Breadcrumb: Home > Applications > Lab Research
Updated:2026-11-17
Views: A blue light transilluminator is an alternative form of the UV transilluminator: the ultraviolet tubes under the bench are replaced by 470 nm blue LEDs, which excite non-toxic dyes such as SYBR Green to emit green fluorescence. The key difference is photon energy. DNA bases absorb strongly near 260 nm, and 254 nm and 302 nm ultraviolet fall right inside that absorption band, so long exposure forms pyrimidine dimers. At 470 nm there is not enough energy for that reaction. This article compares the two systems on sensitivity, sample protection and cost.
A blue light transilluminator is an alternative form of the UV transilluminator: the ultraviolet tubes under the bench are replaced by 470 nm blue LEDs, paired with a blue excitation filter and an amber viewing filter, which excite non-toxic nucleic acid dyes such as SYBR Green and GelGreen to emit green fluorescence, so that bands and markers can be read in a darkened room.
The key difference is photon energy. DNA bases absorb strongly near 260 nm, and 254 nm and 302 nm ultraviolet fall close to that absorption band, so long exposure forms photoproducts such as pyrimidine dimers. The energy at 470 nm is not enough to drive that reaction, so fragments cut and recovered from the gel keep higher fidelity and can go straight into ligation, transformation or sequencing. That is why blue light gel excision has become more common in cloning work - what is protected is not just the operator, but the recovered DNA itself.
Categories and models are listed in the UV and blue light transilluminator section.
In other words, a blue light transilluminator is not an upgraded UV transilluminator but a system that depends on the dye: with the right dye, blue light is the easier route; with the old dye, the blue bench is money spent for nothing.
For how to choose between the two systems, see the comparison section in how to choose a UV transilluminator.
The LUV-450 offered on this site is configured around those four points: 24 blue 470 nm LEDs plus 20 white LEDs, a 26×21cm transillumination area, stepless intensity adjustment from 10%-99%, blue and white dual mode, and LUV-60 amber viewing glasses as standard. Blue mode is for reading and excising bands stained with SYBR dyes, GelGreen and the SYPRO series; white mode is for locating bands and checking well positions before excision, without switching the room lights on and off.
Three operating points: turn the intensity down to just enough to see the band when excising, to reduce unnecessary exposure; wipe the bench with absolute ethanol after use, because residual dye forms false fluorescent spots; switch off room lighting when photographing and hold the matching filter over the bench so that weak bands are not lost. Specifications and pricing are on the LUV-450 LED blue light transilluminator page.
No. The excitation peak of EB is in the ultraviolet, and it barely fluoresces at 470 nm, so a UV transilluminator is needed.
Check whether the dye is blue-compatible, then whether the intensity is set too low and the ambient light too bright, and finally whether the bench carries residual gel or fingerprints.
Yes. Ordinary lenses do not cut off 470 nm; amber glasses filter out the excitation light and pass the fluorescence signal, while reducing blue light exposure to the eye.
Yes, and that is the main advantage of blue light; even so, keep the exposure short and recover the fragment promptly, so that prolonged intense illumination does not cause non-specific damage.
Dual-mode models exist, but most labs keep a UV bench for the EB workflow and a blue bench for non-toxic dyes, running the two side by side and switching by project.
To configure a bench around your dye system, compare the UV and blue light models in the transilluminator section, or contact Xinyisheng Instruments for a selection check.
This article belongs to the common questions section.
Other sections on the same product line include UV transilluminators (excitation through the gel from below for gels and thin-layer chromatography, so bands are read without turning the plate over) and life science instruments (the entry point for fluorescence imaging, UV crosslinking, UV transmission and cell irradiation).
Models mentioned in this article: LUV-450, XEPU-1126, LUV-260. Ranges, accuracy and accessory lists for each model are given on the product page.
Email: info@xinysun.com
Tel: 131-2093-6518
Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai
Copyright 2026 Xinysun Instrument (Shanghai) Co., Ltd. All rights reserved.
ICP:ICP-2026046447
