Breadcrumb: Home > Solutions > Fluorescent Inspection
Updated:2026-11-02
Views: For fluorescent magnetic particle or penetrant testing of castings, forgings, welded shells and long shaft parts, the difficulty is often not the penetrant but whether there is a light field large enough, bright enough and clean enough. Sweeping a large workpiece with a small-spot lamp means the inspector spends half the time repositioning, irradiance falls away at the edge of the spot, and edge defects are easily passed. This article covers what ASTM E3022-26 has tightened, how to choose among the three intensity levels, and whether to run on mains power or battery.
For fluorescent magnetic particle (MT) or fluorescent penetrant (PT) testing of castings, forgings, welded shells and long shaft parts, the difficulty is often not the penetrant but whether there is a light field large enough, bright enough and clean enough. Sweep a large workpiece with a small-spot lamp and the inspector spends half the time repositioning and aligning; irradiance falls off at the edge of the spot, and edge defects are easy to pass.
The LUYOR-BB series is designed for this kind of work: a large-area UV-A inspection lamp with an array of 8 high-power 365 nm LEDs, a white-light blocking filter system, ASTM E3022-26 certification across the range, and three intensity levels covering different workpieces and working distances. This article is organized in three layers - why, how to choose, and how to accept delivery - so that the basis for selection is clear and several common differences in quoted figures are explained.
Fluorescent inspection relies on the faint emission of indicator retained at a defect. Whether it can be seen depends on three conditions holding at the same time; miss one and the risk of a missed indication goes up:
| Condition | Requirement | Typical consequence of falling short |
|---|---|---|
| Intensity | UV-A on the inspection surface not below 1000 μW/cm2 (ASTM E3022 / ISO 3059 basis); critical parts often work to a higher requirement | Indications look dim; small cracks cannot be judged |
| Uniformity | Readings across the effective area generally meet the threshold, with no obvious dark zones or LED striping inside the spot | Looks normal locally while actually missing indications - a risk that is very hard to find after the fact |
| Spectral purity | Narrow-band 365 nm output, low visible leakage, ambient white light controlled | The background is lit up, the brightness difference between indication and background is compressed, contrast drops |
Of the three, intensity is easy to measure; uniformity and stray white light are often ignored. A small-spot lamp with a high nominal figure can still fall short at the edge of its beam.
Sweeping a 3 m circumferential weld with a 200 mm class spot, at 20% overlap, takes roughly 19 positionings; with a 280 mm class spot the same weld takes about 14. That difference of 5 is not just time: every extra positioning is another chance for the spot to be misaligned at the edge and for edge irradiance to fall below the threshold. The larger the workpiece and the larger the batch, the more the spot size affects efficiency and consistency.
All three intensity levels of the BB series have an effective spot diameter of 26-28.5 cm (defined as the area where the reading is still above 1000 μW/cm2), covering about 552-638 cm2 in a single pass - roughly twice a conventional 200 mm spot. A full circumferential weld or a whole flange no longer has to be repositioned repeatedly, and the inspection conditions stay consistent across the whole area.
| Metric | What the standard looks at | BB series position |
|---|---|---|
| Peak wavelength and spectral width | Stable peak within the UV-A band, stray short-wave UV controlled | Peak 360-370 nm, main peak 365 nm, FWHM ≤15 nm, no UVB/UVC output |
| Stray white light | Visible leakage suppressed to a level that does not affect contrast | Fitted with the LUYOR UV cut-off filter, white light test report supplied with each unit |
| Irradiance uniformity | No obvious low-value zones within the effective area | 8-LED array with uniform light mixing, irradiance uniformity report supplied with each unit |
| Driver ripple | Current ripple limited so that flicker does not affect photography and judgment | Low-ripple driver, no PWM flicker, suitable for digital capture |
Two points need to be clear. One is that the scope of ASTM E3022 is UV-A LED lamps; mercury lamps and gas discharge lamps are not covered by it, and benchmarking a mercury lamp against E3022 is not a valid comparison to begin with. The other is that the standard leaves testing and certification to the manufacturer, with no mandatory independent third-party oversight; the auditing party (NADCAP, OEM, ISO auditor) does spot-checks alone - so the buyer has to verify for themselves whether the report package is complete. Clause details are covered in the twelve questions on ASTM E3022-26.
