Xinysun Instrument (Shanghai) Co., Ltd.

Applications

Breadcrumb: Home > Applications > Lab Research

GFP/RFP Transgenic In Vivo High-Throughput Primary Screening: LUYOR-3415 for In Situ Observation Without Moving Samples

Updated:2026-11-02Views:

Transgenic and gene-editing labs often stall at the same step: how to pick reporter-positive individuals quickly. Once sample numbers climb, carrying hundreds of tissue-culture jars and thousands of seeds into a darkroom one by one is slow and often damages the material. This article describes an in-place prescreen workflow built around LUYOR-3415: GFP, mCherry and DsRed fluorescence is read beside the culture rack without moving any sample. It also sets out the limits of the method, the operating steps and the points that decide whether a call is reliable, and it positions the tool as an upstream screen rather than a microscope replacement.

Labs working on transgenics and gene editing almost all stall at the same step: how to pick out reporter-positive individuals quickly. Markers such as GFP, mCherry and DsRed are invisible under ordinary light; they have to be excited at the right wavelength and viewed through matching filter glasses before they can be told apart. And once sample numbers climb - hundreds of culture jars, thousands of seeds, a whole greenhouse of potted seedlings - "carry them into the lab one at a time and look" becomes one of the slowest steps in the whole workflow, and often the step that damages valuable material first.

The LUYOR-3415 portable dual-wavelength excitation source was built for exactly this kind of live, high-throughput prescreen: carry it by hand to where the material is, illuminate in place and judge in place. The rest of this article sets out where this route applies, how to run it, and what decides a reliable call.

Why batch fluorescence screening gets stuck on moving samples

Putting each route in its place in the workflow makes the difference clear:

RouteIn-place observationDamage to the sampleThroughputMain bottleneck
Fluorescence microscope / stereo fluorescence microscopeNo; requires sampling or moving material into the labSampling is destructive, so the material cannot be grown onLow; one field of view at a timeNarrow field, scarce instrument time, time lost to transport
GUS histochemical stainingNo; it is an excised-tissue assayDestructive; stained material cannot be reusedMedium, but each run takes a long timeOvernight processing, reagent consumption, no live re-screening
Large in vivo imaging systemImaging happens inside the instrument, but the material must be loaded into itUsually non-destructiveLimited by instrument time and chamber sizeHigh purchase cost, booking schedules, poorly suited to large prescreens
Portable excitation sourceYes; the material stays where it isNon-destructive; the same plant can be observed repeatedlyHigh; screen one batch after anotherGives a yes/no fluorescence call only, no quantitative imaging

The first three routes are each mature, but all of them require the material to leave its place: the microscope needs a sample or a move, GUS destroys the sample and cannot reuse it, and the imaging system is non-destructive yet carries instrument time and cost that make little sense for a large prescreen.

Transgenic screening has a further reality: most candidate material is in fact negative, and only the small fraction that survives screening needs detailed characterization. Sending negative material to the microscope or the imager spends high-end instrument time and labor on exclusion. The prescreen step therefore needs a different tool - fast, in place, non-destructive, and able to work through large batches back to back.

What LUYOR-3415 is designed to solve

The design goal is straightforward: put two excitation wavelengths into one handheld device that can be carried to the culture bench, the growth chamber, the greenhouse and the field.

  • Two excitation bands, covering the two main groups of fluorescent proteins with one unit: the standard configuration pairs RB royal blue (440-460 nm, with a 500 nm filter) for GFP, eGFP and fluorescein with GR green (510-540 nm, with a 600 nm filter) for DsRed, tdTomato and mCherry. Independent switches on the lamp body change bands, so material carrying two markers needs neither a second device nor a fresh alignment.

  • High output, so material is readable through the jar wall and the medium: 12 LEDs across the two bands, 27 W total. Viewing through a culture jar wall and the medium asks more of the excitation power than direct illumination does, and the power margin is what decides whether "one layer away" is still readable.

  • Lithium battery and handheld format, with no site restriction: about 0.9 kg, supplied with a rechargeable battery pack and a carry case, so it travels to the greenhouse, the field or the culture room. Under strong ambient light, a shading cloth is used to darken the background first.

  • Simple operation, read by eye: wear the matching viewing glasses to filter out the excitation light, and visible fluorescence is the positive signal. No image processing and no specialist training are needed.

