Xinysun Instrument (Shanghai) Co., Ltd.

Applications

Breadcrumb: Home > Applications > Fluorescent Leak Testing

How to Find Equipment Leaks in a Paper Mill? Application of Fluorescent Leak Detection Dye in Paper Machines

Updated:2026-11-02Views:

Leaks in a paper mill are often just a few drops a minute, hidden under paper dust, stock and oil film; by the time oil shows on the floor or a low-level alarm trips, the problem has been building for weeks. This article maps the machine positions where leaks are common and hard to find, explains why fluorescent leak detection pays off in this setting, why water-based and oil-based tracers must never be mixed, and sets out the full workflow from dosing and circulation through section-by-section scanning to marking and recheck.

A leak in a paper mill is rarely as straightforward as a burst pipe emptying onto the floor. High-pressure hose fittings on the hydraulic power unit, rotary seals on a dryer cylinder, distributors in the lubrication system, welds on cooling water lines - at these points the seepage rate may be just a few drops a minute, hidden under paper dust, stock and oil film, and quite invisible from floor level. By the time oil appears on the floor, oil spots show up in the sheet, or a machine trips on a low-oil alarm, the problem has usually been accumulating for weeks.

That is why fluorescent leak detection is widely used in the paper industry: it turns finding a leak from an experience-based visual round into a deterministic job that can be completed inside a shift maintenance window. Below, taking LUYOR fluorescent leak detection dye used with a UV/blue leak detection lamp as the example, we set out which equipment in a paper mill is worth surveying, how to choose a dye for three kinds of fluid, and the complete process from dosing to recheck.

Where paper mills leak, and why those points are hard to find

From pulping to papermaking, the equipment around one paper machine falls into two lines: the stock preparation line with pulpers, beaters (refiners), conical refiners, chests and stock pumps; and the papermaking line with the headbox, wire section, press section, dryer section, calender and reel. What really needs watching for leaks are the "invisible" pipes and components that supply oil and water to that equipment.

Equipment and locationTypical mediumLeak symptoms and risk
Reducers and bearing housings on pulpers and stock pumpsGear oil, greaseOil seal seepage enters the chest, causing oil spots in the sheet and stock contamination
Hydraulic loading systems on beaters and conical refinersHydraulic oilPressure will not hold and the disc gap fluctuates, directly affecting freeness stability
Rotary joints and steam condensate lines in the dryer sectionHeat transfer oil, cooling waterThe leak point is wrapped in insulation, so finding it means stripping the insulation
Press section hydraulic power unit and high-pressure hosesHydraulic oilA high-pressure fitting weeps, oil mist spreads across the roll face and leaves regular oil spots
Oil-lubricated parts of vacuum and compressed air systemsLubricating oilOil travels with the air into the system and contaminates forming fabrics and suction rolls

What these locations have in common: they sit high, the space is tight, they are covered by insulation or guards, and the shutdown window is short. The traditional approach is to open everything up after a shutdown, or to work backwards from oil stains on the floor - the former costs labor hours, the latter finds just the leak that has already reached the floor.

Why fluorescent leak detection pays off in a paper mill

The principle is not complicated: a fluorescent tracer fully compatible with the oil in the system is dosed in proportion and circulates with the oil to every fitting and every seal. Where there is a leak, oil carrying the tracer seeps out and emits bright fluorescence under UV or blue light. A micro-seep the eye cannot see becomes a clear bright spot under the lamp.

  • No disassembly: the machine keeps running, keeps its pressure and temperature, so the leak conditions match real operation and a seep does not vanish because the system was shut down and depressurized.
  • Pinpoint location: the glowing spot marks the seepage point directly, with no need to work upstream from an oil stain, which removes a large amount of wasted labor stripping insulation and guards.
  • Repeatable: the tracer stays in the system, so a recheck after the repair verifies whether the fix was complete and closes the loop.
  • Wide coverage: one dose puts every fitting and seal on the whole oil circuit into a detectable state at the same time.

For a paper mill the value is not just saved labor hours. Oil entering the stock system directly produces rejected paper in batches, and oil entering the cooling water system raises discharge compliance issues; finding a seep one or two maintenance cycles earlier is often worth more than the repair itself.

Three media, three dyes: water-based and oil-based do not mix

The usual reason a fluorescent survey fails on the spot is not a weak lamp but a mismatch between tracer and medium. An oil-based tracer added to a water system does not dissolve; it gathers into oil slicks on the surface, traces nothing, and may clog fine filters. A water-based tracer added to hydraulic oil likewise will not disperse evenly. Confirm what the system actually circulates before choosing a dye.

System mediumSuitable modelFluorescence colorReference dosage
Hydraulic oil, gear oil, heat transfer oil, compressor oil and other mineral-based fluidsLUYOR-6100 oil-soluble fluorescent tracerYellow-white (under UV/blue light)About 0.5-2.5 mL/L of system oil volume
Cooling water, circulating water, hydrostatic test waterLUYOR-6200 water-based fluorescent tracer (green)Bright greenDilute 1000:1 to 500:1 in water
Cooling water, closed circulating water circuits (where they must be told apart from other systems)LUYOR-6300 water-based fluorescent tracer (blue)BlueDosed by water volume; 500 mL treats about 3000 L of water

Color coding is particularly useful in a paper mill: one machine often carries hydraulic oil, lubricating oil and cooling water as three separate systems, and different tracer colors tell you at a glance which one a seep comes from. The cost of using the wrong tracer is not just a missed leak - an incompatible agent that enters a system may require a complete oil change to recover.

