Breadcrumb: Home > Applications > Lab Research
Updated:2026-11-17
Views: What separates a UV irradiation chamber from a plain UV lamp, and what do the LUYOR-3550, 3480 and 3450 each measure? This article collects ten frequently asked questions on UV irradiation equipment, covering laboratory irradiation systems, UV crosslinkers and GFP excitation light sources. It sets out how the irradiation chamber, the microplate LED light stimulation source, the cell phototoxicity irradiator, the crosslinker, the 365 nm flashlight and the radiometer divide the work, compares 365 nm and 254 nm lamps, explains photobleaching and dose calibration, and lists the wavelength, dose, sample geometry, control and safety points to check before a system is selected.
Xinyisheng Instruments (Shanghai) Co., Ltd., supplier of the LUYOR range in China This page collects ten frequently asked questions on UV irradiation equipment, covering laboratory irradiation systems, UV crosslinkers and GFP excitation light sources. Read through in order and the selection is settled.
A UV irradiation chamber is a unit that encloses a UV source in a closed cavity and adds controlled timing and dose control, while an ordinary UV lamp is simply the emitter. The difference comes down to three points:
Controllable dose: the chamber sets exposure time or intensity (mW/cm²), so that a defined dose is delivered rather than "left under the lamp for a while" - which is the basic requirement in research and quality control work.
Uniform dose: the cavity is designed so that intensity is consistent across the working area, so differences in exposure between samples do not affect repeatability.
Safety and compliance: the closed cavity keeps UV away from personnel, with a door interlock and automatic shut-off when the door is opened.
Typical applications: light treatment of cells and microorganisms, UV crosslinking of DNA or protein, photocuring of materials, and ageing tests.
LUYOR-3550 is a benchtop UV irradiation chamber whose cavity is sized to hold laboratory animals and batches of samples. It supports UVA/UVB/UVC multi-band combinations and uses an in-cavity sensor to measure the actual dose and hold it constant in a closed loop, which suits light treatment, material photo-ageing and experiments that need a repeatable dose.
For detailed parameters (wavelength, intensity, cavity dimensions), refer to the product page or contact us for the technical data sheet. We can arrange a demonstration and advise on selection - irradiance and cavity size follow directly from your sample volume and experimental design, and a mismatch in either parameter will invalidate the experiment.
This is an LED light stimulation source designed for 96-well or 384-well microplates, a different product category from a UV irradiation chamber, with three levels of difference:
Whole plate, laid flat: the emitting surface is fixed and the plate simply sits on it, so every well receives the same light without repeated adjustment of lamp angle and distance
Wavelength matched to the optogenetic protein: LED wavelengths run from the ultraviolet through to the near infrared (470 nm blue for ChR2, for example), ordered to the excitation peak of the protein you use rather than limited to a single UV band
Fits inside an incubator: the emitting head is thin enough to go into a 37 ℃ humidified incubator for long exposures, which suits live-cell stimulation and optogenetics
Applications: optogenetics and photobiology (activation of ChR2, CheRiff and similar proteins), in vitro cell stimulation, and timed whole-plate exposure. If your aim is cell phototoxicity (3T3 NRU, for example), go straight to the LUYOR-3450 cell phototoxicity irradiator in the next question.
It is used to assess the phototoxicity and photochemical safety of phototherapeutic drugs or cosmetics in cells.
Principle: cells are exposed at a defined wavelength and dose, and the change in viability is measured (MTT, CCK-8, LDH release and so on) to show whether the sample causes cell damage under light. This is a routine test in cosmetic and pharmaceutical safety evaluation, and related requirements appear in EU cosmetic regulation and in several pharmacopoeias.
Compared with an ordinary UV lamp, it provides a quantified dose setting and a consistency guarantee, so results are repeatable and usable in a compliance report.
UV crosslinkers (such as LUYOR UCL-3200 and UCL-3500) use UV exposure to form covalent crosslinks between DNA and protein, for molecular biology work:
Nucleic acid-protein crosslinking (ChIP): studying chromatin structure and protein binding sites
RNA-protein crosslinking (CLIP): capturing RNA-protein interactions inside cells
Antibody-antigen crosslinking: preparing antibodies for immunoprecipitation
How it differs from a UV crosslinking lamp: a crosslinker is a closed cavity with quantitative control, with fixed distance and dose; a crosslinking lamp is an open handheld or bench lamp where the operator maintains distance and timing by hand. For molecular biology work a crosslinker is the recommended choice, because dose consistency feeds directly into repeatability and confidence in the data.
