Xinysun Instrument (Shanghai) Co., Ltd.

Applications

Breadcrumb: Home > Applications > Lab Research

UV Crosslinker FAQ: Uses, Selection, Differences from Ovens, and Operating Procedures

Updated:2026-11-17Views:

UV crosslinkers are not used every day in most labs, but a wrong setting is hard to undo later. The same instrument appears in Northern and Southern membrane crosslinking, in PCR carry-over decontamination, in UV mutagenesis and in photosensitizer activation. Written in question-and-answer form, this article covers what the instrument does, how to choose one - settle the wavelength before anything else, confirm a true energy mode, then check chamber size and lamp power, uniformity and sensor protection - how it differs from an oven, and how a complete run should be carried out.

The UV crosslinker is one of those instruments that a molecular biology lab does not use very often, but that is hard to recover from when it is used wrongly. It appears in the membrane crosslinking step of Northern and Southern blots, on the bench during PCR carry-over decontamination, and in UV mutagenesis and photosensitizer activation experiments. Because it is used so seldom, many labs keep running whatever machine the previous postdoc left behind, and nobody has ever checked the parameters.

The six questions below are the ones we hear most often from labs: what problem the instrument actually solves, how to choose one, how it differs from an oven, whether other equipment can stand in for it, how to judge brands, and how a complete run should go. The parameters quoted here use the LUYOR UCL-3200 / UCL-3500 and the UVP CL-3000 sold on this site as examples; the product pages remain the reference.

1. What a UV crosslinker is for

In one sentence: it uses UV light to weld nucleic acids, proteins or other biomolecules onto a solid support, or to cut and inactivate them. It is not a lighting device. Its core capability is delivering a defined UV dose (in mJ/cm² or J/cm²) that can be set, recorded and checked afterwards.

In practice the common uses fall into the following groups:

UseTypical settingKey point
Nucleic acid membrane crosslinkingSouthern / Northern / Dot / Slot blot, EMSA - fixing DNA or RNA onto nylon or nitrocellulose membranesToo little dose and the nucleic acid washes off; too much and fragments break, raising background
PCR decontaminationRemoving residual amplicons from bench surfaces, pipettes, PCR tubes and consumables254 nm damages DNA directly and is a common physical route for amplicon control
UV sterilizationSurface disinfection of clean-bench interiors and small implementsWorks on surfaces the light reaches directly; shadowed areas are not treated
UV mutagenesis / breedingBuilding random mutant libraries in microbes and plant materialMutation rate is controlled by the dose-survival curve, so the dose has to be reproducible
Pyrimidine dimer inductionDNA damage and repair studies, with T4 endonuclease and similar assaysDamage density tracks dose, so repeat experiments need the same dose
Photocrosslinking and photoactivationPsoralen crosslinking, photoaffinity labelling, protein-nucleic acid crosslinkingUsually run at the 365 nm long-wave band, where energy is lower and biomolecular damage is smaller

One positional difference is easy to miss: a crosslinker performs uniform irradiation of a batch inside an enclosed chamber, rather than a quick pass with a lamp. The mirror-finish stainless steel walls and the aluminium diffuser plate help keep the centre and the edge of a membrane at similar levels, and the sensor sits above the irradiation chamber rather than in a corner so that its sampling position is more representative. All of this exists to make "the same batch of samples receives the same irradiation" true.

2. How to choose a UV crosslinker

Selection does not need to be complicated. Six checks in order are enough, and the opening two decide the outcome.

1. Settle the wavelength before anything else

The wavelength follows from what you need to excite or to cut; choose the wrong one and everything downstream is void. One model usually exists in several wavelength versions, and the difference is not an accessory but the emission lines of the lamps:

WavelengthBandSuited to
254 nmUV-CNucleic acid membrane crosslinking (the default choice), PCR decontamination, UV sterilization, UV mutagenesis, pyrimidine dimer induction
302 nmUV-BMilder than 254 nm with less nucleic acid damage; for cases that need long-wave exposure while limiting photodamage
365 nmUV-APhotosensitizer activation (psoralens), photoaffinity labelling, photocrosslinking of some proteins and biomolecules

Why 254 nm is the default in molecular biology labs: nucleic acid bases absorb around 260 nm, and 254 nm sits next to that peak, so excitation of pyrimidine bases to form dimers, and covalent bonding between nucleic acid and membrane, are relatively efficient. The cost is that this is UV-C, with higher risk to eyes and skin.