  • A large illuminated area, suited to screening a batch at a time: at a working distance of about 150 mm the beam is about 180 mm across, enough to cover a cluster of seeds, a whole Petri dish or a whole seedling in one pass.

  • Wavelength pairs configurable to the project: any two of the R, C, G, V and U sources can be assembled, so projects using CFP, BFP or DAPI nuclear staining can be matched as well.

Core application scenarios

Scenario 1: screening plant transgenic material

The coverage here is broad - Arabidopsis seedlings, crop hairy roots, culture callus and potted seedlings can all be examined for GFP/RFP fluorescence where they stand, with no root cutting and no sampling.

Non-destructive screening inside culture jars and vessels. Material in a sealed vessel normally has to be opened or taken out before it can go under a microscope, and the contamination risk from opening a jar can sometimes waste the entire batch. With a portable source the jar stays closed: aim the light at the wall and look through the wall and the medium for fluorescence in the plants inside. Positive material stays in the vessel and keeps growing; negative material is handled as required. Screening and maintenance of the line happen at the same time.

Live in-place observation in the greenhouse and the field. Potted seedlings and field plants need neither transport nor sampling; illuminate by hand and read the result. The same plant can be observed repeatedly, tracking changes in fluorescence expression over time. This matters especially for transformation events with long growth cycles or limited material - every sample taken is one plant fewer, whereas in-place observation uses one plant to the end.

Roots and hairy roots. Root material such as soybean hairy roots has to be taken out and spread flat under a microscope, which is laborious and hard to undo. With an excitation source and the culture vessel in place, root segments with clear fluorescence can be picked out first, and only those worth closer examination are taken forward.

Large-format plate and seed sorting. Fix the source on an adjustable stand at a suitable working distance, and both hands are free to look and sort at the same time, turning "one seed at a time" into "one batch at a time". Where a batch carries two fluorescent markers, switching bands allows a direct comparison without changing light sources.

Scenario 2: in vivo observation of model animals

Fluorescent markers are not limited to plants. Zebrafish embryos and fry, and juvenile transgenic mice, can be prescreened on the same device, removing individuals that do not express fluorescence before they consume rearing and observation effort. The procedure matches plant screening: illuminate, put on the glasses, read, and switch bands when GFP and RFP markers need to be compared.

In practice: running a single in-place prescreen

Getting comfortable with the device does not take a complex procedure, but a few steps decide the accuracy of the call:

  1. Reduce the ambient light first. Fluorescence is a weak signal, and the brighter the surroundings the harder it is to resolve. In a culture room, turn off part of the lighting; in a greenhouse or the field, screen the observation area with a shading cloth. Both the visual impression and any photograph become noticeably cleaner.

  2. Choose the right band and test it first. Use the RB royal blue band for GFP/eGFP and the GR green band for DsRed/mCherry. Illuminate a known positive sample once to confirm that the glasses match the band, then start batch screening.

  3. Keep to a suitable working distance. Too close and the covered area is small and slow; too far and the signal falls off. About 150 mm corresponds to an illuminated diameter of about 180 mm, which suits most vessels and seedlings. For material inside a jar, move in close and use the power margin to offset the loss through the wall.

  4. Wear the matching viewing glasses before judging. The glasses filter out the excitation light and pass only the fluorescence. Without them the eye sees reflected excitation light, which is easily misread.

  5. Record, then confirm. Mark positive material and note its position for later tracking. For samples with weak signals or unusual positions, change the angle or the ambient light and look again before deciding.

One observation point that is easily missed: red fluorescent proteins are often constrained by filter cube configuration under a microscope, whereas under a high-power dedicated handheld source the visual result is often good. If a project relies mainly on red fluorescent markers, this type of source is worth considering first.

Positioning: an upstream screening tool, not a replacement for the fluorescence microscope

This needs to be stated clearly in use and in reporting, so that the tool is not mispositioned:

StepObjectiveSuitable tool
Batch prescreenDecide quickly whether fluorescence is present, and narrow the fieldPortable excitation source: in place, non-destructive, high throughput
Detailed imagingCellular and subcellular localization, intensity quantification, image recordsFluorescence microscope, stereo fluorescence microscope
ConclusionConfirm the transformation event and expression levelMolecular assays (PCR, western blot and similar)

The division of labor is this: pick the positive individuals with the excitation source first, then let the microscope and molecular methods handle the material worth analyzing in depth. High-end instruments then work on the samples that genuinely need resolution and quantification, and instrument time is used more efficiently. The prescreen itself is not a conclusion, only an efficient way to narrow the field.