From dosing to recheck: one full survey in a paper mill

Step 1: establish system oil volume and the dosing point

Begin by establishing the actual oil volume of the system to be surveyed (tank capacity plus the volume held in piping, heat exchangers and accumulators, usually estimated at 1.2-1.5 times tank capacity), then calculate the dose in proportion. Prefer a dosing point on the return line or at the tank return port, so the tracer is sheared and mixed by flow on the way back rather than poured straight into the bottom of the tank.

Step 2: circulate so the tracer reaches the whole system

After dosing, run the machine under its current duty. Circulation time depends on system size and flow rate: a small hydraulic power unit usually distributes the dye evenly in ten-odd minutes, while the lubrication system of a large paper machine may need tens of minutes to an hour. This step cannot be skipped - tracer that has not mixed locally leads to the false conclusion that a region does not leak.

Step 3: scan section by section with a UV/blue lamp

With shop lighting as dim as practical, scan along the pipe runs section by section with the leak detection lamp, concentrating on fittings, flanges, seal faces, rotary joints and hose crimps. A seep glows brightly under the lamp, and even a micro-seep shows as a small halo. For high-level piping, use a long pole or an elevated work platform; for insulated sections, start with insulation seams and drain holes, which are often where a seep emerges.

Step 4: mark, repair, recheck

Mark each leak point immediately with a marker or a tag, and classify it as immediate or scheduled repair by severity. No re-dosing is needed after the repair - the tracer left in the system is still there, so run for a while and check the same position again; no fluorescence means the repair is sound. This closed loop is the most concrete advantage of fluorescent detection over traditional methods.

Operating details that are easy to overlook

  • Confirm seal compatibility before dosing: oil-soluble tracers tend to swell some elastomers, so seals are usually specified in fluorocarbon, PTFE or perfluoroelastomer; for ordinary nitrile rubber, run a small immersion test before long-term contact.
  • Do not treat the tracer as a stop-leak: it is a tracer, it does not change oil viscosity and takes no part in sealing. A leak still needs the seal or fitting replaced by the normal procedure.
  • Fresh oil dilutes the signal: after a large top-up the fluorescence is weaker, so add a small amount of tracer in proportion where needed.
  • The darker the ambient light, the more accurate the reading: by day, work in backlit areas under the machine or inside enclosures, or use a light shield; blue light with yellow filter glasses improves contrast further.
  • Records matter more than the find: log the position, date and treatment of every leak detected in the machine file, and after a few maintenance cycles you can see which type of fitting, or which hose brand, is the frequent failure point.

Frequently asked questions

Will the fluorescent tracer affect the performance of paper machine lubricating oil?

At the recommended ratio the tracer makes up a very small share of the oil and does not change the viscosity grade or the main lubrication properties. The preconditions are the right model for the medium and no overdosing. If the system has strict cleanliness or certification requirements for its oil, take a sample and confirm compatibility beforehand.

A paper machine has several oil circuits - should they be dosed in different colors?

It is worth distinguishing them. Yellow-white for hydraulic systems, green or blue for cooling water; during a round, the color of the glow tells you which circuit a seep comes from and saves the time of checking each system in turn.

Should the leak detection lamp be UV or blue?

Both excite fluorescence. A UV lamp gives higher contrast in a dark environment and suits precise location; a blue lamp is easier on the eyes and carries more visible content, which suits fast wide-area scanning. In practice the two are often used together: scan with blue, then confirm details with UV.

How soon after dosing can results be seen?

It depends on the leak rate. An obvious leak can be found as soon as circulation is complete; a very small one may need the machine to run for hours or even a day or two, so that the tracer has time to pass through the seal gap. For difficult points, schedule a recheck on different shifts.

Related products and further reading

Conclusion

For a paper mill, the real threshold in fluorescent leak detection is not lamp brightness but three things: the right tracer for the medium, enough circulation time for the agent to reach the whole system, and a logbook entry for every leak found. Do those three and one dose covers the whole oil circuit, turning a search that once depended on stripping machines and luck into a routine job that fits inside a maintenance window. If you need a dosing plan based on system oil volume, medium type and site conditions, send us the equipment list and oil information and we will help calculate the quantity and the model.

Related sections and models

This article belongs to the fluorescent leak detection technology section.

Other sections on the same product line are fluorescent leak detection (add a tracer, find the leak point with a UV lamp, locate before disassembly) and industrial test instruments (the entry point for UV inspection, speed measurement, stroboscopic observation and surface inspection).

Models mentioned in this article: LUYOR-6100, LUYOR-6200, LUYOR-6300. Ranges, accuracy and accessory lists for each model are given on the product pages.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top