Xinysun Instrument (Shanghai) Co., Ltd.

Products

PRODUCTS

Breadcrumb: Home > Products > Life Science Instruments > UV Crosslinkers

UCL-3500 UV Crosslinker
  • UCL-3500 UV Crosslinker

  • UCL-3500 UV Crosslinker

  • UCL-3500 UV Crosslinker

UCL-3500 UV Crosslinker

Overview

UCL-3500 UV crosslinker: 6x15 W lamps, 44x34x15 cm chamber, 0-9.999 J/cm2 energy mode and 9 presets for reproducible nucleic acid membrane crosslinking.

Model:LUYOR UCL-3500
Updated:2026-11-13
Manufacturer:LUYOR
Reference price:Request a Quote
Views:
DetailsSend inquiry
6 × 15 WAbout twice the power · same dose, reached faster
44×34×15cm chamber · several membranes per run
254 nmUV-C · 302/365 nm versions available
0–9.999J/cm² energy mode · reproducible dose
9preset programs · last settings restored at power-up
3-yearfree warranty (free replacement within 1 year)

Start with one decision: UCL-3500 or UCL-3200

On the UV crosslinker section of this site, the question we hear most about these two units is "which one should I buy". The easy misunderstanding is this: the specifications shown on the page look like a difference in size only, but the control logic, chamber construction and operating method are identical.What actually decides the choice is how many samples you process in one run.

The UCL-3500 differs from the UCL-3200 in exactly two respects: lamp power (6×15 W versus 6×8 W, close to double) and chamber volume (internal 44×34×15 cm versus 32×26×15 cm - about 80% more footprint at the same height). Everything else - microprocessor energy integration, 9 presets, power-up memory, end-of-cycle beep, three-year warranty - is the same on both.

Item UCL-3200 UCL-3500 (this page)
UV lamps 6 × 8 W 6 × 15 W (about twice the power)
Internal chamber (L×W×H) 32 × 26 × 15 cm 44 × 34 × 15 cm (about +80% area)
External dimensions (L×W×H) 34 × 35 × 31 cm 55 × 36 × 30 cm
Typical UV intensity (254 nm) approx. 3,500-5,500 μW/cm² (distributor figure) approx. 5,500-6,500 μW/cm² (distributor figure)
Energy / time setting Both: 0.000-9.999 J/cm² (or 0.00-99.99); 00.00-99.59 min (or 000.0-599.5)
Preset programs 9 9
Weight 10 kg 10 kg (site and official figures agree)
Warranty Free replacement within one year, three-year free warranty; both CE marked
Best for Single membranes, samples up to A4, routine-throughput labs Multiple membranes, large gels, 96-well plate samples, high-throughput or high-sample-volume labs
One shortcut for the decision:work out the maximum number of samples you need to process at the same time. If the answer is one membrane or one or two gels, the power difference only shows up as "tens of seconds versus one or two minutes" and is not worth paying extra for. If the answer is "a batch of a dozen membranes" or "one full-size gel", the UCL-3500 saves real labor and batch-management cost. A lab whose sample volume is growing, or that may move to higher throughput, is usually better off buying the UCL-3500 now than buying small first and replacing later.
One counterpoint: bigger does not mean simpler.With a larger chamber, edge effects become more visible - the irradiance difference between the center and the edges is greater than in a small chamber, and energy mode only guarantees that the set dose is received at the sensor, not at every position. When you use the UCL-3500, keep samples as close to the center as possible and at a consistent position from batch to batch; otherwise "same method, results that do not match between batches" becomes your problem. Details in the next section.

The cost of a large chamber: edge effect and sample placement

One design goal of any UV crosslinker is irradiance that is as uniform as possible inside the chamber, and every established manufacturer designs for it. But uniform is relative, not absolute: positions directly under the lamps near the center are usually stronger, and the closer to the edge the weaker it gets. In UV irradiation literature this is usually called the edge effect.

The UCL-3500 addresses this with two structural measures: the irradiation chamber is an aluminum-alloy cavity, and it is fitted with an aluminum diffuse reflector - direct and reflected light add together so irradiance at different positions is as close as possible. The UV sensor is mounted above the chamber rather than in a corner, so the sampling position is more representative, and a quartz glass shield keeps chemicals from contaminating or aging it.

1. Chamber and reflector design

Aluminum-alloy UV chamber plus an aluminum diffuse reflector. Direct light combined with reflected light keeps UV intensity across the chamber as even as possible - uniformity determines whether the center and the edge of the same membrane give the same result.

2. Sensor position and protection

The UV sensor unit sits at the top of the chamber rather than in a corner, so its reading is more representative. A quartz glass shield prevents chemical corrosion and contamination - once a sensor has drifted or been contaminated, even an accurate energy mode integrates on a wrong basis.

3. Energy integration control

A programmable microprocessor monitors UV intensity continuously and stops the exposure the moment the accumulated energy reaches the set value. Lamp aging that lowers UV output does not change the delivered dose - this is what makes energy mode possible.

