which carries a digital battery display so you do not have to guess how much charge is left; the body is hard-anodised aviation aluminium, which sheds heat quickly, and the unit weighs about 600 g with batteries, so long hand-held sessions are not tiring; the standard package includes LUV-10 UV safety glasses, a high-capacity lithium battery pack, a 110-260 V wide-range charger and an aluminium carry case, with a 3-year warranty on the unit. It is the current model, following the LPX-365 (discontinued in 2014) and the LUYOR-2130 (discontinued in 2016).

The key data: intensity, spot and distance

150 mmCentre intensity about 25000 μW/cm²
Spot diameter about 100 mm
White light <15 lux
250 mmCentre intensity about 13000 μW/cm²
Spot diameter about 150 mm
White light <10 lux
300 mmCentre intensity about 10000 μW/cm²
Spot diameter about 200 mm
White light <8 lux
380 mmCentre intensity about 6500 μW/cm²
(38 cm reference distance)
For fast scanning of large areas

Three points matter when reading this set of figures:

  1. Intensity falls quickly with distance. Double the distance and the intensity drops to roughly a quarter. So "can I see it" is a question of how far away you stand rather than of how much the lamp cost.

  2. Spot and intensity trade off. Farther away shows a wider area but a shallower one; closer shows detail but a narrow band. You cannot have both at once.

  3. The method therefore runs "far, then near". Start at the middle or low level and scan the whole surface from 250-380 mm; where a suspect bright spot appears, switch to high and move in to about 150 mm to confirm.

One industry reference point: Industry material on oxygen line cleaning acceptance carries wording that the inside of a line was inspected with a high-intensity lamp or the UV degreasing inspection lamp LUYOR-2130L and no fluorescence appeared. That corresponds to the ASTM G93-96 requirement of surface oil below 1 g/m². It shows that the lamp is a tool the trade has accepted at the acceptance step and has written into construction plans, not just a figure on a brochure page.
Why Use UV Lights for Acceptance Inspection of Pipeline Degreasing Cleaning?(图1)Three LED head, aviation aluminium body and a digital battery display at the tail - no extra test gear needed on site to work out the charge.

6. Site SOP: taking the 2130L along the whole line

Compressed into an executable sequence, all of the above becomes the seven steps below.

1
Prepare the environment

Bring the light on site down as low as possible, screening a local area with blackout cloth where needed; check ventilation; put on the LUV-10 UV safety glasses from the kit; have oil-free white cloth or non-woven cloth, a record sheet and a pen ready.

2
Split the line into sections and list the points to check

By pipe spool number, list the bore, flange faces, welds and heat-affected zones, threaded joints, elbows and tees, valve bodies and seats, gaskets, heads, and every connection that was opened before installation.

3
Fix two variables

Fix the brightness level (middle, for consistency) and the scanning distance (250 mm, for example). Using one set of conditions before and after makes comparison, repeatability and independent re-checking possible.

4
Scan the whole surface

Work along the pipe, section by section, with the spots of successive passes slightly overlapping so nothing is skipped. Look at the whole from a distance and move quickly along the run.

5
Confirm suspect points

Switch to high, move in to 150 mm, illuminate as square to the surface as possible and look from several angles. Wipe with oil-free white cloth and look again where necessary.

6
Judge and record

Record line by line as "spool - location - conclusion - inspector - date", and photograph anything suspect. The record itself is part of the acceptance documentation.

7
Re-check and close up

Degrease and re-check any location that failed; once a whole section passes, passivate it or close the ends with dry nitrogen straight away to prevent recontamination.

How to illuminate different locations: a few practical tips

  • Flange faces: hold the head square to the face and illuminate in 3-4 passes around the circle so the full ring is covered with no gap.

  • Pipe-end bores: push the head slightly into the end and angle it towards the bore, keeping your own shadow out of the way.

  • Vessel and tank internals: run the body close to the wall in an S pattern; corners and the far end need a separate closer pass, since these are the places easily missed.

  • Small-bore pipe: switch to the cloth method - wipe the bore with oil-free white cloth and illuminate the cloth.

  • Valve bodies: dismantle the valve and inspect one by one; the seat and sealing face matter most, because grease there is easily hidden once the valve is assembled.

