Xinysun Instrument (Shanghai) Co., Ltd.

Solutions

Breadcrumb: Home > Solutions > Fluorescent Inspection

10 Questions and Answers About Inspection Lamps: 365nm, Irradiance, White Light, Filters, and Protection

Updated:2026-11-17Views:

Ten questions account for a large share of inquiries about inspection lamps: wavelength, intensity, white light, beam size, form factor, light source, power, uniformity, filtration and protection. This article answers each one and ties every answer to a selection criterion you can act on: why 365nm is the working wavelength, what 1000μW/cm² at 38cm actually means, why aerospace specifications also cap the upper limit, whether white light interferes with fluorescence, and how to choose between a focused spot and a flood beam. Where useful, the figures are compared against the LUYOR-3103 series.

Ten questions come up repeatedly in inquiries about inspection lamps (UV-A black lights): wavelength, intensity, white light, beam size, form factor, light source, power, uniformity, filtration and protection. This article answers each one and ties every answer to a criterion you can act on, comparing parameters against the LUYOR-3103 series where relevant - a portable model that ships in volume to magnetic particle stations, and one whose figures happen to illustrate many of the answers.

1. Wavelength and intensity: two hard thresholds

Q1: Why is an inspection lamp built around 365nm? Can 395nm be used for magnetic particle or penetrant testing?

365nm is the "golden wavelength" of the UV-A band, and that status has two sources. One is history: older mercury lamps have a strong mercury line at 365nm, and fluorescent penetrant and fluorescent magnetic particle formulations have been optimized around that wavelength for decades; the yellow-green fluorescence of an indication reaches its contrast when excited at 365nm. The other is standards: ASTM E1417, E1444 and ISO 9934-3 all limit inspection light sources to the UV-A band (320-400nm, peak 360-370nm), and 365nm sits in the middle with margin at both ends.

A 395nm lamp is not impossible to buy, but it is unsuitable for fluorescent inspection, for three reasons:

  • Low excitation efficiency. Common fluorescent penetrants absorb around 365nm; 395nm falls on the falling edge of the absorption peak, so at equal power the excited fluorescence is markedly weaker and fine indications are simply lost.
  • Visible violet interference. A 395nm source carries a large amount of visible violet above 400nm; without a filter the background is lit and the yellow-green indication cannot produce contrast - the whole advantage of fluorescent inspection rests on a "black background".
  • Standards do not support it. Under E3022/ISO 9934-3, a 395nm source does not pass process review for fluorescent magnetic particle or fluorescent penetrant inspection, and it will be written up as a nonconformity at acceptance.

395nm has its own applications: UV curing, authentication, gemstone viewing, and general illumination at non-inspection grade. One sentence to remember: curing goes with 395nm, inspection calls for 365nm.

Q2: What does 1000μW/cm² at 38cm mean? What is the lower limit in the standards? Why do aerospace specifications also cap at 5000μW/cm²?

μW/cm² (microwatts per square centimeter) is a unit of UV irradiance, measuring how much UV-A power a unit area of the workpiece surface receives. 38cm (about 15 inches) is the lamp qualification distance specified in ASTM E3022 - every lamp is reported at this distance, which is what makes an industry table comparable. Note the difference between two positions: the reported value is at 38cm, the process requirement is at the workpiece, and the closer the lamp the higher the intensity at the workpiece.

Lower limit: mainstream standards and aerospace specifications require UV-A intensity at the workpiece of not less than 1000μW/cm², and many critical-part specifications push it above 1500μW/cm². Below that value excitation is insufficient and indications of fine cracks fade in and out.

Upper limit: industries with dense auditing such as aerospace and nuclear power often cap workpiece intensity at 5000μW/cm², for three reasons. High intensity also excites mill scale, oil film and developer residue on the surface, the background brightens and the indication is effectively drowned. Close-range reading produces glare, which accelerates eye fatigue and can raise, not lower, the miss rate. And high intensity usually comes with a narrower spot and worse uniformity (see Q8). So "brighter is better" does not hold for inspection lamps; 1000-5000μW/cm² is the comfortable window in process terms.

As a reference point: the LUYOR-3103/3103D magnetic particle inspection lamp gives 4500μW/cm² at 38cm, which sits in the upper part of that window - used at the customary 30-40cm reading distance, the workpiece surface stays in specification without overexposure. Intensity decays with use, so it is worth adding a UV radiometer for periodic checks.

