Breadcrumb: Home > Applications > Lab Research
Updated:2026-11-02
Views: Moving a medicinal plant's secondary metabolic pathway into a heterologous host often stalls at a very basic step: after transformation, how do you pick the hairy-root clones that actually carry the transgene out of dozens or hundreds of candidates? In its Salvia miltiorrhiza work published in Plant Communications, a Zhejiang Sci-Tech University team read the DsRed label with a LUYOR-3415RG. The paper runs two heterologous routes in the same chassis, taxadiene from TwTS and protopanaxadiol from PnPPDS. This article sets out the screening workflow, the numbers behind it (65.17 ± 5.25 mg/kg FW taxadiene, 50.04 ± 2.94 mg/kg DW protopanaxadiol) and the handling points a lab can copy.
Moving the secondary metabolic pathway of a medicinal plant into a heterologous host has become a common route in plant synthetic biology. Further into the engineering, though, what limits throughput is usually not pathway design but a very basic task: after transformation, how to sort out the lines that really carry the transgene among dozens or hundreds of hairy-root clones, and do it quickly. In the Salvia miltiorrhiza hairy-root work that a Zhejiang Sci-Tech University team published in Plant Communications, this step used the DsRed red fluorescent protein carried on the vector, read with a LUYOR-3415RG dual-wavelength fluorescent protein excitation light source. This article follows that paper's screening workflow and sets out operating points that can be reproduced.
The study used hairy roots of Salvia miltiorrhiza as the chassis and ran two product routes at the same time. One expressed taxadiene synthase TwTS from Taxus wallichiana, producing taxadiene, the key precursor of the anticancer drug paclitaxel; the other expressed protopanaxadiol synthase PnPPDS from Panax notoginseng, producing the ginsenoside precursor protopanaxadiol.
The chassis was induced by infecting S. miltiorrhiza leaves with Agrobacterium rhizogenes ATCC15834, then monocloned so that each line could be assessed on its own;
CRISPR-Cas9 was used to knock out SmCPS1, closing down the tanshinone route that competes for GGPP and steering precursor flux toward the target product;
The transcription factor SmWRKY61 was overexpressed to strengthen upstream precursor supply through MVA/MEP;
Culture optimisation and methyl jasmonate (MeJA) induction were layered on top for yield scale-up.
With all three measures combined, taxadiene reached 65.17 ± 5.25 mg/kg fresh weight (FW) in batch culture, about 21.6-fold higher than lines expressing TwTS alone; protopanaxadiol reached 50.04 ± 2.94 mg/kg dry weight (DW) in lines that had received no further optimisation.
| Item | Result reported | What it means for the workflow |
|---|---|---|
| Chassis | S. miltiorrhiza hairy roots, induced with ATCC15834, monoclonal lines | Sterile and subculturable long term, suited to a scale-up platform |
| Selection marker | The vector carries the DsRed red fluorescent protein gene | A preliminary call by eye after transformation, before extraction assays |
| Taxadiene | 65.17 ± 5.25 mg/kg FW (after MeJA induction) | Combined strategy gives about a 21.6-fold gain over single-gene expression |
| Protopanaxadiol | 50.04 ± 2.94 mg/kg DW (no extra optimisation) | The same chassis can be switched to a different heterologous route |
| Scale-up check | 5 L bioreactor, 3 L medium, 30 days, 8.52 mg/kg FW (7.69 in shake flask) | Shake-flask results transfer to the bioreactor, so scale-up looks feasible |
| Culture conditions | 6,7-V liquid medium, 25 ℃ dark, 110 rpm, 30 days | Matches routine hairy-root culture, no special equipment |
The methods section is direct about this. Recombinant hairy-root clones carrying the TwTS overexpression vector were screened by visualising red fluorescent protein; the vector carries the DsRed gene, which can be detected with the LUYOR-3415RG dual-wavelength fluorescent protein viewing lamp. Positive clones were photographed after a period of growth in Petri dishes for phenotypic assessment: whether red fluorescence was present, and how far the hairy roots had bleached.