Three habits you need with a large chamber

  1. Keep samples in the center region, not against the walls. The larger the chamber, the bigger the difference between center and edge.

  2. Use the same position for every run of an experiment. Do not put one batch in the middle and the next at the edge - that turns the same dose setting into different real doses, and it is a hidden reason many labs cannot reproduce results.

  3. Single layer, sample side up, no overlap. Samples under an overlap receive almost no dose, and heat builds up there.

For experiments with high reproducibility requirements, do a position audit:measure irradiance at a set of fixed points inside the chamber with an external UV meter and record the values in the instrument log.You then know the actual intensity in the area you normally use, and you can quickly check after a lamp change whether uniformity has shifted.See the full range of UV meters →  

Energy mode: turning "how long" into "how much dose"

Start with the conclusion: crosslinking depends on how much UV energy the sample actually receives (dose, in mJ/cm² or J/cm²), not on how long it is exposed.Time is only the means to a dose; the dose is the result. This is especially easy to overlook on the UCL-3500 - because the unit is powerful and fast, "30 seconds" looks like enough, which makes it easier to give up dose thinking.

The risk in time mode is that UV lamps decline continuously with use, and ambient temperature and line voltage also fluctuate, so "30 seconds" from a new lamp and from a lamp that has run for two years can differ by a wide margin. And that change is completely invisible from the outside - you only notice that hybridization signal gets weaker every year and background gets higher, without finding the cause.

The UCL-3500 works the same way as the UCL-3200: during exposure a microprocessor monitors UV intensity in the chamber in real time and integrates it over time, stopping automatically when the set dose is reached.Dimmer lamps get a longer exposure, higher intensity stops earlier - whatever the lamp output does, the irradiation energy can be reproduced.

Item Time mode Energy mode (the core of the UCL-3500)
What you set Exposure duration (e.g. 30 s) Accumulated dose (e.g. 120 mJ/cm²)
When lamps age Dose drops, and you cannot see it Exposure extends automatically, dose unchanged
Line / temperature fluctuation Directly affects dose Absorbed by the integrator, dose unaffected
After new lamps Conditions must be re-established Setpoints remain valid, no recalibration
Best for Aligning to fixed times in older literature; sterilization protocols judged by time Nucleic acid membrane crosslinking, PCR decontamination, UV mutagenesis - anything dose-dependent
One set of publicly available parameters:to immobilize DNA on a nylon membrane in Southern blotting, UV energy is usually set to 0.12 J/cm² (= 120 mJ/cm²), which on a high-power model takes about 20-40 seconds. Treat this as a starting point, and confirm it against the instructions for the membrane roll you actually have - recommended conditions differ between membrane brands.

Choosing among three wavelengths: 254 / 302 / 365

The UCL-3500 series offers three wavelength versions of the same chassis; the choice depends on what you need to excite, not on which one costs more.

Model Wavelength Band Typical use
UCL-3500
This page
254 nm UV-C Membrane crosslinking and immobilization of nucleic acids (Southern/Northern/Dot/Slot blot, EMSA); eliminating PCR contamination and UV sterilization; UV-induced mutagenesis (UV breeding); E. coli RecA mutant screening; pyrimidine dimer induction and related restriction digestion experiments
UCL-3500M 302 nm UV-B Gentler than 254 nm with less damage to nucleic acids; suited to experiments that need longer-wavelength irradiation or activation while keeping photodamage under control
UCL-3500L 365 nm UV-A Photosensitizer activation (e.g. psoralen crosslinking), photoaffinity labeling, photocrosslinking of some proteins and biomolecules - long-wave energy is low and does not directly damage DNA to any appreciable extent
Why 254 nm is the default in molecular biology labs:nucleic acid bases absorb with a peak near 260 nm, and 254 nm sits right next to that peak, so it efficiently excites pyrimidine bases to form dimers and drives covalent bonding between nucleic acid and membrane - the physical basis of both crosslinking and decontamination. Because the biological effect is strong, 254 nm is UV-C and carries higher risk to eyes and skin (see the safety notes below).

If you are unsure, fix the wavelength first, then the capacity: wavelength follows the experiment (what you crosslink, what you excite), capacity follows sample volume (how many membranes per run).Send us your protocol and per-run sample count and we will advise.

Workflow: six steps for a standard crosslinking run

The UCL-3500 offers energy mode, time mode and preset mode, plus 9 stored programs. The sequence below covers a routine membrane crosslinking run:

1
Confirm status and dose

At power-up the instrument returns to the settings it had before shutdown. First confirm whether this run uses energy modeor time mode, and check that the dose value matches the protocol (for example 120 mJ/cm²).

2
Plan the sample layout

Lay out the samples for this run by size and keep the whole group in the center region, with gaps between them and no overlap; membranes flat in a single layer, sample side up. On a high-power model, hold the "centered" rule even more strictly - the chamber is large and the difference between edge and center is obvious.