7. Reading the result: what passes, and which fluorescence is not oil

The pass criterion for UV lamp inspection is simple: no violet-blue (often yellow-green on site) fluorescence on the surface. The difficulty on site is separating the fluorescence of grease from the fluorescence of everything else.

InterferenceFluorescence signatureHow to tell
Cotton and fabric fibresThin filaments, drawn out, bright blue-whiteWipe with oil-free white cloth and it comes away
Dust and paper fragmentsScattered points, sharp boundaryBlow off or wipe away
Residue of some cleaners or degreasersIn patches, even, following the cleaning pathOne more rinse and it disappears
Rust-preventive oil / cutting fluid / marker inkSpots and lines with a definite directionStill there after wiping; degrease again
Sealant, coating, label adhesiveLocal patches with clear boundariesCheck against the process step; do not misread it
Hand sweat / skin oilFingerprint shapedChange gloves and look again

Table 6 Common interference that fluoresces under UV but is not grease residue

The "wipe once" test: wipe with oil-free white cloth. What wipes away is usually foreign fibre and dust; what stays, fixed on a sealing face or a weld, may be grease that has soaked into the surface and should be treated as a failure.

Form adds another clue: drawn out lengthwise, with blurred edges and running into bands is usually the mark left by fabric fibre rubbing; spots with sharp edges, fixed on a sealing face or a weld are usually genuine grease residue.

8. Keeping "is the lamp still accurate" under control

Every UV source loses output with use, LEDs included, though far more slowly. In degreasing inspection this matters: once a lamp has decayed far enough, residual oil stops showing and the inspection turns into a false pass - which is more dangerous than no inspection at all, because it produces a wrong release decision.

Two controls are worth putting in place:

Establish an intensity baseline

Fix the distance and the brightness level, measure centre intensity with a UV meter at intervals, and enter it in the equipment log. A lamp is a measuring instrument and should have one.

Set a replacement threshold

For example, send the lamp for service or replace the source when centre intensity falls below 70% of its initial value. Put the threshold in the work instruction so the decision does not rest on how someone feels.

Meters that go with it: the LUYOR-340 UV meter, and UV radiometers from Spectroline and other brands. We can supply a measurement and logging scheme that fits your existing record format.

9. Choosing a lamp by task: how the common degreasing and fluorescence inspection lamps divide the work

Degreasing inspection is not one single situation, so one lamp does not cover everything. Split by "surface or point, and whether a report is needed", the division of work looks roughly like this:

ModelBeam typeKey dataBetter for
LUYOR-2130LWide area (3 LEDs)About 25000 μW/cm² at 150 mm, spot about 100 mm, white light <15 luxFull degreasing inspection of oxygen lines and vessels; a flange ring in one pass
LUYOR-3180Spotlight30000-40000 μW/cm² at 38 cm, centre beam about 30 mmPoint fluorescence: leaks, fingerprints, fine cracks; reaches farther
MNT-365ACleanroomSmooth, low-particle bodyParticle and biofilm inspection in cleanrooms

Table 7 Selection by task

One line to remember: 2130L for a surface, 3180 for a point;


References

The cleaning acceptance standards and specification clauses mentioned here can all be traced; check the originals against the official publications below:

  • ASTM G93, cleaning methods and cleanliness classes for pure oxygen systems, ASTM International: astm.org/g0093
  • GB 16912, Safety technical code for the production of oxygen and related gases by deep cooling, National Standard Full Text Public System: openstd.samr.gov.cn
  • GB 50235, Code for construction of industrial metallic piping, National Standard Full Text Public System: openstd.samr.gov.cn

Related sections and models

This article belongs to the fluorescence inspection section.

Other sections on the same product line include laboratory UV lamps (254 / 302 / 365nm single-tube and dual-wavelength benchtop lamps), 365nm blacklights (UV area lamps for NDT, leak detection and fluorescence inspection, judged by irradiance rather than wattage), life science instruments (the entry point for fluorescence imaging, UV crosslinking, UV transmission and cell irradiation).

Models mentioned in this article: LUYOR-2130L, LUYOR-340, LUYOR-3180. Ranges, accuracy and accessory lists for each model are listed on the product pages.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top