Xinysun Instrument (Shanghai) Co., Ltd.

Solutions

Breadcrumb: Home > Solutions > Fluorescent Inspection

365nm or 385nm? Choosing the UV Wavelength for Counterfeit Detection

Updated:2026-11-02Views:

Roll-fed tickets, identity documents and pharmaceutical cartons run through a press at hundreds of meters per minute, far too fast for the eye to read a UV fluorescent security feature, and a continuously lit black light can inspect stationary samples but nothing that moves. This article explains why anti-counterfeit inspection defaults to 365 nm, when 385 nm is worth considering, how an ink maker's data sheet and the position of the mark settle the choice, why UV-curing ink is a trap, and how the 906UV UV stroboscope freezes that motion long enough to read the feature.

Roll-fed tickets, identity documents and pharmaceutical cartons pass along the line at hundreds of meters per minute, and the UV fluorescent security features printed on them move far too fast for the eye to read. A continuously lit black light can inspect stationary samples, but against a continuous web of printed work, staring will not hold it - seeing a security feature in motion clearly requires a UV stroboscope that can freeze it at high speed. LUYOR-906UV is a product designed for this kind of work: 40 × 365-375 nm UV LEDs, a flash range of 60-300,000 flashes per minute, and internal/external triggering with phase shift control. Before selection, settle the wavelength question.

1. Why UV anti-counterfeit inspection defaults to 365 nm

The excitation peaks of mainstream security dyes, covert taggants and optical brighteners mostly fall in the 350-370 nm range, and ink makers' technical data sheets (TDS) usually specify 365 nm as the recommended excitation wavelength. 365 nm sits near the peak of that range, so a larger share of the UV energy landing on the substrate is converted into visible fluorescence - at the same output power, the mark appears brighter.

More important is background contrast. A 365 nm LED emits almost pure UV-A with very little visible spill, so the fluorescent mark glows against a near-black background instead of being covered by a haze of violet light. When the eye has to judge a weak mark or a low-concentration feature on a moving line, that contrast decides between "visible" and "invisible".

2. When to consider 385 nm

365 nm is not right for every case. In the following situations, 385 nm should be evaluated:

  • The mark sits under a coating: titanium dioxide (TiO2) in white ink blocks ultraviolet below about 380 nm. If the fluorescent layer lies beneath white ink, varnish or lamination, 365 nm may be absorbed before it reaches the ink layer; 385 nm sits above that cutoff, so the energy gets through.
  • The ink is designed for a longer wavelength: some newer taggants specify an excitation range of 385-395 nm, stated plainly on the TDS; follow the specified value and the choice is correct.
  • Paper background interference: paper with a heavy loading of optical brightener glows overall under 365 nm and easily drowns the mark; moving to 385 nm sometimes suppresses the background and preserves the signal.
  • Confirming that the lamp is on: 385 nm leaves a faint violet cast on the workpiece, so in a noisy workshop the operator can confirm at a glance that the source is working.

Alongside the 365-375 nm version, the LUYOR-906UV series includes a 385 nm wavelength version; a line running mixed ink chemistries can specify the wavelength for its main ink system rather than compromise.

3. Two questions settle the wavelength

1. Check the ink maker's technical data sheet

The ink supplier's TDS lists the recommended excitation wavelength, or gives an excitation curve, and that single data point answers the selection question. When in doubt, send the TDS to our technical colleagues and read it together - far less trouble than trying one lamp after another.

2. Look at whether the mark is on the surface or under a coating

Marks printed on the surface favor 365 nm; marks beneath white ink, varnish or lamination favor an evaluation of 385 nm. If two chemistries run on one line and the budget covers one instrument, 365 nm is the safer default - unless most of the work orders sit under transparent or white overprint, in which case specify 385 nm directly.

4. Watch out for the UV-curing ink trap

UV-curing ink is cured by ultraviolet, but usually does not fluoresce. If the inspection target is print register or defects in ordinary four-color work, a UV stroboscope will not help - what is needed is a white-light stroboscope, such as the LUYOR-906 on the same platform. Decide whether the mark to be seen emits light before deciding which lamp to use, and a detour is avoided.

5. Typical applications of LUYOR-906UV

  • Currency and tickets: on-line inspection of UV security features on banknotes, checks, bank tickets and tax and financial documents;
  • Identity and official documents: verification of security features on identity cards, passports, ballot papers, government bonds and stamps;
  • Pharmaceutical packaging: verification of anti-counterfeit and tracking marks on blister packs and labels;
  • Textiles and coatings: inspection of the distribution and integrity of functional coatings such as OAA;
  • Fluorescent penetrant inspection: development observation in liquid and magnetic fluorescent penetrant NDT, with operating points covered in five common mistakes in UV-A fluorescent penetrant testing;
  • Invisible barcodes and taggants: reading and locating low-concentration covert labels and invisible barcodes.