3
Close the door and start the exposure

Start only after the door is fully closed. During exposure do not open the door, and do not look into the chamber to check whether the lamps are on - read the display instead.

4
Wait for the automatic stop

In energy mode the instrument integrates in real time and stops with a beep when the set dose is reached. Note: as lamps age and ambient temperature changes, the time needed for the same dose gradually increases - if one exposure takes noticeably longer than usual, that is a signal worth recording and worth checking lamp output for.

5
Remove samples and record

When the run ends the instrument goes to standby. Remove the samples and record the dose, the mode used, the membrane brand and model, the accumulated lamp hours, and the sample position. Record these together, so you have a basis for backtracking if a problem appears later.

6
Store validated conditions as a preset

If the conditions are validated by the experiment, store them in one of the 9 presets and label the purpose (e.g. "nylon membrane · DNA · 120 mJ"). This step turns individual experience into a lab asset and is the easy way to reduce batch-to-batch variation.

One point on the energy and time setting ranges needs explaining:the site specifications give energy 0.000-9.999 J/cm²(or 0.00-99.99) and time 00.00-99.59 minutes(or 000.0-599.5, read as minutes plus decimal); a few distributor listings give energy as 0.025-9.99 J and time as 10 s-599 min, which does not fully match. For actual operation, follow the keypad instructions in the manual supplied with the unit; if you are unsure, energy mode avoids the unit-interpretation question entirely - one reason we recommend energy mode for routine work.

Three typical applications: how to get usable results

Application 1: membrane crosslinking and immobilization of nucleic acids (Southern / Northern / Dot / Slot blot, EMSA)

This is the design home of the instrument, and where a large chamber shows its value directly. DNA reaches the membrane surface by electrophoresis and transfer, then 254 nm UV is used to form a stable bond between nucleic acid and membrane, so the nucleic acid is retained through prehybridization, long incubations and washes. Key points:

  1. Crosslink immediately after transfer and keep the membrane slightly wet - do not let it dry out; crosslinking efficiency drops noticeably once the membrane is dry, and this is often misdiagnosed as "not enough dose"

  2. Single layer, sample side up, kept in the center region, no overlap, not against the walls

  3. Set the dose from the membrane/reagent instructions, and run a gradient pilot if needed. One advantage of a large chamber: you can expose different regions of the same membrane to different doses and get a dose gradient in one run

  4. Record dose, position and lamp hours; store validated conditions as a preset program

Related work includes membrane crosslinking for EMSA (gel shift): the crosslinking step follows transfer, typically at 254 nm for several tens of seconds at the dose recommended by the membrane instructions. If crosslinking is poor and even the free-probe band is weak, a second crosslinking pass under the same conditions after drying the membrane can be tried - but only after confirming that a dried membrane is not the cause, otherwise it just hides the problem.

Application 2: eliminating PCR contamination and UV sterilization (with one trap that has to be explained)

The principle holds: 254 nm UV makes DNA form pyrimidine dimers, the polymerase cannot read through them, and the contaminant is no longer a valid template. Published work reports that this inactivation can reduce residual template in a tube by more than 1000-fold, which makes it one of the classic ways to control false positives in PCR.

But while UV destroys contaminating DNA, it also damages other components of the reaction, and this side effect is often ignored:

Component Sensitivity to UV Practical consequence
Taq DNA polymerase Highly sensitive Activity drops after exposure, and PCR sensitivity drops with it
Primers Sensitive, and sequence-dependent Primers with adjacent thymines are damaged more readily; results vary widely between primer sets
dNTPs Relatively UV-resistant, but absorb 254 nm strongly They sit in front of the DNA and shade it, so decontamination efficiency falls sharply and longer exposure is needed
Tube plastic Most materials absorb UV The same instrument with different tubes and distances gives very different decontamination results
So the correct approach is:
1. Do not treat UV exposure as a general method for "irradiating the whole reaction mix".If enzyme and primers are already in the tube, exposure directly reduces sensitivity (reported up to 10-fold).
2. Appropriate targets for UV treatment are: bench surfaces, pipettes, tube racks, and reagents and consumables that contain no enzyme or primers.
3. If you do use the classic "irradiate the reaction mix" strategy, then: add enzyme and primers after exposure, validate sensitivity separately for each PCR system, and keep tube type and position fixed.
4. The more robust direction is aliquoting reagents, using filter tips to control aerosols, and adopting UNG/dUTP systems - UV decontamination works better as an auxiliary measure.
5. One more note: UV sterilization acts on surfaces, and has limited effect inside solutions, in shadowed areas at the bottom of a tube, or where organic material shades the surface.

Application 3: UV mutagenesis, sterilization and photochemical crosslinking

UV-induced mutagenesis (UV breeding)

254 nm exposure of cell suspensions or spore suspensions produces random mutations. These experiments demand dose reproducibility - dose determines mutation rate and survival rate, and "how long" cannot be aligned between batches. Fix the dose and pair it with a survival curve.

