Xinysun Instrument (Shanghai) Co., Ltd.

Applications

Breadcrumb: Home > Applications > Fluorescent Leak Testing

Industrial Leak Management Practice: Using LUYOR-365L Fluorescent Leak Detection to Turn 'Fix After Leaking' into 'Early Detection'

Updated:2026-11-02Views:

Leakage in hydraulic and lubrication systems is the silent threat of the industrial plant: it does not announce itself, yet it costs continuously in safety, environmental compliance, downtime and fluid loss. This article describes how a zero-leak maintenance philosophy is put into practice, why 365 nm and a large irradiation area matter, a three-step field procedure and a checklist of the places worth inspecting, and how to write leak inspection into the maintenance schedule. The reference instrument is the LUYOR-365L leak detection flashlight: a 365 nm long-wave UV source with an effective irradiation area of about 200 mm at 38 cm, so a whole run of pipe can be swept in one pass.

Xinysun Instruments (Shanghai) Co., Ltd. · LUYOR, USA Leakage in hydraulic and lubrication systems is what the plant calls the "silent threat": it does not announce itself, yet it costs continuously in safety, environmental compliance, downtime and fluid loss. Drawing on the zero-leak maintenance philosophy used by counterparts abroad, this page explains how the LUYOR-365L large-area fluorescent leak detection flashlight moves leak management from "repair once it drips" to "find it early".

Why leakage stays a persistent problem on site

Sealing materials, hoses and fitting technology have improved considerably, yet leakage remains one of the most frequent faults in fluid power systems. Interviews in the industry keep pointing to two root causes. One is poor execution of installation and maintenance practice - a new system that leaks is usually not a component quality problem but a matter of assembly and service habits. The other is missing training - maintenance staff often lack basic fluid power knowledge and come to accept a drip, a damp hose or a weeping valve block as normal, until a small leak turns into downtime.

The real cost of leakage goes well beyond topping up a can of oil:

  • Downtime and output: a leak tends to become a failure in the middle of a production run, and the cost of an emergency stop far exceeds that of scheduled maintenance;

  • Fluid and cleaning cost: oil is lost continuously, leaked oil contaminates equipment and floors, and cleaning hours and wipe consumables keep being spent;

  • Safety risk: an oil film on the floor causes slips, and a high-pressure oil mist carries ignition and injury risk;

  • Environmental compliance: oil that reaches soil or water can trigger penalties, and the cost of disposing of waste water and waste oil rises.

From repairing leaks to zero leak: a change of approach

That leakage is common does not make it normal. More and more companies treat "zero leak" as the maintenance target - not rushing to repair after a leak, but finding and dealing with it while it is still a weep at a point that has not spread. That requires an inspection method meeting three conditions: sensitive enough to see a pinhole seep, fast enough to sweep a whole circuit in one pass, and portable enough to reach height, confined spaces and moving workstations.

Fluorescent leak detection meets all three. A fluorescent tracer is added to the system and circulates with the oil (or with the refrigerant carrier gas); wherever there is a leak, the tracer escapes and collects around the leak point. Under a UV lamp the point glows a bright yellow-green and is located at a glance. The whole process needs no dismantling, does not disturb the seal and does not stop the machine.

Why 365 nm, and why a large area

The fluorescence of a tracer is not strong. If the excitation source itself carries much visible light, stray light drowns the weak fluorescent signal - which is why a white flashlight or a phone UV torch fails to show a weeping point. 365 nm long-wave UV is almost invisible to the eye, the background stays clean, the contrast at the leak point is strong, and it is the usual band for fluorescent leak detection.

What has to be swept on site, however, is rarely a small part but a whole run of pipe, a complete machine or a flange face. A UV torch with a small spot has to be moved inch by inch, which is slow and leaves gaps. The LUYOR-365L is designed for this situation: an effective irradiation area of about 200 mm at a distance of 38 cm and a central intensity of about 6500 µW/cm², so a large area is covered in one pass; it lights immediately with no warm-up; and an 11.2 V lithium battery gives 3-5 hours of continuous work without a power cable, usable on aerial platforms and on mobile equipment.

How to work on site: a three-step method

  1. Add the tracer: add the appropriate grade of LUYOR-6100 fluorescent leak detection fluid for the medium and system volume (6 pack sizes from 30 ml to 18 L, covering a single machine up to plant-level bulk dosing). The dose is far below the system volume and does not change the performance of the medium;

  2. Run the system: operate normally for a period so that the tracer reaches every part with the medium; at a leak it seeps out with the medium;

  3. Irradiate and read: wearing LUV-10 protective glasses, sweep the 365L over pipes, fittings, valve blocks and sealing areas; a yellow-green glow marks the leak point, which is then marked and scheduled for repair.

The tracer stays in the system, so later re-checks need no further dosing - just irradiate. That is what makes it suitable for a preventive maintenance plan: sweep once a week or once a month, and a leak is dealt with while it is still a pinhole.

Checklist of the places worth inspecting

Frequent leak pointCauseInspection advice
Hoses and couplingsAbrasion, flex fatigue, loose fittingsIrradiate the full length; focus on crimped ends and moving sections
Seals and O-ringsAging, hardening, chemical swellingSweep flange faces, end caps and shaft seals circuit by circuit
Tube fittings and threadsInsufficient torque, vibration looseningSlow down over manifold areas and go fitting by fitting
Cylinder rod sealsRod surface scoring, seal wearAfter a full stroke, irradiate the rod surface and the wiper
Manifold blocks and subplate interfacesMachining flatness, gasket failureIrradiate the oil trace pattern on the block to locate the source

The same checklist applies to refrigeration systems, gearboxes, hydraulic power units and the oil circuits of injection molding machines. When checking refrigeration and air conditioning systems, the tracer circulates with the refrigerant, and the compressor, condenser connections, expansion valve and pipe welds are the places to watch.

Writing leak inspection into the maintenance system

The tool is half of the job; leakage control works through procedure and training. Put the fluorescent sweep into the maintenance plan (combining it with the pre-shift check or the weekly service is a practical arrangement), run a short on-site reading course for maintenance staff (use known leak points to set a reading baseline), and photograph and number each leak point for the file, so that a loop of find - repair - re-irradiate to verify is closed. After one round, most shops find more historical leak points than they expected - and because those points are found early, emergency repairs and environmental risk both go down.


Full specifications are on the LUYOR-365L product page, and a comparison of other flashlights in the same band is in the 365 nm blacklight section. LUYOR-6100 leak detection fluids in all sizes and the LUV-10 protective glasses can be supplied with the lamp; Xinysun Instruments holds stock in Shanghai, and a site demonstration or a sample test can be arranged.

Related sections and models

This article belongs to the fluorescent leak detection section.

Other sections on the same product line include 365 nm blacklights (UV area sources for penetrant testing, leak detection and fluorescence inspection, specified by irradiance rather than wattage), fluorescent leak detection (tracer in, UV lamp on the leak, locate before dismantling) and industrial test instruments (the entry point for four lines: UV inspection, tachometry, stroboscopic observation and surface inspection).

Models mentioned in this article: LUYOR-365L, LUYOR-6100, LUYOR-3103. Ranges, accuracy and accessory lists for each model are given on the product pages.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top