These applications share one feature: the mark is invisible or very weak, and the target is moving - exactly the range in which stroboscopic freezing works.

6. Why 906UV suits these scenarios

The spectrum matches. 40 imported UV LEDs at 365-375 nm, with a reflective design that evens the output, so security features develop clearly without the bright-center, dark-edge banding that a lamp array can produce.

Wide speed coverage. Internal and external trigger ranges are both 60-300,000 flashes per minute, so a stop point can be found from low-speed webs to high-speed press lines; external triggering supports phase shift (lag angle) control to place the flash at a more suitable observation position.

It keeps up with a continuous line. With a photoelectric, Hall or proximity switch signal on the external trigger, the photoelectric signal can be used for automatic pattern tracking, so the security feature stops drifting as the web runs.

It lasts a long shift. A handheld body of about 1 kg with a built-in DC8.4V 2800mAh lithium battery runs more than 10 hours on a full charge, and with automatic flash stop and parameter memory the whole shift passes without frequent interruption of inspection.

7. Points for use on site

  • Dim the ambient light. The contrast of UV fluorescence is bought with a dark background: switch off or shield visible light sources in the field of view and weak marks develop more easily;
  • Protect yourself. UV output is high in intensity, so the operator should wear UV protective goggles, must not look directly into the LED array, and should avoid leaving skin exposed in the irradiated area for long periods;
  • Divide the work. Give anti-counterfeit development and location to the 906UV, and ordinary register and defect inspection to the white-light 906; two instruments are more efficient than one;
  • Beware of multiple-frequency ambiguity. A stopped image does not mean a true state has been seen - the frequency may sit on a multiple or a submultiple, and the troubleshooting steps are the same as in the LUYOR-906L application case.

8. Frequently asked questions

How does LUYOR-906UV differ from a continuously lit black light?

The working mode differs: a black light is a continuous source, suited to UV inspection of stationary samples; the 906UV is a stroboscope that freezes a moving object with high-frequency flashes, suited to on-line and high-speed inspection. The uses overlap, but the scenarios complement each other - a continuous lamp cannot illuminate printed work on a moving web.

What if a mark does not show under 365 nm?

Check the excitation curve on the ink TDS and confirm the specified wavelength; then confirm whether the mark sits under white ink, varnish or lamination - if so, evaluate the 385 nm version. For low-concentration features, signal-to-noise can also be raised by dimming the ambient light and shortening the observation distance.

Can it check ordinary print register?

It can for the development, omission and location of fluorescent security features; ordinary four-color register and defect inspection should use a white-light stroboscope. UV-curing inks usually do not fluoresce, so illuminating ordinary ink with it gives no fluorescence to see.

How do I choose the 385 nm version in the series?

Two points: the excitation range specified on the ink TDS, and whether the mark is on the surface or under a coating. Choose 365-375 nm for surface marks; choose the 385 nm version for marks under a coating or for inks specified at 385-395 nm. Where a mixed line can buy one instrument, 365 nm is the safer choice.

What safety requirements apply in use?

Wear UV protective goggles, do not look into the LED array, and avoid leaving skin exposed in the irradiated area for long periods; when working in an area where people pass, notify them in advance and mark out the irradiated zone.

Related products and further reading

Conclusion

Wavelength selection for UV anti-counterfeit inspection is less complicated than it looks: check the ink TDS once, look once at where the mark sits, and the division between 365 nm and 385 nm becomes clear. For most ticket, document and pharmaceutical carton lines, the 365-375 nm LUYOR-906UV is enough to freeze a moving security feature clearly; applications genuinely blocked by white ink or lamination are the ones to consider the 385 nm version for. To confirm a choice against a specific ink and line speed, contact the Xinysun technical team.

Related sections and models

This article belongs to the fluorescent penetrant inspection section.

Other sections on the same product line include stroboscopes (freezing rotation and reciprocation by persistence of vision, showing the process rather than a number) and industrial test instruments (the entry point for the four lines of UV inspection, speed measurement, stroboscopic observation and surface inspection).

Models mentioned in this article: LUYOR-906UV, LUYOR-906, LUYOR-906L. Ranges, accuracy and accessory lists for each model are given on the product pages.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top