RecA mutant screening / pyrimidine dimers

E. coli RecA mutant screening, pyrimidine dimer induction, and gene mapping based on dimer-blocked cleavage all assume a stable UV dose. These experiments suit energy mode, with the dose written into the methods section.

Biomolecule crosslinking / photosensitizer activation

Protein and biomolecule crosslinking usually needs a higher dose than nucleic acids (start gradients around 150-300 mJ/cm²); for psoralen-type photosensitizer activation or photoaffinity labeling, choose the 365 nm UCL-3500L - long-wave energy is low and does not directly damage DNA to any appreciable extent.

Same-category comparison: UCL-3500 / UCL-3200 / UVP CL-3000

The UV crosslinker section of this site currently offers three models, with clear differences in positioning:

Model Brand Lamps Chamber (internal) Energy / dose Positioning
UCL-3500
(this page)
LUYOR (USA) 6 × 15 W 44×34×15 cm
Complete unit 55×36×30 cm / 10 kg
Energy 0-9.999 J/cm²
Time 0-99.59 min
9 presets
High capacity and throughput: several membranes, large gels and multiple sample groups in one run; less time needed for the same dose
UCL-3200 LUYOR (USA) 6 × 8 W 32×26×15 cm
Complete unit 34×35×31 cm / 10 kg
Energy 0-9.999 J/cm²
Time 0-99.59 min
9 presets
The routine lab workhorse: one membrane, one gel, samples up to A4; all three wavelength versions available; a good balance of cost and versatility
UVP / Analytik Jena
CL-3000
UVP (USA)
(Analytik Jena)
6 × 8 W (254 nm) 35×27×16 cm
Complete unit 41×40×26.5 cm / 6.8 kg
0.1-9999.9 mJ/cm²
(0-10 J/cm²)
Time 000:01-999:59
Imported-brand reference model: real-time UVC dose monitoring, a door window that lets you watch the run while blocking UV, and a safety door lock; compact and lighter
Suggested order of decision:1. Fix the wavelength - 254 nm for nucleic acid crosslinking, PCR decontamination and UV mutagenesis; 365 nm for photosensitizer activation and photocrosslinking. 2. Then look at sample volume - UCL-3200 for samples up to A4, UCL-3500 for multiple membranes, large gels or high batch counts. 3. If your organization has an established brand preference, or the quality system already lists a UVP/Analytik Jena asset number, choose the CL-3000. All three follow the same approach to temperature control and uniformity (metal chamber, reflector, internal sensor); what really separates them is power, chamber size and budget.

Specifications

Listed below for the UCL-3500. Differences between the three wavelength versions are noted separately - please confirm the wavelength before ordering:

Parameter UCL-3500 UCL-3500M UCL-3500L
Wavelength 254 nm 302 nm 365 nm
UV lamps 6 × 15 W 6 × 15 W 6 × 15 W
Programming 9 preset irradiation energy values
Energy 0.000 to 9.999 J/cm² or 0.00 to 99.99 J/cm²
Time 00.00 to 99.59 min or 000.0 to 599.5 min
Temperature (operating environment) 15 ℃ - 35 ℃ (some distributors list 5-33 ℃)
Humidity 70%, non-condensing
Housing surface temperature ≤ 30 ℃
Start-up time < 1 s
External dimensions (L×W×H) 55 cm × 36 cm × 30 cm
Internal dimensions (L×W×H) 44 cm × 34 cm × 15 cm
Weight 10 kg
Power supply 230 VAC 50/60 Hz
Certification CE
Model UCL-3500 (254 nm, this page); the same chassis is also available as UCL-3500M (302 nm) and UCL-3500L (365 nm)
Product type Microprocessor-controlled UV irradiation system / UV crosslinker
Brand / manufacturer LUYOR, USA (per the product field on this site; the series is LUYOR's UV crosslinker line)
Control method A programmable microprocessor monitors UV intensity in real time; exposure stops automatically when the irradiation energy matches the preset value, so irradiation energy is reproducible regardless of lamp output fluctuation
Operating modes Energy mode, time mode, preset mode; 9 preset programs
Irradiation chamber Aluminum-alloy UV chamber plus aluminum diffuse reflector, keeping UV intensity uniform inside the chamber
UV sensor Located at the top of the irradiation chamber with a quartz glass shield, protecting it from chemical contamination and ensuring long-term durability
Power-up and alerts At power-up the instrument returns to the settings used before shutdown, one-key operation; a beep signals the end of crosslinking and the unit goes to standby without further input
Warranty Free replacement within one year, three-year free warranty
Main applications Membrane crosslinking and immobilization of nucleic acids (Southern/Northern/Dot/Slot blot, EMSA); eliminating PCR contamination and UV sterilization; UV-induced mutagenesis; RecA mutant screening in E. coli; biomolecule crosslinking; DNA nicking in agarose gels; restriction enzyme digestion related to pyrimidine dimers
Notes on figures (please check before ordering):
1. Weight: this page and the original site page use 10 kg; some distributor listings give 12 kg or 13.8 kg (26 lb). If the figure goes into a purchase contract or an asset register, use the parameter page of the manual supplied with the unit.
2. Operating temperature: this site and most distributors state 15-35 ℃; a few state 5-33 ℃.
3. Lower limits for energy and time: this site states 0.000 J/cm² and 00.00 min; a few distributors state 0.025 J/cm² and 10 s.
4. Chamber material wording: the original site page and official material describe an "aluminum-alloy UV chamber with aluminum diffuse reflector"; the UCL-3200 uses a mirror-finish stainless steel chamber - same design approach, different material wording.
5. UV intensity: 5,500-6,500 μW/cm² (254 nm) is a figure published by distributors; the original site page does not give it, and this page states the source as it is.
The above are manufacturer-stated parameters and may vary between batches; the manual supplied with the unit and the factory calibration data take precedence. For a formal datasheet, please contact us to request one.

