Breadcrumb: Home > Applications > Lab Research
Updated:2026-11-02
Views: Treating UV as a controlled independent variable demands three things: a dose that can be stated, a sample that fits, and a temperature that can be held. This article begins with the conversion between dose and time, then compares how the UVA, UVB and UVC bands act, sets out the two preconditions most often skipped - sample size and temperature - and describes six experimental designs. It closes with questions on how the LUYOR-3550 and the LUYOR-3450 divide the work. The reference instrument is the LUYOR-3550 UV irradiation chamber: a 68×55×32 cm cavity, a 67×52 cm sliding sample platform and 20 × 15 W UV lamps.
In microbiology and cell labs, one common use of UV is "open the lid and irradiate for 30 minutes". Used as a controlled independent variable, however, the experiment looks quite different: mapping a lethality curve to calibrate a mutagenesis dose, establishing the kinetics of DNA damage repair in cells, or reviving UV-killed bacteria with blue light to demonstrate photoreactivation. All of these share three requirements: a dose that can be stated, a sample that fits, and a temperature that can be held.
The LUYOR-3550 UV irradiation chamber is a mid-size unit from LUYOR: a 68×55×32 cm irradiation cavity, a 67×52 cm sliding sample platform and 20 × 15 W UV lamps. This article follows the order in which an experiment actually develops - which band to choose, how to calculate the dose, and how to design the protocol.
The cost of skipping this step is usually discovered months later, when the data will not reproduce. The conversion is simple: irradiation time (s) = dose (J/cm²) × 1000 ÷ irradiance (mW/cm²). Filling in the band configurations of this instrument:
| Band | Peak wavelength | Irradiance | Dose delivered per hour |
|---|---|---|---|
| UVA | 365 nm | 7 mW/cm² | about 25 J/cm² |
| UVB | medium wave | 2.4 mW/cm² | about 8.6 J/cm² |
| UVC | 254 nm | 8 mW/cm² | about 28.8 J/cm² |
A few commonly used values: for UVA, 1 J/cm² takes about 2.4 minutes and 15 J/cm² about 36 minutes; for UVC, 40 mJ/cm² takes just 5 seconds and 1 J/cm² about 2 minutes.
The UVC numbers deserve a separate look. Plenty of labs still run UV disinfection on "5 minutes of irradiation"; at 8 mW/cm² that gesture corresponds to a dose that can wander between a few hundred and a thousand-odd mJ/cm², so the error in manual timing is larger than the dose itself. For data you intend to publish, quantify in energy mode rather than counting seconds.
UVA (365 nm, 7 mW/cm²) penetrates deeper and acts mainly through reactive oxygen species and photosensitisation, producing indirect damage, so its effect is relatively mild. For skin photoaging models, sunscreen efficacy testing and photosensitiser activation, UVA is the preferred band. Cosmetic research groups use this instrument to model cumulative UVA exposure in human fibroblasts, with a target dose of 15 J/cm².
UVB (medium wave, 2.4 mW/cm²) acts mainly in the epidermis, where direct photoproducts plus oxidative stress give a clear biological effect. It is the band for sunburn-like injury, epidermal damage models and dose-response studies.
UVC (254 nm, 8 mW/cm²) carries high energy and penetrates shallowly, forming pyrimidine dimers directly in nucleic acids. Disinfection, UV mutagenesis, surface modification and UV grafting all rely on it; inactivation is efficient, and the risk to eyes and skin is correspondingly higher.
450 nm blue light is an optional configuration covering the visible band, used mainly for photoreactivation, optogenetics, blue-light-responsive proteins and as an approximate source for visible-light catalysis.
The instrument accepts two UV band control panels, each governing one spectral range with its own setting and constant-dose hold. A cumulative-damage design of "UVA first, then UVB", or two bands for two batches of samples, can be run on one machine.
A small irradiator suits plates and sections. Once the sample becomes a whole animal, a batch of dishes or a slab of material, size and uniformity become hard limits: if it will not fit, or half of it is shadowed once inside, any later discussion of dose is pointless. Counting 90 mm dishes, the 67×52 cm platform holds about 30 at a time. The platform pulls out of the cavity, so labelling and sampling are done outside and the door stays open for much less time.