2. White light and beam: how contrast and coverage are preserved

Q3: Should an inspection lamp have white light or not? What is white light for? Will it interfere with fluorescence?

White light does four jobs at an inspection station: locating and marking indications in fluorescent magnetic particle testing (pen and paper are hard to see under black light), re-checking and photographing records after reading, illumination for non-fluorescent magnetic particle testing, and visual pre-check of the workpiece surface. Swapping lamps one-handed in a darkroom is inefficient, which is why "black light plus white light in one body, with independent switches" has become the usual design for portable inspection lamps.

Will it interfere with fluorescence? Two levels. White light does not destroy the fluorescent material - switch it off and the fluorescence still emits. But while it is on it raises ambient brightness, washes out the contrast of the yellow-green indication, and repeatedly breaks dark adaptation. So the rule is simple: white light off while reading, on while marking and recording. Under ASTM E2297, ambient white light in a fluorescent inspection area should be kept below 20 lux, and white light is the main contributor.

Selection advice: a magnetic particle station almost always has to mark indications, so a model with independent white light saves a work lamp - the 3103 series has a built-in 3W white LED with its own switch, separate from the UV-A. A pure penetrant line, or a reading area with separate white lighting, can use a plain black light without white.

Q4: What is the difference between a focused spot and a flood (diffuse) lens? Which one for aerospace parts?

Focused spot: a condenser lens in front of the LED packs the energy into a small spot a few centimeters across, with very high center intensity, small coverage and a steep edge falloff. It suits inspection at long distance (where a person cannot stand), deep cavities and bore walls, and re-checking or magnifying a local indication.

Flood lens: the beam spreads into a large, even spot (about 200mm diameter on the 3103), with moderate intensity at any point, large coverage and a gentle profile inside the spot. Scanning a weld or a wheel with a flood lamp needs fewer repositions and the edge areas are less likely to be missed.

How to choose for aerospace parts: flood as the main tool. The reason is expanded in Q8 - aerospace specifications place requirements on both intensity and uniformity over the scanned area, and the "bright center, dark edge" distribution of a focused lamp is at a natural disadvantage; in practice a flood lamp scans the whole surface and a focused lamp or a longer working distance handles local difficulties. The 3103 series uses a flood path, and its factory report includes spot distribution data.

Q5: What are handheld, bench and overhead fixed inspection lamps each suited to?

Three forms map to three kinds of working situation, decided by whether the workpiece moves and whether the operator's hands are free:

FormSuitable situationRepresentative models
HandheldMagnetic particle stations working "lamp in one hand, probe in the other"; field welds and mobile inspection at repair sitesLUYOR-3103/3103D, 3105/3105D, LUYOR BB series
BenchBatch inspection of small parts: fasteners, bearings, small castings and forgings passed under the lamp on an inspection tableBench UV lamps, used with a darkroom or light shield
Overhead / fixedProduction lines and large parts: wheels, hubs and panels that need both hands for reading, with the lamp fixed overhead for continuous illuminationLUYOR-3115 overhead (15 LEDs, 9500μW/cm²@38cm, 250×500mm)

When unsure, count hands at the station: if the inspector's hands are both occupied by the magnetizing equipment or the workpiece, go fixed; if one hand is free to hold a lamp, a handheld gives more flexibility.

3. Light source and power

Q6: LED inspection lamps versus older mercury lamps (ZB-100F and similar): what are the pros and cons?

Two advantages remain for mercury lamps: low unit price, and the path dependency of process documents that say "this is how it has always been verified". The drawbacks are structural: several minutes of warm-up before the output is stable, and a cooldown before restarting after a shutdown; the bulb is a consumable with ongoing spare-part and replacement cost; high power draw and heat, with a hot lamp head; mercury content, so transport, storage and disposal fall under hazardous materials rules; and a glass envelope that does not tolerate knocks, which are routine in a workshop.

LED addresses each of these: instant start with no warm-up, narrow-band 365±5nm output that meets the standard with a filter, source life measured in tens of thousands of hours, a fraction of the power draw of a mercury lamp at the same intensity, an aluminum housing that resists impact, and no mercury and no disposal burden. The cost is a higher purchase price, and vigilance about poor-quality emitters - LED wavelength and intensity vary unit to unit, so ask for a type test report and a unit test report when purchasing (the full checklist is in the site article on choosing between LED and mercury).