Consumables and calibration: dose is bought, and it also has to be managed

Two things on a UV crosslinker have to be handled as consumable management, otherwise the instrument looks fine while results drift:

  • Lamps: UV output from a lamp declines continuously with use, and the common replacement criterion in the industry is output down to about 70% of the initial value - at that point the lamp still lights, and because of energy integration the dose you set is still delivered and everything looks correct, only the time needed keeps growing.Record accumulated hours and watch for the signal "is the time for the same dose clearly longer".The UCL-3500 uses six lamps of the same service life; replace the whole set together to preserve uniformity.

  • Quartz shield and chamber reflector: contamination on the quartz shield and dust or residue on the reflector both change the actual irradiance distribution.Clean regularly with a soft cloth and a suitable cleaner; do not scrape with anything abrasive.See the XRP-3000 UV/white light meter →

    One reminder:if your lab has to pass a CMA/CNAS assessment or a customer audit, build "energy integration + periodic external verification + lamp replacement records"into a logbook.That is far more solid than a single claim that "the instrument is traceable" - auditors look at records, not at brochures.

Frequently asked questions

Where do the UCL-3500 and UCL-3200 differ?Do I need the large-chamber version?

The control logic is identical on both units: microprocessor energy integration, reflector-lined chamber, 9 presets, end-of-cycle beep, three-year warranty.There are only two differences.First, lamp power: the UCL-3200 has six 8 W lamps, the UCL-3500 six 15 W lamps, close to double.Second, the chamber: 32×26×15 cm internal on the UCL-3200 versus 44×34×15 cm on the UCL-3500, about 80% more area.So the decision is direct: if you process one membrane or one or two gels per run, with samples up to A4, the UCL-3200 is fully sufficient - crosslinking takes tens of seconds to a few minutes either way, and the power difference only changes how long that takes; if you lay out several membranes at once, a full-size gel or a 96-well plate, or your sample volume is large and you want to cut waiting time and batch count, the UCL-3500 is built for that case.One more point: the larger the chamber, the more visible the difference between edge and center, so placement discipline matters more, not less - it is not "bigger means less work".If you are unsure, send us your sample size and count per run; judging by actual workload is more reliable than judging by power.

Higher lamp power - will it heat and damage my samples?

This is a common concern when choosing a high-power model.Higher lamp power does mean more UV energy per unit time reaching the sample, and a slightly higher heat load inside the chamber; but crosslinking dose is accumulated, so higher power means less time to reach the same dose - total exposure time shrinks, and the two effects partly cancel.What actually decides whether a sample warms up is the total delivered energy and the sample's own UV absorption, not lamp power alone.Practical advice: 1.Set the dose from the protocol; do not raise it just because the unit is powerful.2.For temperature-sensitive work (samples that must stay active, enzyme-containing systems), start low and set energy mode to the minimum dose that works.3.The housing surface is rated at no more than 30 ℃ and the chamber is an enclosed space; if sample temperature matters, run one dummy or surrogate exposure under the same conditions first and confirm the temperature rise is acceptable before running real samples.4.Keep samples in a single layer, no stacking - stacked areas are both shaded and prone to heat build-up.If your experiment is very temperature-sensitive, tell us the system and target dose and we will help you weigh the UCL-3200 against the UCL-3500.

Is the dose the same at the center of the chamber and at the edge?

No, because irradiance uniformity is limited.UV intensity inside any UV crosslinker is not exactly equal everywhere: positions directly under the lamps near the center are usually stronger, and it falls off toward the edges - the edge effect.In a small chamber the samples sit close to the center anyway, so the difference is not obvious; once the chamber is 44×34 cm, "center" and "corner" can differ by a substantial margin.Energy mode reads the intensity at the sensor position, so it guarantees that the sensor receives the set dose, not that every sample position does.With the UCL-3500, keep three habits: 1.Put samples in the center region, not against the walls.2.Use the same position for every run of the same experiment.3.If reproducibility is critical, measure irradiance at a few fixed points with an external UV meter, confirm the actual difference in the area you normally use, and record it.Note that this site does not publish a quantified uniformity figure for this model; for written data, ask us for the factory test records.