There are in fact two independent visual signals here, and using them together removes a large amount of unnecessary sequencing:
| Signal | How to read it | What equipment is needed |
|---|---|---|
| Red fluorescence | Fluorescence present = vector integrated and expressed; no fluorescence = untransformed or silenced, discard | Excitation in the GR band (510 - 540 nm) for DsRed plus viewing glasses |
| Root bleaching | Lines with SmCPS1 knocked out show lower tanshinone synthesis and visibly paler roots, so white clones can be picked and then confirmed by sequencing | Routine light photography, recorded in the same session as the fluorescence read |
| Biomass | Weigh and compare after subculture; heterologous routes often cost biomass, so read it together with yield | Balance |
The whole sequence runs: infection and co-cultivation, stepwise reduction of antibiotics for sterilisation, monocloning, fluorescence reading and photographic phenotyping, PCR and sequencing of candidate lines, then yield evaluation. The fluorescence read sits between the third and fourth steps, and it is the fork that decides how many flasks to maintain and how many samples to assay.
Screening hairy-root clones carries three constraints: samples sit in dishes or Erlenmeyer flasks and cannot easily be taken out for slide preparation; the material has to be subcultured afterwards, so observation must be sterile and non-destructive; and dozens of lines are usually handled at once, which makes a sample stage impractical.
| Option | Throughput per batch | Effect on the sample | Where it fits |
|---|---|---|---|
| Fluorescence microscope and imaging system | Low, limited by stage and field of view | Often needs slide mounting, adding contamination risk | Fine imaging and archive images for a few lines |
| Single-wavelength handheld lamp | Medium | Non-destructive | Projects that run a single fluorescent marker |
| LUYOR-3415RG dual-wavelength | High, whole-dish and whole-flask scanning | Non-destructive, back to the incubator after reading | DsRed and GFP material in parallel, large initial screens |
One point is easily missed: the same workflow often involves both GFP and DsRed markers, for example control lines, co-expressing lines or a new vector layered on later. A dual-wavelength unit switches between them on one lamp, so a second lamp is not needed.
DsRed, tdTomato and mCherry are red fluorescent proteins and use the GR band (510 - 540 nm); if GFP material is in the same batch, switch to the RB band (440 - 460 nm). Wear the supplied LUV-30A or LUV-50A viewing glasses while observing; filtering out the excitation light makes weak signals easier to separate.
The unit does not need a darkroom, but hairy roots on medium give a fairly high background. Turn off the ceiling light in the culture room, or shade the area with the supplied light-control cloth, before reading, and keep the reading conditions the same across a batch so that lines can be compared.
At about 150 mm from the sample the beam is roughly 180 mm across, which covers a 9 cm Petri dish in one pass. Raise the lamp to widen the field when scanning a whole tray, and lower it to add light when a line reads weakly. Condensation on the dish lid affects the reading, so wipe it dry before illuminating.
Record results with the LUV series photographic filter (67 mm, direct fit on an SLR) or the phone filter, and file them with the line numbers so they can be matched later against sequencing and yield data. Do not discard lines that read weakly or ambiguously; subculture and read again, or confirm by molecular testing.
| Item | Specification |
|---|---|
| Excitation bands | RB 440 - 460 nm for GFP; GR 510 - 540 nm for DsRed/mCherry |
| Configuration | Any two of five light sources: R, C, G, V, U |
| Beam coverage | About 180 mm diameter at 150 mm from the lamp |
| Unit | Net weight 0.9 kg, total power 27 W, rechargeable battery pack |
| Source life | LED, about 50,000 hours |
| Standard package | Lamp, LUV-30A viewing glasses, LUV-50A viewing glasses, charger, manual, warranty card, aluminium carry case |
| Optional accessories | Adjustable stand, LUV series photographic filter (67 mm SLR fit), phone photographic filter, light-control cloth |
| Operating environment | No darkroom needed; on-site screening in culture rooms and greenhouses |
Not necessarily, but it cuts the downstream workload considerably. With antibiotic selection alone, a fair share of surviving lines still have not integrated the target gene, and confirming all of them by PCR and sequencing is expensive. A fluorescence pass ahead of molecular work narrows the field to positive lines and makes confirmation much lighter.