The direction is clear: ASTM E3022 was written for UV-A LED inspection lamps, and new lines and audit-driven retrofits are almost all moving from mercury to LED. The 3103 series is an LED model reported to E3022, and for users coming from mercury the process parameters (intensity, distance, wavelength) carry over.

Q7: Battery or mains: how to choose? How long does a lithium battery last? Can it run while charging?

By station: for a fixed inspection room with long shifts of continuous work, choose mains (the P version of the 3103, 24V adapter), with no runtime anxiety and stable intensity throughout; for field work, work at height and inspection rounds across several stations, choose battery (the D version, 24V lithium pack), so moving between positions is not tied to a cable.

Runtime: it depends on pack capacity and ambient temperature, and lithium discharge capability drops in the cold, so winter field work has to be discounted. Careful manufacturers do not promise a fixed number of hours; they suggest allocating a spare pack per shift - one in use, one charging, and rotation covers the whole shift.

Charging while running: it depends on the power design of the specific model; some support it, others keep the charging circuit separate from the lamp circuit and do not allow it. Put this item on the confirmation list before purchasing. The robust approach is not to rely on it: allocate a spare per shift, swap as needed, and intensity consistency is actually better.

Q8: What are the consequences of poor spot uniformity?

The consequence is "the lamp meets its rating, the workpiece does not". Poor uniformity means high center intensity with a sudden fall at the edge: aim the lamp at zone A and measure 2000μW/cm², which passes; scan to zone B where the lamp edge just reaches, and the actual irradiance may already be below the 1000μW/cm² floor - fine indications disappear quietly in those edge zones that "look illuminated too". The eye cannot reliably tell 800 from 1500, which makes this one of the more hidden sources of missed indications.

Poor uniformity brings two further problems: the overexposed center excites background fluorescence from surface residue (the upper-limit problem in Q2), and reading distance has to be adjusted constantly, which disrupts the scan rhythm and puts coverage at risk.

Three countermeasures: choose a lamp with an even flood path (E3022 has a specific requirement for spot uniformity, and the 3103 flood spot is gentle within its effective coverage); scan in a fixed rhythm with "spot edges just touching", without skipping; and measure periodically at the spot center and edge with a UV radiometer, so decay or a worsening distribution is caught early.

4. Filtration and protection

Q9: What does the filter do? What is the difference between black filter glass and quartz filters?

The filter in an inspection lamp does one job: block visible light and UV-B/UV-C, pass UV-A near 365nm and block the rest, and preserve the "black background". A UV lamp without a filter system, even with adequate intensity and the correct wavelength, will destroy the contrast of a fluorescent indication through visible light leakage - which is the fundamental reason an inspection lamp and a UV flashlight are two different products.

The two filter types differ in how they work:

  • Black filter glass (Wood's glass): absorbs visible light in the glass material itself; low cost, but limited transmittance, absorption that generates heat, transmission characteristics that may drift slowly under prolonged high temperature, and a certain baseline visible leakage.
  • Coated quartz filter: achieves a steep cut-off curve through coating, with lower visible leakage, higher transmittance and no cracking at high temperature; used on high-intensity and high-power models, at higher cost.

What this means in practice: check whether the "visible light leakage" item in the factory report meets the limit of the standard you work to; if it does, the filter system is acceptable and the terminology does not matter. The 3103 series ships with black filter glass and a report issued to ASTM E3022 and GB/T 5097-2020, so the filter link needs no separate procurement.

Q10: How do I read an IP rating? Can an inspection lamp be used long-term in oily, damp workshops?

Of the two digits after IP, the one before covers solid objects (0-6, 6 being dust-tight) and the one after water (0-8, 8 being continuous immersion). Against the usual needs of an inspection workshop: general dust calls for IP5X at minimum; occasional splashes or cutting fluid calls for IPX4 and above; washdown or outdoor storage calls for IP65/IP67; and for possible immersion (fluorescent penetrant wash stations) look for IP68.