Temperature matters more. With 20 × 15 W lamps running continuously, a thermal equilibrium forms inside the cavity. Under an open lamp frame the heat is carried away by the room; in a closed chamber without active cooling the temperature climbs into a range that affects cell viability. At that point the difference you measure may come from heat rather than from UV, and the experiment is wasted. This instrument has 4 high-power fans and holds the sample area below 37 ℃.
Lethality curve for UV mutation breeding. The logic is that a high dose kills too hard and a low dose leaves the defect unfixed, so the useful window sits in between. Run a gradient from 0 to 300 mJ/cm² first and locate D90 (90% lethality) and D99. At UVC 8 mW/cm² the top group of that gradient takes 40 seconds. Incubate in the dark afterwards, so photoreactivation does not confound the result.
Verifying a UVC disinfection dose. Start a gradient at 40 mJ/cm², a common benchmark for drinking water and surface disinfection, plate immediately after exposure and calculate the log10 reduction. The 254 nm dose-response is monotonic, and this instrument delivers 40 mJ/cm² in 5 seconds, so a full gradient costs little machine time and can be repeated for verification.
DNA damage and repair kinetics in cells. Plate overnight, irradiate at 0, 2, 5, 10, 15, 20 and 30 J/cm², return immediately to fresh medium in the dark, and sample at 0, 15 min, 1 h, 3 h, 6 h and 24 h. Read out two endpoints: γH2AX foci (a break signal) and colony formation (the true survival curve); where the two disagree, take the clonogenic result.
Phototoxicity and chronic UVA modelling. Cumulative doses of 3 to 10 J/cm² are usual; at 7 mW/cm², 5 J/cm² takes about 12 minutes and 10 J/cm² about 24 minutes. One caveat: if the subject is cells in a 96-well plate and a single 365 nm band with a quantified dose is all you need, the LUYOR-3450 cell phototoxicity irradiator from the same series fits better - its cavity is sized for plates (26×32×15 cm), it carries a fixed 3T3 NRU program, and the results feed directly into OECD TG 406 documentation. Use the 3550 when animals, large samples or a combination of bands are involved.
Photoreactivation. This is where the blue-light option earns its place. Photolyase uses visible light (peak around 350 to 450 nm) to repair the pyrimidine dimers formed by UV. The design is simple: irradiate bacteria with UVC or UVA down to 10-50% survival (UVC 254 nm, about 100 to 300 mJ/cm²; UVA 365 nm, about 5 to 10 J/cm²), then split into three groups - A into the dark immediately, B immediately illuminated with 450 nm blue light for 30 to 60 minutes, and C illuminated with visible light that excludes blue. Then count. If survival in B is clearly higher than in A, the dose sits in a repairable window; if A and B do not differ, the dose was too high or the damage is not photorepairable.
This experiment demands more of operating discipline than of hardware: everything after UV exposure must be handled in the dark or under a red safelight, and a single glance under the room lights is enough to contaminate the negative control.
Attributing a mechanism to the photosensitiser and ROS. The difficulty is separating damage caused by light from instability of the molecule itself. The grouping is: no-light control, light alone, light plus photosensitiser, and light plus photosensitiser plus an ROS quencher or scavenger (SOD, catalase). If the effect falls sharply once the quencher is added, the ROS pathway can be credited. These runs favour low dose and short time, so that degradation of the sensitiser itself does not masquerade as falling kinetics; the dimming knob for lowering intensity and the energy mode for stopping at a set dose are therefore core functions here.
The cavity uses a diffuse-reflection light path and irradiates evenly, so samples can be placed in any order. Even so, after first installation, a lamp change or cleaning of the cavity, run one 3×3 nine-point measurement with an independent UV radiometer and record the dose deviation between the centre, the four corners and the edges. For samples wider than 10 cm, do not skip this step.
Keep each group in the same place on the platform, run after run, and note in the record whether lids were open, the spacing between samples and how far the platform was pulled out.
Manage the lamps by life as well. Reference life is about 4000 hours for UVA and UVB and about 9000 hours for UVC. Log cumulative hours per band and re-check the in-cavity dose towards the end of life, rather than judging by hours alone.