Either is possible. Expression strength varies between hairy-root lines, and the medium itself contributes some background. Compare the line side by side with known positive and negative controls under the same lighting, re-read weak positives after subculture, and confirm by molecular testing if doubt remains; one reading is a poor reason to discard a line.
Yes. Fluorescence observation is non-destructive, and the material goes back into the incubator for subculture as usual, which is its main advantage over slide-based observation. Even so, avoid leaving a batch under continuous close-range illumination; process the material in batches.
No. The LUYOR-3415RG carries two excitation sources on one body, switched by two separate switches, so a batch containing both GFP and DsRed does not need a change of equipment midway.
Callus, adventitious buds, tissue-culture plantlets, seeds and mature plants in the greenhouse can all be illuminated and observed directly, and the handheld design moves easily between culture room and greenhouse.
It is the same class of equipment. English papers usually write fluorescent protein viewing lamp or excitation light source, while Chinese sources and product pages use excitation light source or fluorescence viewing lamp. For selection purposes, the wavelength and the accessory list are what matter.
LUYOR-3415RG dual-wavelength fluorescent protein excitation light source: the unit used in this paper, RB/GR dual band selectable, net weight 0.9 kg;
GFP fluorescence torches: the full range of fluorescent protein excitation sources, selected by wavelength and illuminated area;
LUYOR-3124RB large-area hanging excitation light source: batch screening of whole trays of plantlets and culture racks;
LUYOR-3421 benchtop fluorescent protein excitation light source: fits a stereo microscope, paired with a handheld lamp for fine imaging;
LUYOR-3280 fluorescent protein viewing torch: rapid screening of single-wavelength GFP material;
LUYOR-3260RB fluorescent protein excitation light source: for projects centred on green fluorescence;
Rice seed fluorescence sorting: LUYOR-3415RG in DMS-TD genic male sterile breeding: another DsRed sorting scenario;
High-throughput initial screening of GFP/RFP transgenics in vivo: options for culture flasks and in-field observation;
LUYOR-3415RG excitation source application cases: more scenarios for fluorescence observation of plant material;
Life science instruments: an overview of laboratory UV and fluorescence equipment.
Compressed to one sentence: pathway design sets the ceiling on yield, while screening efficiency decides how many lines you can try. The S. miltiorrhiza hairy-root route can make both paclitaxel and ginsenoside precursors, and behind that sit three stacked measures - CRISPR knockout, transcription-factor regulation and culture optimisation - each of which depends on DsRed fluorescence to clear out the positive lines. The value of the LUYOR-3415RG here is not replacing an imaging system for publication images but turning this step from mounting slides one by one into scanning whole dishes. To check wavelength configuration, working distance and accessory list against your own material, contact us.
Reference: Lin J., Li W., Liu Y., Yang F., Liang L., Zeng Y., Li Y., Xue Z., French C.E., Guo J., Cui B., Liang Z., and Yang D. (2026). Engineering Salvia miltiorrhiza hairy roots as a scalable platform for high-yield production of paclitaxel and ginsenoside precursors. Plant Communications 7, 101830. DOI:10.1016/j.xplc.2026.101830 (College of Life Sciences and Medicine, Zhejiang Sci-Tech University and others; equipment use described under Fluorescence visualization analysis in the methods)
This article sits in the laboratory research techniques section.
Other sections on the same product line include GFP fluorescence torches (models split by GFP/RFP/DsRed band, handheld and benchtop), semiconductor particle detection (grazing-angle location, fluorescence for organic identification, counting for concentration - three complementary methods) and life science instruments (the entry point for fluorescence imaging, UV crosslinking, UV transmission and cell irradiation).
Models mentioned in this article: LUYOR-3415RG, LUYOR-3124RB, LUYOR-3421. Ranges, accuracy and accessory lists for each model are given on the product pages.
Email: info@xinysun.com
Tel: 131-2093-6518
Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai
Copyright 2026 Xinysun Instrument (Shanghai) Co., Ltd. All rights reserved.
ICP:ICP-2026046447