2. An energy (dose) mode is required, not just a timer

This is the check that really separates classes of instrument. Crosslinking depends on how much energy the sample actually receives; time is merely one way of arriving at a dose. UV lamps decay with hours of use, and supply voltage and ambient temperature drift, so "30 seconds" on a new lamp and on a two-year-old lamp can differ by a wide margin - and nothing on the outside shows it. It appears as hybridization signal that weakens year after year and background that climbs year after year.

A machine with an energy mode monitors chamber intensity in real time through a sensor and integrates intensity over time, stopping when the set value is reached: a dim lamp runs a little longer, a strong lamp stops early. All three models here offer this; they differ in range and in how you operate them. The UCL-3200 and UCL-3500 use a 0-9.999 J/cm² energy mode with 9 preset programs recalled by one key; the UVP CL-3000 offers a 0.1-9999.9 mJ/cm² energy mode plus a time mode.

3. Chamber size and power follow your sample load

The chamber decides how many membranes fit in one run. The UCL-3200 has a 32×26×15 cm chamber with 6 × 8 W lamps, suited to a single membrane or small batches; the UCL-3500 is a 6 × 15 W high-power unit with a chamber in the 44×34×15 cm class, able to lay out several membranes and large gels; the UVP Crosslinker CL-3000 uses 6 × 8 W lamps in a 6.8 kg body and is a compact model. Lamp power affects how long a target dose takes; for labs that run blots in batches, power and chamber size matter more than a peak intensity figure.

4. Uniformity and sensor protection

Uniformity decides whether the centre and the edge of one membrane match. Two things to look at: whether the walls combine specular and diffuse reflection (the mirror stainless steel plus aluminium diffuser of the UCL series is one example), and whether the sensor has a quartz window and sits in a representative position. Once a sensor is corroded or contaminated by chemicals, even precise energy integration is built on a wrong basis.

5. Operating and safety design

Details worth confirming: whether the lamp cuts out when the door opens, whether there is a viewing window and a door lock (the UVP CL-3000 is a door-type unit with a viewing window), whether the unit goes to standby when the run ends, and whether it returns to the last program at power-up. These are not gimmicks - running unattended and opening the door on guesswork are the actions that cause accidents and failed experiments.

6. Service and consumables

UV lamps are consumables and decay is unavoidable. Confirming the lamp model, the replacement interval and local spare stock affects long-term use more than a peak number on a datasheet.

3. How a UV crosslinker differs from an oven

Both can fix nucleic acids to a membrane, but the mechanisms are entirely different. They do not replace each other, and they should not be treated as two options at different budgets.

ItemUV crosslinkerOven (vacuum or forced-air baking)
Fixing mechanismUV excites bases to form covalent bonds, welding nucleic acid to the membrane matrixHeat dehydrates membrane and nucleic acid, fixing by adsorption and partial crosslinking
ReachEffective where light reaches, a surface effectWhole item heated, inside and out
TimeTens of seconds to a few minutesTypically 1-2 hours, plus heating and cooling
Controllable parameterDose (mJ/cm² or J/cm²), recordable and checkableTemperature and time, dependent on membrane thickness, load and airflow
Side effects on the sampleExcess UV breaks nucleic acid and lowers hybridization signalHigh temperature can make fragile RNA or small fragments degrade more visibly
MembranesNylon and nitrocellulose both workNitrocellulose often needs baking as a support step; nylon can use UV alone

In practice the division of labour is usually: nylon membranes are crosslinked with UV, where dose is adjustable and the step is fast; nitrocellulose membranes get UV plus baking, or follow the membrane supplier's baking protocol. Some protocols do both steps, UV followed by low-temperature baking, stacking two mechanisms to improve retention.

Conversely, an oven cannot deliver a dose figure. It offers temperature and time, while the heat a membrane actually receives depends on load and airflow, which is hard to align strictly between batches. If your protocol needs crosslinking conditions written into an SOP and compared across batches, an oven is not a suitable metering tool.

4. What can stand in for a UV crosslinker

The conclusion up front: there are few situations where a substitute works, and most substitutions merely move the uncontrolled variable somewhere else. The boundaries are set out below, substitute by substitute.

The UV lamp in a clean bench or biosafety cabinet

This is among the more frequently tried substitutes. It does emit 254 nm and it does fix nucleic acid on a membrane to some degree, but three things are missing: no dose metering (you do not know how much exposure was given), uneven intensity distribution (lamp position and distance decide everything, and a membrane placed off-centre gets a different dose), and no reproducibility (lamp age, switching cycles and voltage all vary). It is acceptable for qualitative pilot work, not for quantitative results headed for a paper.