For long-term use in oily, damp workshops, check three things beyond the IP rating: housing material (aluminum dissipates heat well and resists oil, while ordinary plastic tends to age and go sticky with cutting fluid); whether the lamp head has a rubber boot (impact and roll resistance, and easier to wipe clean); and the protection of the switch and cable (water ingress at the switch is a frequent failure point). Taking the 3103 series as an example: aluminum body, rubber boot at the front, easy to wipe down. For wet stations that need an immersion rating, look at the LUYOR-BBMA (8× 365nm LED, 9000μW/cm²@38cm, 28.5cm effective spot, IP68 water-, oil- and penetrant-resistant, usable in wash and immersion environments).

Ten answers at a glance

The ten answers compressed into one quick-reference page; on site, turn to this section:

Why 365nm? Does 395nm work?

The excitation peak of fluorescent penetrants and magnetic particle suspensions is at 365nm, and standards limit inspection sources to the UV-A band; 395nm has low excitation efficiency and its visible violet output ruins contrast, so it suits curing and other non-inspection uses.

What does 1000μW/cm² at 38cm mean? What is the intensity window?

38cm is the qualification distance in ASTM E3022; workpiece intensity must be at least 1000μW/cm², with an aerospace upper limit of 5000μW/cm² - too high and surface residue fluoresces as background while glare increases.

What is white light for? Does it interfere with fluorescence?

White light is used for marking indications, re-checking records and non-fluorescent inspection; it does not destroy fluorescence but washes out contrast, so it has to be off while reading, and a model with independent black and white switches is preferable.

Focused spot or flood lens?

Focused suits deep cavities, bores and long-distance re-checks; large-area scanning and aerospace parts favor flood, with even coverage, fewer repositions and fewer missed edges.

Handheld, bench or overhead fixed?

Handheld matches magnetic particle stations and field inspection, bench matches small-part batches passed under the lamp, and overhead fixed matches two-handed reading of large parts on a line.

LED or older mercury?

LED starts instantly, lasts long, contains no mercury and tolerates impact, and is reported to ASTM E3022; mercury retains an advantage in unit price and path dependency, and is being replaced.

Battery or mains? How long does it run?

Mains for fixed stations, battery for mobile inspection; runtime depends on pack capacity and temperature, so allocate a spare pack per shift; running while charging depends on the model design.

What happens with poor spot uniformity?

The lamp meets its rating while the edge zone falls below the intensity floor, producing hidden misses; choose an even flood model, scan with spot edges just touching, and measure center and edge periodically.

Black glass versus quartz filter?

Both exist to preserve the black background; black glass is cheaper but heats up and may drift, while a coated quartz filter cuts steeply, leaks less visible light and tolerates heat, and is used on high-intensity models.

How do I read the IP rating? Can it be used in a damp workshop?

The digit before is dust and the one after water: IP65 and above for washdown, IP68 for immersion; also check the aluminum housing, the rubber boot and the protection of the switch and cable.

Putting the ten answers into one lamp

To close: if the ten questions are used to reverse-engineer the standard answer for a magnetic particle station, it should be - 365±5nm, intensity at 38cm inside the 1000-5000μW/cm² window, a wide flood spot, independent black and white switches, factory-fitted filtering with a full report set, and a power option of mains or battery. The LUYOR-3103/3103D portable magnetic particle inspection lamp is designed to that list: 3 high-power UV-A LEDs plus 1× 3W white LED, 4500μW/cm²@38cm, about 200mm flood spot, P and D power options, 3-year warranty. Fixed stations with longer shifts can use the overhead LUYOR-3115, and those wanting higher portable intensity can look at the LUYOR-3105/3105D (7000μW/cm² at 38cm). For selection and report verification at a specific station, bring the process documents; standards compliance and audit questions (E3022 reports, Nadcap certificates, metrology calibration, export certification) are covered in the companion article six questions on inspection lamp compliance.

Related sections and models

This article belongs to the frequently asked questions section.

Other sections on the same product line include 365nm black lights (UV area sources for inspection, leak detection and fluorescence, judged on irradiance rather than wattage), UV radiometers (measuring intensity in mW/cm² and accumulated energy in J/cm², the tool for judging whether a lamp is compliant) and life science instruments (the entry point for fluorescence imaging, UV crosslinking, UV transmission and cell irradiation).

Models mentioned in this article: LUYOR-3103, LUYOR-BBMA, LUYOR-365L. Ranges, accuracy and accessory lists for each model are given on the product pages.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top