This is a common point of confusion at the selection stage: the wavelengths differ, and so do the uses:
| 365 nm (UV-A, fluorescence inspection) | 254 nm (UV-C, short-wave germicidal) | |
|---|---|---|
| Main use | Fluorescence excitation and non-destructive fluorescent inspection | Sterilisation and disinfection |
| Principle | Organic material on the surface fluoresces and is visible to the eye | Direct DNA damage, microbial inactivation |
| Hazard | Low intensity; prolonged direct viewing has some effect | High; damages skin and eyes, never look directly at the light |
| Typical scenes | Biofilm detection, fluorescent leak detection, cleanliness inspection | Air and surface disinfection in production areas |
The key difference: 365 nm is "light that lets you see", 254 nm is "light you cannot see that kills organisms". Surface contamination checks (biofilm, fluorescent leak detection, cleanliness inspection) need 365 nm - see the 365 nm black light section; 254 nm is for disinfection, and it does not show you where the contamination is.
GFP (green fluorescent protein) and similar proteins are excited at about 395 nm (UV excitation) or 470-490 nm (blue excitation) and emit at about 509 nm (green). But a fluorescent protein needs excitation matched to its spectrum to emit strongly, and excessive UV excitation causes photobleaching - the fluorophore is destroyed and the signal fades quickly.
What a dedicated excitation source does: provide a spectrum matched to the excitation curve of the protein, so that excitation is adequate while the UV component is kept under control, which reduces photobleaching and extends observation time. In practice, over-exposing a GFP sample with an ordinary flashlight makes the signal disappear within minutes, which is a common operating error.
There are also large-area hanging models (such as LUYOR-3124RB) for whole-chamber setups or for handling many samples at once; see the GFP flashlight section for details.
A radiometer measures spectral intensity in the ultraviolet and visible range (usually in mW/cm², μW/cm² or W/m²), and its core use is dose calibration.
Why it is needed: the nominal intensity of a lamp often differs from its actual output, and lamps degrade with operating hours. Periodic measurement of the actual intensity is what keeps the experimental dose repeatable. This step is often skipped in research and quality control work, yet it directly affects whether the data are valid.
Selection points: whether the measurement band covers the wavelength you use, whether the range is appropriate, and whether several bands are needed at once (the XP4000 UV radiometer covers multiple bands, for example). The radiometer itself also needs periodic calibration; see the UV radiometer section.
Treat each wavelength band differently:
UV-C (254 nm and other short waves): high hazard, can cause skin burns and corneal damage. Never look directly at the light; use enclosed equipment or a shield and avoid direct skin exposure during operation
UV-A (365 nm): low intensity and low hazard in everyday use, but do not stare at the lamp for long periods and keep the beam away from people's eyes
UV-B (280-315 nm): intermediate intensity, harmful with long-term exposure
General requirements: before use, confirm that the interlock protection works and that the lamp switches off when the door is opened; staff should wear protective gloves and goggles (especially with UV-C); install UV-C equipment in a well-ventilated area; post warning signs around the equipment; and check cable insulation and seals periodically.
Always read the manual before use and follow local regulatory requirements.
In order of importance:
The wavelength must match the experiment - this is a hard precondition; the wrong wavelength makes the experiment invalid
Dose range and uniformity - whether the target dose is reachable and how much variation there is across the sample
Sample geometry - cavity dimensions and the sample holder (microplate-specific or general tray)
Controllability - timing accuracy, intensity adjustment, dose logging
Safety - interlock protection, light shielding, ventilation
Our advice: write down the experimental protocol (wavelength, dose, sample volume, operating frequency) before choosing. We offer on-site demonstrations, so the setup can be tested under your own sample conditions and you avoid finding out after purchase that it does not fit. The relevant equipment is grouped in the laboratory irradiation systems section and the UV crosslinker section.
For selection advice, sample trials or a demonstration, contact Xinyisheng Instruments (Shanghai) Co., Ltd., supplier of the LUYOR range in China, for UV irradiation chambers, microplate LED light stimulation sources, cell phototoxicity irradiators, UV crosslinkers, fluorescence excitation sources and UV radiometers, with help on method and dose confirmation for your protocol.
This article belongs to the FAQ section.
Other sections on the same product line include UV irradiation chambers and photochemical reactors (quantified exposure for cells, microplates and materials), UV radiometers (mW/cm² intensity and J/cm² accumulated energy - the instrument that shows whether a lamp is compliant) and life science instruments (the entry point for fluorescence imaging, UV crosslinking, UV transmission and cell irradiation).
Models mentioned: LUYOR-3550, LUYOR-3450, LUYOR-3416. Ranges, accuracy and accessory lists for each model are given on the product pages.
Email: info@xinysun.com
Tel: 131-2093-6518
Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai
Copyright 2026 Xinysun Instrument (Shanghai) Co., Ltd. All rights reserved.
ICP:ICP-2026046447