The core difference is sample size and the number of bands. The LUYOR-3450 is aimed at quantified UVA irradiation of 96-well plates: a 26×32×15 cm cavity, 365 nm as standard, and a fixed 3T3 NRU program. The LUYOR-3550 has a 68×55×32 cm cavity, takes 20 × 15 W lamps, and offers UVA/UVB/UVC as options or in combination. For cell phototoxicity work take the 3450; when animals, larger samples or two bands at once are involved, take the 3550.
Start from the biological endpoint you need to observe. UVA penetrates deeper and acts mildly, which suits skin photoaging models and photosensitiser activation; UVB is for sunburn and epidermal damage models; UVC at 254 nm carries high energy with shallow penetration and is used mainly for disinfection, UV mutagenesis and surface treatment.
Yes. Two UV band control panels can be installed, each governing one spectral range with its own setting and constant-dose output. That suits applying two bands in sequence or in combination, for example a cumulative-damage study of UVA followed by UVB.
The cavity is 68×55×32 cm with a 67×52 cm sliding sample platform, enough for several multiwell plates, a batch of dishes, whole mouse cages or bulk material samples. Counting 90 mm dishes, about 30 fit at a time; the exact number depends on sample height and how they are arranged.
Yes. The dimming knob sets UV intensity, covering both low-dose chronic modelling and high-dose accelerated tests; with energy mode the run stops automatically at the set dose, so no manual timing is needed.
It means the dose the sample actually receives does not drift with lamp ageing, cavity soiling or temperature change. A calibrated sensor measures the dose - it contains a high-precision analog-to-digital converter and a temperature sensor - and the control panel closes the loop on the measured value.
Four high-power fans keep the sample area below 37 ℃, so thermal effects do not interfere with the result. In cell and bacterial work this is a precondition for excluding a confounding factor, not an optional extra.
UVA and UVB lamps last about 4000 hours and UVC about 9000 hours, enough for long uninterrupted runs. Lamps are replaced as complete tubes; log cumulative hours and re-check the in-cavity dose setting after replacement as needed.
Keep the door closed throughout a run, and never look into the lamps or expose skin to the UV inside the cavity with the door open. UVC at 254 nm carries a higher risk to eyes and skin and may generate ozone during operation, so the instrument should stand in a well-ventilated place. Isolate the power before changing lamps or cleaning the cavity.
LUYOR-3550 UV irradiation chamber: 20 × 15 W lamps, UVA/UVB/UVC options, two-band control panel available;
LUYOR-3450 cell phototoxicity irradiator: quantified UVA irradiation of 96-well plates, fixed 3T3 NRU program;
LUYOR-3480 microplate cell irradiator: a cell irradiation option sized for microplates;
UV irradiation equipment section: the overview of LUYOR UV irradiation and exposure equipment;
Life science instruments section: laboratory and biology-related detection equipment;
Eight application scenarios for the UCL-3200 UV crosslinker: a different class of work under UV curing conditions;
Photostability testing: dose setting, temperature control and control design: a comparable dose design approach for pharmaceutical and cosmetic systems.
Compressed into one line: fix the biological endpoint, convert the dose into time, then check the cavity size and the temperature conditions. The endpoint decides the band, the band decides the configuration, the dose decides the irradiation time, and the sample volume decides the cavity size. Write these four into the opening of the methods section and everything that follows will stand up. For help calculating irradiance and lamp configuration for a specific experiment, or checking whether a single exposure fits your schedule, contact us.
This article belongs to the Laboratory research techniques section.
Other sections on the same product line include UV irradiation chambers and photochemical reactors (quantified exposure of cells, microplates and materials), UV crosslinkers (dose set in J/cm², the figure that matters for both nucleic acid crosslinking and material curing) and Life science instruments (the entry point for fluorescence imaging, UV crosslinking, UV transmission and cell irradiation).
Models mentioned in this article: LUYOR-3550, LUYOR-3450, LUYOR-3480. Ranges, accuracy and the accessory list for each model are given on its product page.
Email: info@xinysun.com
Tel: 131-2093-6518
Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai
Copyright 2026 Xinysun Instrument (Shanghai) Co., Ltd. All rights reserved.
ICP:ICP-2026046447