Every BB series unit ships with three data sets - spectrum, irradiance uniformity and white light - which together with the type test report and declaration of conformity for the model form a complete package that can be submitted during an audit. The question that comes up most in practice is the difference between the type test report and the unit report: the former shows that the design of the model meets the requirement, the latter shows that the unit in your hands meets it. LED devices vary from unit to unit, and neither report can substitute for the other.
| Level | Mains / battery version | Center intensity at 38 cm | Effective spot | Battery runtime | Typical workpieces and situations |
|---|---|---|---|---|---|
| BBH high | BBHA / BBHB | 17000 μW/cm2 | 26.5 cm | About 5 h | Long-distance illumination of large structures, dark or rough surfaces, brighter ambient light on site |
| BBM medium | BBMA / BBMB | 9000 μW/cm2 | 28.5 cm | About 6 h | The main level for routine MT/PT, batch inspection of castings, forgings and welded shells |
| BBL low | BBLA / BBLB | 4000 μW/cm2 | 27.5 cm | About 7 h | Fine judgment in a dark room, long continuous shifts |
A common mistake in choosing a level is to pick the brightest. The center intensity of BBM is about half that of BBH, yet its effective spot is the widest of the three (28.5 cm), because more of the energy is distributed toward the edge so that the whole area stays above the threshold. For routine inspection where every point has to be judged, the efficiency gained from spot width usually outweighs center intensity. Conversely, when the workpiece surface absorbs strongly (black casting skin, dark coatings) or the lamp has to be used at a distance, the center intensity of BBH is what matters.
One point about the intensity figures is worth stating in advance: the "4000-22000 μW/cm2" often seen in series marketing copy is the broad range given by the factory; the per-model technical data tables give specific values - BBH 17000, BBM 9000, BBL 4000 μW/cm2, all measured at the center, 38 cm from the lamp face. Selection, tendering and process documents should follow the per-model table, otherwise acceptance can turn into a dispute about "the literature and the measurement not matching".
The A version connects to mains and weighs 1.2 kg; the B version has a built-in battery, weighs 1.7 kg and runs 5-7 hours depending on level. Light source, optics and ingress protection are identical between the two; what differs is whether you need continuous judgment on a fixed bench or you are climbing, entering tanks and moving between areas. A common arrangement in one shop is one A version for the main bench plus one or two B versions for mobile work. The B version lights instantly and does not need to cool down before restarting - in multi-point spot checking that matters more than the numbers on the datasheet.
The usual approach in compact LED inspection lamps is to pack 3-5 emitters just a few millimeters apart into a very small housing. Two consequences follow: heat concentration raises junction temperature and accelerates lumen depreciation; and when one emitter fails, light still comes out, but that patch dims quickly and is hard to spot from the outside.
The BB series takes the opposite approach - spreading the UV energy out. Eight LEDs are arranged in an array with wider spacing and enough heat dissipation area, which gives three direct results: one pass covers a working surface; junction temperature is lower and long-term depreciation is slower; and when one emitter fails, the dark zone stands out against a uniform background, so the pre-use emitter check becomes something an operator can actually do. ASTM E3022 explicitly requires failed LEDs to be replaced before use, and if the failure cannot be noticed that requirement cannot be carried out.
There is another point: when 8 emitters are packed closely, inadequate optical design leaves bright and dark striping inside the spot. The BB series uses an array light-mixing approach, with a beam profile requirement of no obvious emitter shadows or dark points - "local readings pass but the gaps between emitters are dark" is a comparatively hard-to-find source of missed indications.
For high-power versions running continuously for long periods, heat cannot be avoided. The BB series uses a built-in temperature-controlled cooling fan plus an aluminum alloy heat-sink cavity: the fan starts and stops on temperature, adjusts speed to the junction temperature requirement, carries heat away from the LED chips quickly, suppresses lumen depreciation, and balances cooling capacity against noise. This differs from a fanless passive design, so when purchasing it is worth confirming the actual structure rather than relying on older literature.
The housing is designed to IP68 and sealed against penetrant, so the whole unit can be washed down, and penetrant is less likely to accumulate in housing seams and form false fluorescence. Two points for routine cleaning: do not jet a high-pressure washer straight into the fan outlet; wipe the lens with a soft cloth and avoid abrasive cleaners, so that the filter surface does not haze or yellow and let more white light through.
On safety, the series is assessed to Risk Group 3 under IEC 62471. Operators should wear UV protective glasses for the matching band, avoid looking directly into the lamp head and avoid prolonged close-range exposure; on bench work, keep UV from spilling into the adjacent station. A related article on risk points, 5 common mistakes in UV-A fluorescent inspection, is available for comparison.
| Comparison item | Conventional mercury blacklight | LUYOR-BB (LED) |
|---|---|---|
| Start-up | 5-15 minutes warm-up to stable output | Instant light, no warm-up wait |
| Tube / light source life | 500-1000 hours, a consumable | Rated above 20000 hours |
| Annual replacements (two shifts, 16 h/day, about 4000 h/year) | About 4-8 tubes | Essentially none |
| Heat and effect on the workpiece | Hot body; prolonged close-range exposure can bake the penetrant and damage coatings and plastic parts | Cold light source, surface temperature rise controlled |
| Environment | Contains mercury; some models generate ozone; dark rooms need extraction; disposal as hazardous waste | No mercury, no ozone, no forced extraction needed in the dark room |
| Power supply form | Mostly mains; portable versions are bulky | Battery version 1.7 kg, can run off mains |
What actually carries the cost in this table is not electricity but downtime and process: mercury lamp warm-up sits inside the cycle time of every batch, tube replacement sits inside the production plan, and hazardous waste disposal sits inside the EHS register. Added up, these three items often outweigh the price difference between the lamps themselves.