What is the difference between energy mode and time mode, and which should I use?

Use energy mode whenever the result depends on dose.Crosslinking depends on how much UV energy the sample actually receives (dose, in mJ/cm² or J/cm²), not on exposure time.Time mode has a problem: lamps decline with use, and ambient temperature and line voltage fluctuate - "30 seconds" from a new lamp and from a lamp used for two years can give very different doses, and that change is invisible externally.You only notice hybridization signal weakening year after year, without finding the cause.Energy mode has the microprocessor monitor chamber intensity during exposure and integrate over time, stopping at the set dose: dimmer lamps run longer, higher intensity stops earlier.The UCL-3500 provides both modes.Use energy mode for nucleic acid membrane crosslinking, PCR contamination control and UV mutagenesis, and write the dose into the experimental record; use time mode only when you must align to a fixed exposure time from older literature, or when a sterilization protocol is explicitly judged by time.There is also a practical benefit: changing to new lamps does not force you to re-establish conditions.

How do I choose among the UCL-3500, 3500M and 3500L wavelength versions?

The UCL-3500 (254 nm), UCL-3500M (302 nm) and UCL-3500L (365 nm) are three versions of the same instrument, and the choice depends on what you need to excite.254 nm is UV-C, close to the absorption peak of nucleic acids, with strong biological effect: nucleic acid membrane crosslinking, EMSA membrane crosslinking, PCR contamination control and UV sterilization, UV-induced mutagenesis, RecA mutant screening, pyrimidine dimer induction - this is the version most molecular biology labs need, and the UCL-3500 featured on this page.302 nm is UV-B, gentler than 254 nm with less damage to nucleic acids, often used where you need to observe under UV or activate at a longer wavelength without excessive photodamage.365 nm is UV-A, lower energy and practically non-damaging to DNA directly, mainly for photosensitizer activation (such as psoralen crosslinking), photoaffinity labeling and photocrosslinking of some proteins and biomolecules.The choice comes down to one question: what are you crosslinking, and at what wavelength do you excite it.If you are unsure, send us the protocol - membrane type, nucleic acid type (DNA/RNA), and whether the next step is hybridization, amplification or photoactivation - and we will advise on that basis rather than recommending the more expensive version.

What dose should I set for Southern blot crosslinking?Can I simply copy 120 mJ/cm²?

A commonly cited set of published parameters: to immobilize DNA on a nylon membrane in Southern blotting, UV irradiation energy is set to 0.12 J/cm² (= 120 mJ/cm²), which on a high-power model usually takes 20-40 seconds - this is also where the first impression of the UCL-3500, "it really is fast", comes from.But 120 mJ/cm² is not the universal answer for every membrane: different brands and models specify different recommended UV conditions; nitrocellulose membranes usually need about 20%-30% more dose than nylon, or baking in addition; RNA degrades more readily than DNA and calls for a more conservative dose; wet versus dry membranes and different transfer buffer systems all shift the suitable dose.The correct approach is three steps: 1.Check the recommended value in the instructions for the membrane roll you have.2.Use it as a starting point for a dose gradient (for example 50 / 100 / 150 / 200 mJ/cm²).3.Take the level that gives strong signal without obvious degradation as your lab's standard value, and record the dose, membrane brand and model, and accumulated lamp hours together.This is exactly what the 9 preset programs are for - locking in validated conditions.

Can I decontaminate a PCR tube by irradiating the whole reaction mix?

This is where UV decontamination is easily misapplied.The principle is sound: 254 nm UV makes DNA form pyrimidine dimers, the polymerase cannot read through them, and the contaminant stops being a valid template; published work reports more than 1000-fold reduction of residual template in a tube.The problem is that UV is equally harmful to the other components of the reaction, at the same time: 1.Taq DNA polymerase is highly UV-sensitive.2.Primers are UV-sensitive and the sensitivity is sequence-dependent (primers with adjacent thymines are damaged more readily).3.dNTPs absorb strongly at 254 nm and shade the DNA, so decontamination efficiency drops sharply and longer exposure is needed.4.Tube plastic absorbs UV, so results differ widely between tube types and placement distances.Hence the correct approach: do not treat UV exposure as a general method for "irradiating the whole reaction mix"; if enzyme and primers are already in the tube, exposure directly lowers sensitivity (reported up to 10-fold).Appropriate targets for UV treatment are bench surfaces, pipettes, tube racks, and reagents and consumables that contain no enzyme or primers.If you do use the classic "irradiate the reaction mix" strategy, add enzyme and primers after exposure and validate sensitivity separately for each PCR system.The more robust direction is aliquoting reagents, using filter tips to control aerosols, and adopting UNG/dUTP systems.