Handheld UV lamps and UV transilluminators

A transilluminator is built for gel viewing; its light path and uniformity are designed for reading bands, not for giving a membrane an even dose. Handheld lamps are worse: distance depends on the hand and dose on counting seconds, so repeatability is essentially absent. Both suit a quick check before loading a gel, not a crosslinking step.

Baking (oven or vacuum oven)

This substitutes a different mechanism for the same purpose, and is common with nitrocellulose. It is not crosslinking but fixing by dehydration and adsorption; the result is sensitive to membrane type and baking conditions, and it also cannot give a comparable dose figure. It suits methods that already have a mature baking SOP and do not need dose records.

UV irradiation chambers

An irradiation chamber (such as the LUYOR-3550) looks similar to a crosslinker and also has a chamber and closed-loop dosimetry; the difference is positioning. The chamber is larger (68×55×32 cm class), there are more lamps (20 × 15 W), irradiance is expressed in mW/cm², and the intended samples are cells, animals and materials that need large-area uniform irradiation, usually in the UVA/UVB bands. Using one for membrane crosslinking is physically possible, but it is a large machine for a small job, and you would need to verify the 254 nm band and the sample position yourself.

If the goal is a small qualitative experiment inside a budget, a substitute can be used; but as soon as results have to be repeated or written into a paper or report, the dose has to be recordable, and at that point there is no substitute. That is where the real value of a crosslinker lies: it turns "irradiated for a while" into "received 120 mJ/cm²".

5. How to judge crosslinker brands

"Which brand is good" is a question that has to be split, for crosslinkers, into "which class of machine suits your experiments" and then into brands. Three sources are common in labs today:

  • UVP (now part of Analytik Jena): the CL-1000 series was standard equipment in many older labs, and the CL-3000 is its successor, with 254/302/365 nm versions, energy and time modes, and a built-in sensor that compensates for lamp ageing. Most dose conditions cited in the literature were established on this platform, which makes method transfer easier to align.
  • LUYOR UCL series: the UCL-3200 (6 × 8 W, 32×26×15 cm chamber) and UCL-3500 (6 × 15 W, large chamber) follow the same dose logic - microprocessor integration in real time, 9 presets, mirror plus diffuse chamber. The supply chain is domestic, so accessories and service respond quickly, which suits labs that run blots in batches with several units.
  • Other imported brands: models that sell on chamber uniformity and degree of automation, usually at a higher price, for institutions with strict metrology requirements or audit traceability.

When judging, look at four things rather than at the larger number on a datasheet:

  1. Whether the energy mode is genuinely closed-loop: real-time sensor integration, or time converted from a nominal power figure. The former is what compensates lamp ageing.
  2. Sensor position and protection: sampling from above under a quartz window beats a bare sensor hidden in a corner.
  3. Written data on chamber uniformity: a supplier who can provide factory test records is more credible than one who writes "good uniformity".
  4. Lamp and spare-part supply: lamps are consumables, and whether the same model can be bought years from now decides whether the machine still works in five years.

One more note: the gap between brands is often less important than whether the method is aligned. If you keep the old seconds after changing machines instead of keeping the dose, the results will not match - and that affects experimental success more than the brand choice.

6. How to use a UV crosslinker

Taking a routine nucleic acid membrane crosslinking run as the example, the full sequence is below. Key layouts differ between models, but the order is the same.

Power-up and parameter check

After power-up most models return to the last program used (the UCL series does), so confirm three things: the wavelength version is the one you want (254, or 302/365), whether the unit is in energy or time mode, and whether the set value matches today's protocol. The dose figure should come from the membrane datasheet or from a gradient experiment validated in your own lab, not from someone else's number.

Settling the dose

120 mJ/cm² is a widely circulated reference value, coming from some commercial nylon membranes and classic Northern protocols, and many manufacturers ship it as a factory preset. It is not a universal answer: recommended conditions differ between membrane brands and types, nitrocellulose usually needs about 20%-30% more than nylon or a baking step, RNA degrades more readily than DNA so the dose should be on the low side, and wet versus dry membranes and different transfer buffer systems all shift the suitable value.

The safe route is three steps: start from the value recommended by the membrane or reagent datasheet → run a gradient pilot (for example 50/100/150/200 mJ/cm²) → take the setting with strong signal and no visible degradation as your lab's routine value, and record the dose, the membrane brand and model, and the cumulative lamp hours.

Placing the sample

Three actions are worth more than buying a more expensive membrane: lay samples flat in a single layer with the sample side up, as close to the centre of the chamber as possible; do not overlap, since overlapping areas receive almost no dose in the shadow; and drain surface buffer after transfer and crosslink while the membrane is still slightly wet, rather than waiting for it to dry. A membrane that dries out before crosslinking is a common cause of "the signal mysteriously got weaker".