The BB series is used in NDT for aerospace, rail transit, wind power, pressure vessels, construction machinery, defense subcontracting and export components, and is compatible with JB/T 4730 (non-destructive testing of pressure equipment), ASTM E709 (magnetic particle testing), ASTM E165 (penetrant testing) and ISO 3059, so one documentation package can serve both domestic testing and overseas customer audits.
In process terms: fluorescent magnetic particle testing is mostly used for surface and near-surface defects in castings, forgings and welds, and requires the spot to cover the whole magnetized zone; fluorescent penetrant testing suits non-magnetic materials and complex geometry, and requires a clean background and high contrast at judgment. Both methods ask the same thing of the light source - large area, high intensity, low stray light - and differ mainly in station layout and workpiece size, which is exactly why three intensity levels exist.
1. With a traceable UV radiometer, measure center intensity at 38 cm, compare with the data table and file the record; 2. measure along the cross directions of the spot at the edge to confirm readings across the effective area are above the threshold with no dark striping; 3. in a darkened room, measure ambient white light to confirm the inspection conditions hold; 4. visually check the filter for scratches or discoloration, check all 8 emitters for dark points that do not light, and confirm the fan starts and stops normally.
Routine management comes down to three things: fixed distance, fixed level, fixed form for periodic irradiance records; send the lamp for service or replace it when the reading falls more than 20% below the initial value; clean the filter separately and do not store it with other tools. If "the background gets brighter and the fluorescence fainter", check the filter before the penetrant and the workpiece surface - that order saves a lot of wasted investigation.
By workpiece size and station layout. The BB is a large-area light source for fixed or semi-fixed stations, with an effective spot of 26-28.5 cm, suited to full circumferential welds, whole flanges and batches of small and medium parts; the LUYOR-3103/3103D is a portable lamp with a spot of about 200 mm and 4500 μW/cm2 at 380 mm, suited to single-point judgment, field work and in-tank work. Where both lines run, a common arrangement is the BB for main judgment and the 3103 for spot checks and rechecks.
If the lamp is to be fixed above a conveyor and wider coverage is needed, look at the LUYOR-3115 overhead inspection lamp: 15 LEDs, 9500 μW/cm2 at 38 cm, a 250×500 mm spot, and an elongated coverage pattern suited to continuous workpieces on a belt. The advantage of the BB is that it can be handheld or mounted, which gives more flexibility.
A difference in basis. The overall output range for the series is written broadly (4000-22000), while the per-model technical data table gives specific values: BBH 17000, BBM 9000, BBL 4000 μW/cm2, all center intensity at 38 cm from the lamp face. Selection, tendering and acceptance should follow the per-model table; if a supplier offers a higher reading, the measurement distance and instrument model should be given as well, otherwise the figures cannot be compared.
This is a practical concern on the shop floor. The BB housing is IP68 rated and sealed against penetrant, and the fan is internal, so normal use and full washdown are unaffected; the points to watch are not jetting a high-pressure washer into the outlet and not leaving the lamp standing for long periods in penetrant-contaminated liquid. Where airborne dust is heavy, a dust cover and a shorter filter cleaning interval are advisable.
Yes. A 365 nm source works for fluorescent leak detection as well, and the advantage is the large spot, which makes sweeping a whole pipe run fast. Leak detection usually needs a higher single-point intensity to brighten a small leak, though, so if leak detection is the main job, consider the spot type LUYOR-3180 (about 40000 μW/cm2 at 38 cm); if inspection is the main job and leaks are checked occasionally, the BBM level is enough.
Not advisable. The three levels come from the light source configuration and the optical design, not from simply turning the power down; adjusting voltage yourself would compromise the low-ripple driver, directly affecting spectral stability and photographic capture, and would also make the factory report disagree with the measurement. Selecting a level for the workpiece is easier than modifying the lamp later.
Usually three things: whether the model of the lamp matches the model on the report; whether the irradiance reading on the unit report agrees with the measurement taken on site; and whether the routine irradiance records are continuous, with the measuring distance and level kept fixed. The former two depend on complete documentation, the third on management habit - printing the measuring distance, level and instrument serial number directly on the record form is a good move.
This article belongs to the fluorescent inspection section.
Other sections on the same product line include UV radiometers (measuring mW/cm2 intensity and J/cm2 accumulated energy - the tool that decides whether a lamp is compliant), 365 nm blacklight (UV area lamps for penetrant testing, leak detection and fluorescence inspection - look at irradiance, not wattage) and life science instruments (the entry point for fluorescence imaging, UV crosslinking, UV transmission and cell irradiation).
Models mentioned in this article: LUYOR-BB, LUYOR-3103, LUYOR-3115. Ranges, accuracy and accessory lists for each model are given on the product pages.
Email: info@xinysun.com
Tel: 131-2093-6518
Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai
Copyright 2026 Xinysun Instrument (Shanghai) Co., Ltd. All rights reserved.
ICP:ICP-2026046447