How do I tell under-crosslinking from over-crosslinking?

Both are possible, and the symptoms are easy to confuse.Typical signs of under-crosslinking: signal is generally weak after washing and long incubation, or nucleic acid on the membrane tends to come off; a second crosslinking pass (dry the membrane and expose again under the same conditions) usually improves it markedly.Signs of over-crosslinking: signal falls while background rises, bands look diffuse and smeared, and higher-molecular-weight fragments are affected more - excess UV immobilizes nucleic acid while also damaging the nucleic acid itself and probe binding sites.Two ways to tell them apart: first, check whether you ran an uncrosslinked control and a dose gradient (irradiating different regions of one membrane at different doses is intuitive, and easy in the large chamber of the UCL-3500, where you can lay out several dose points in one run); second, recall where the dose came from - if you copied someone's 120 mJ/cm² without checking the instructions for your membrane, redo it at the membrane manufacturer's recommended value first, which is usually more effective than changing reagents.Do not forget the environmental factors: crosslink immediately after transfer, keep the membrane slightly wet, and keep a single layer.Exposing a membrane after it has dried drops efficiency noticeably, and many people misdiagnose that as "not enough dose".

How many samples fit in a 44×34×15 cm chamber at once?Does a 96-well plate fit?

The internal chamber of the UCL-3500 is 44 cm × 34 cm × 15 cm (L×W×H), about 80% more area than the 32×26×15 cm of the UCL-3200 at the same height.That means you can lay out more sheets than on the UCL-3200: several transferred membranes, one full-size agarose gel, or a whole batch that has to be processed in one go.The exact layout and count depend on sample size and the gaps you need to leave; we suggest single layer, sample side up, no overlap, and keeping the whole group in the center region - overlapped areas receive almost no dose (the lower sample is shaded by the upper one), while placing samples against the wall runs into the edge effect.As for plate-format samples such as a 96-well plate, it fits as long as the outer dimensions are within the chamber and it sits flat in a single layer, but note that the plate plastic absorbs part of the UV, so the actual dose cannot be carried over directly from membrane work - if you plan to UV-treat plate samples, validate the dose first.To settle "how many sheets per batch", send us your sample dimensions and we will give you a workable layout based on your actual consumables.

With energy integration, can I stop worrying about lamp aging?

No.Energy mode solves dose accuracy; it does not solve output decay or changes in uniformity.Low-pressure mercury UV lamps lose output continuously over their service life, and the common replacement criterion in the industry is output down to about 70% of the initial value - at that point the lamp still lights, and because of energy integration the dose you set is still delivered and the result still looks correct, only the time needed keeps growing.That creates two practical problems: runs take longer and throughput falls; and uniformity inside the chamber may change, while the dose integrator reads intensity at the sensor position, and an aging sensor also drifts.So: 1.Record accumulated lamp hours and schedule replacement against the rated life.2.Periodically (for example every 3 months, or per your quality system) measure intensity at several positions with an external UV meter and keep the records.3.When output has clearly dropped, or the time for the same dose is much longer than with new lamps, replace the whole set rather than only the lamp that failed.The UCL-3500 uses six 15 W lamps of the same service life; replace them as a set to preserve uniformity.

Can the energy reading on the instrument serve as dose traceability?What else is needed?

The UCL-3500 has a built-in UV sensor that monitors chamber irradiance in real time and performs the energy integration.To be clear about our position: this kind of traceability is normally evidenced by a factory calibration certificate, not by the instrument acting as a legal measuring standard at all times.Ask for the calibration certificate on delivery, check the calibration date and validity, and arrange recalibration per your quality system over the long term.For genuine "provable dose" you also need an independent external check: measure irradiance inside the chamber with a UV meter, cross-check it against the instrument reading and the set dose, and keep the verification records.If your lab has to pass a CMA/CNAS assessment or a customer audit, building energy integration, periodic external verification and lamp replacement records into a logbook is far more solid than a single claim of traceability - auditors look at records.

How hazardous is 254 nm UV, and what rules apply in use?

254 nm is UV-C, the more biologically active part of the UV spectrum, with documented damage to the cornea (photokeratitis) and skin (erythema), and it produces almost no visible light - you cannot see whether it is on, so you do not instinctively look away as you would from a bright light, which is exactly why it is dangerous.Basic requirements: 1.Start the exposure only after the chamber door is fully closed; do not open the door during exposure.2.Do not look into the chamber to check whether the lamps are on; use the display and the beep.3.Before replacing or cleaning lamps, switch off power and let the lamps cool (the tube wall is hot in operation).4.When fitting lamps, avoid touching the quartz envelope with your fingers; grease causes local devitrification and affects output and uniformity.Two more points that are easily overlooked: first, low-pressure mercury UV lamps generate a small amount of ozone in operation (the 185 nm line splits atmospheric oxygen); if there is an obvious smell when you open the door, ventilate the room before continuing.Second, the lamps contain mercury, so a broken lamp must not go into ordinary waste - hand it to a licensed hazardous-waste contractor, and do not simply discard lamps you have replaced.The UCL-3500 has higher power and delivers more UV per unit time, so the "keep the door closed" discipline matters even more than on lower-power models; if the door seal or the door lock is aging or loose, have it repaired rather than using it as is.