Practical benefits

  • Saves a large share of GUS staining reagent and processing time. Live observation replaces part of the excised-tissue staining, cutting reagent consumption and removing the overnight processing and the wait for a result.

  • Relieves the booking queue for the fluorescence microscope. Taking large-batch triage off the microscope leaves it for detailed imaging, and the pressure on instrument time eases noticeably.

  • Avoids damage to valuable material from sampling. In-place observation cuts no roots, takes no leaves and moves no plants; when transformation events are few, every plant saved is one more usable line.

  • Raises the throughput of material generation. Moving from "one plant at a time under the instrument" to "one batch at a time" lets the same staff work through more candidates.

  • Supports continuous tracking. The same plant can be observed repeatedly at different growth stages, recording how fluorescence expression changes over time.

Which labs can use it

  • Crop genetics and breeding: batch screening and seed sorting of rice, soybean, maize and other transformants

  • Plant developmental biology: live fluorescence observation and tracking in Arabidopsis and other model plants

  • Horticultural transgenics: non-destructive screening of culture plantlets and potted material

  • Microbiology and root transformation: hairy roots and fluorescently marked colony screening

  • Model organism facilities: prescreening fluorescence expression in zebrafish, transgenic mice and similar

Frequently asked questions

Is a call made without sampling reliable?

For prescreening, yes. Positive material shows clear fluorescence under the correct band with the matching glasses, and negative material does not. Note that the result is a qualitative present/absent call; it provides neither intensity quantification nor subcellular localization, which still require a microscope.

Does the jar wall block the fluorescence signal?

The wall and the medium do attenuate the signal, which is why this scenario asks more of the excitation power. In practice, move close to the wall, turn off ambient light and change the angle if needed. The 12-LED, 27 W configuration exists so that viewing through a vessel stays readable.

Why are the glasses needed to see fluorescence?

Because without them the eye receives both the fluorescence and the far stronger reflected excitation light, and the weak signal is swamped. The matching glasses filter out the excitation band and pass only the fluorescence, so the signal appears.

What if one batch carries both GFP and RFP markers?

Use the dual-wavelength configuration. The two switches on the lamp body correspond to the two bands, so changing over needs no second device and no realignment, which suits rapid comparison of two markers on the same batch.

Can fluorescence prescreening replace molecular identification?

No. Its role is to narrow the field quickly and pick candidate positives; the conclusion still rests on molecular methods. Using it as the step before molecular identification is the reasonable positioning.

Is the field or greenhouse too bright to read?

It can still be read, provided the ambient light is reduced. In the open, screen the observation area with a shading cloth, or work on an overcast day, in the early morning or in the evening, when ambient light is weaker; the reading improves noticeably.

Can the device be taken on a train or a flight for sampling trips?

At about 0.9 kg with a rechargeable battery pack and a carry case, it is easy to transport. Air transport of lithium batteries is subject to specific rules, so confirm the carriage requirements with the carrier before travelling.

Can red fluorescent proteins be screened?

Yes. The GR green band (510-540 nm, with a 600 nm filter) corresponds to red fluorescent proteins such as DsRed, tdTomato and mCherry, and in practice the visual result is usually easier to resolve than under a microscope.

Related products and further reading

Conclusion

The real bottleneck in batch fluorescence prescreening is rarely whether fluorescence can be seen, but whether material has to be moved and sampled. Bring the excitation source to the culture bench, the greenhouse and the field, and let the material be observed where it stands: the prescreen turns from one of the slower parts of the workflow into a smooth step. The positives it picks then go to the microscope and to molecular methods, so that high-end instruments work on the high-value part of the job.

The LUYOR-3415 series is currently available for short-term trial, and literature cases and live fluorescence photographs can be provided for reference. If you need to confirm a wavelength combination and matching filters for your markers (GFP, RFP, CFP, DAPI and others), please contact us.

Related sections and models

This article belongs to the Research laboratory techniques section.

Other sections on the same product line include GFP fluorescence flashlights (models sorted by GFP/RFP/DsRed band, in handheld and benchtop formats) and Life science instruments (the entry point for fluorescence imaging, UV crosslinking, UV transmission and cell irradiation).

Models mentioned in this article: LUYOR-3415, LUYOR-3124RB and LUYOR-3421. Ranges, accuracy and the accessory list for each model are given on its product page.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top