Running and finishing

Close the door, start, and wait for the program to end on its own. A machine in energy mode stops when the set dose has accumulated, beeps, and then goes to standby. Do not open the door mid-run - it interrupts dose integration and lets UV escape. Confirm the lamp is off before removing the membrane.

Recording and review

Write the dose, wavelength, membrane brand and model, nucleic acid type and cumulative lamp hours into the lab record. Six months later, when you are working out why this batch gave a weak signal, that set is close to the sole usable evidence you will have. It is also what it means to treat crosslinking dose as a parameter of the same rank as annealing temperature - it is an experimental parameter, not an operating habit.

Details that come up again and again

How do I tell under-crosslinking from over-crosslinking?

Under-crosslinking shows as a generally weak signal after washing and long incubation, with a tendency for nucleic acid to come off the membrane; typical supporting evidence is that re-exposing the dried membrane under the same conditions visibly improves the signal. Over-crosslinking shows as signal dropping and background rising at the same time, with bands looking soft and smeared, and higher molecular weight fragments affected more. The two call for opposite troubleshooting, so separate them before adjusting anything.

How often should lamps be replaced?

There is no universal calendar interval. A machine in energy mode compensates for decay automatically, so "it still works" cannot be judged by brightness alone. A workable method is to measure irradiance at the same position at intervals, or run a standard sample, and watch whether the time needed to reach the same dose clearly lengthens; when it lengthens enough to affect your throughput, that is the signal to replace.

Can proteins or other biomolecules be crosslinked?

Yes, but the dose is usually higher than for nucleic acids (a common reference is 150-300 mJ/cm², optimized by gradient for the molecule and system), and the wavelength has to be right: most protein photocrosslinking runs at the 365 nm long-wave band with a photosensitizer. Applying the nucleic acid figure of 120 mJ/cm² directly will usually not fix them.

What are the safety points?

254 nm is UV-C and carries more risk to eyes and skin than UVA. The door interlock and automatic shut-off are the basic line of defence; do not look into the chamber, and do not start a run with the door not fully closed. Where samples need long adjustment, wear protective glasses rated for the band. UV inside the chamber looks "dim", which is exactly why it is easy to underestimate.

Can one machine cover both 254 nm and 365 nm?

Crosslinkers ship as wavelength versions, and 254 nm and 365 nm use lamp sets with different emission lines; most models cannot change band in the field, and the few dual-wavelength models require you to confirm that the two lamp sets are controlled independently. Set the version by your main use at purchase - 254 nm for membrane crosslinking and PCR decontamination, 365 nm for photosensitizer activation. Planning a later retrofit is neither economical nor friendly to factory validation.

Is baking or washing needed after crosslinking?

A nylon membrane can go straight into prehybridization after UV crosslinking, with no further baking; nitrocellulose usually needs a low-temperature bake added per its datasheet. There is no need to wash after crosslinking, but let the membrane air-dry before hybridization - residual buffer on the surface raises background and makes the membrane stick inside the hybridization bag.

Selection quick reference

Your situationSuggested direction
Routine Southern/Northern membrane crosslinking, one membrane or a fewA 254 nm model with energy mode and presets, chamber large enough for one membrane (such as the UCL-3200)
Batch blot work needing several membranes or large gels laid out at onceLarge-chamber, high-power model (such as the UCL-3500)
Following literature methods and needing to align with older dataA model on the same platform as the literature (such as the UVP Crosslinker CL-3000 class)
Photosensitizer activation, photoaffinity labelling365 nm long-wave version
Gentle irradiation with controlled photodamage302 nm UV-B version
Large-area uniform irradiation of cells, animals or materialsNot a crosslinker; choose a UV irradiation chamber by UVA/UVB band and chamber size

If you are unsure about the wavelength version or the dose range, tell us the membrane type, the nucleic acid (DNA/RNA) and whether the next step is hybridization, amplification or photoactivation, and we will advise on method rather than on price. Related products and technical material are on the UVP Crosslinker CL-3000 page, or see the UV crosslinker section.

Related sections and models

This article sits in the frequently asked questions section.

Other sections on the same product line include UV crosslinkers (dose set in J/cm², the figure that matters for both nucleic acid crosslinking and materials curing), UV radiometers (measuring mW/cm² intensity and J/cm² accumulated energy, which is how lamp compliance is judged), and life science instruments (the entry point for fluorescence imaging, UV crosslinking, UV transmission and cell irradiation).

Models mentioned: UCL-3200, UCL-3500, UVP CL-1000. Ranges, accuracy and accessory lists for each model are on the product pages.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top