What experiments can a UV crosslinker handle, and how does it differ from the UV lamp in a clean bench?

Applications fall into a few groups: 1.Membrane crosslinking and immobilization of nucleic acids - Southern, Northern, Dot/Slot blot, and membrane crosslinking for EMSA gel-shift work; this is its design home, and where a large chamber shows its value.2.Eliminating PCR contamination and UV sterilization.3.UV-induced mutagenesis (UV breeding).4.RecA mutant screening in E.coli.5.Biomolecule and protein crosslinking.6.DNA nicking in agarose gels and restriction digestion experiments related to pyrimidine dimers.The fundamental difference from a hand-held UV lamp or the lamp inside a clean bench is metering: hand-held lamps and bench lamps have no energy integration and no dose readout, and position and distance are entirely manual, so repeating the same conditions twice can give quite different doses - they can only do qualitative surface sterilization or rough irradiation.The UCL-3500 turns UV exposure into a dose that can be set, recorded and reproduced, and covers a larger sample area in one run.If your current practice is "10 minutes under the clean-bench UV lamp and hope it works" while sample volume is growing, the missing piece is exactly this reproducible, batch-capable dose step.

UCL-3500 or UVP/Analytik Jena CL-3000 - how do I choose?

Both belong to the "established brand plus energy integration" category, so the choice comes down to three practical factors.First, capacity: the CL-3000 chamber is 35×27×16 cm, a size smaller than the 44×34×15 cm of the UCL-3500, and lighter (6.8 kg versus 10 kg) and more compact (41×40×26.5 cm versus 55×36×30 cm overall); if your actual sample volume is modest, the CL-3000 saves bench space.Second, brand and quality system: if your organization already runs UVP/Analytik Jena equipment, or the asset register or quality documents already list that model, staying with the same brand is smoother for purchasing, acceptance and consumable management.Third, structural preferences: the CL-3000 has a door with a viewing window (you can watch the run while UV is blocked) and a safety door lock, uses 6×8 W lamps, and is also available in 302 nm and 365 nm versions (order numbers 849-95-0615-01 to -06).To settle it, tell us the maximum number of membranes and the largest size per run, plus whether your organization has a brand preference, and we will give you a direct answer.

Is the UCL-3500 in stock, and can the three wavelength versions be supplied as needed?

Xinysun Instrument (Shanghai) supplies the LUYOR UV crosslinker range and holds stock of the crosslinker series; the UCL-3500 is available in all three wavelength versions (254/302/365 nm) on request, and the same category also offers the UCL-3200 (routine lab workhorse) and the UVP/Analytik Jena CL-3000 (imported reference model) for comparison.Support we can provide: advice on UCL-3200 versus UCL-3500 based on your sample size and count per run; help fixing the wavelength version and starting dose from your membrane type, nucleic acid type and probe system; the supplied-accessory list and a quotation; help obtaining the official datasheet and factory calibration data; and long-term supply of lamps and consumables.Phone 131-2093-6518, or leave a message in the inquiry form at the bottom of the page - we will send the selection advice and quotation together, usually within 2 hours on business days.

Documentation and services

Documentation available on request

  • LUYOR UCL-3500 official product documentation and specifications (including a comparison of the 254/302/365 nm versions)

  • Full difference table between the UCL-3500 and UCL-3200 (power, chamber size, number of samples per run, suitable sample volume)

  • 254 nm crosslinking dose reference table for common membranes, with dose-gradient pilot protocols

  • Sample layout advice for a large chamber, plus methods for verifying the edge effect

  • Chamber irradiance verification log template and lamp replacement log template

Delivery and after-sales

  • Stock in Shanghai, supplied accessories complete (main unit, UV lamps, manual, certificate of conformity, warranty card)

  • Advisory support on capacity assessment, wavelength selection, starting dose and membrane crosslinking method

  • Long-term supply of consumables and spares such as lamps and quartz shields

  • Free replacement within one year, three-year free warranty

Related reading: UV crosslinker selection overview | UCL-3200 routine workhorse | Verifying chamber irradiance with a UV meter | Life science instruments, full range

Previous:US UVP CL-3000 UV Crosslinker

Back to list

Next:UCL-3200 UV Crosslinker

Send inquiry

Message

  • Product Name:

  • Company:

  • Your Name:

  • Phone:

  • Email:

  • Province / Region:

  • Address:

  • Message:

Copyright 2026 Xinysun Instrument (Shanghai) Co., Ltd. All rights reserved.
ICP:ICP-2026046447

SiteMap

Official WeChat QR code

WeChat QR
Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top