Breadcrumb: Home > Applications > Lab Research
Updated:2026-11-02
Views: Any cell experiment that involves light runs into one question: how much dose did this exposure actually deliver. The 3T3 NRU phototoxicity test compares viability with and without irradiation, and photosensitizer work compares the response at different light doses; if the exposure conditions are not fixed, the comparison itself loses meaning. This article explains how dose is calculated, how energy mode and time mode divide the work, and how a closed dose loop is implemented, then gives practical setups for three types of experiments. It closes with the operating details that decide whether a result can be repeated in another week.
In cell work, any project that deals with light runs into the same question: how much dose did this exposure deliver to the cells. In a 3T3 NRU phototoxicity test the conclusion comes from comparing viability in an irradiated group and a non-irradiated group; in photosensitizer or photodynamic evaluation what is observed is the difference caused by different light doses at the same concentration. Once the exposure conditions are uncertain, the comparison itself loses meaning - the same sample run on a different day, or by a different operator, may give a result that points the other way.
LUYOR-3450 cell phototoxicity irradiator addresses exactly this step: it turns UV exposure from "find a lamp and shine it" into an experimental parameter that can be set, logged and reproduced. Following the real workflow of a cell irradiation experiment, the sections below explain how it is used in 3T3 NRU phototoxicity, photosensitizer cell evaluation and photo-triggered release, how dose is calculated, and which operating details directly affect the conclusion.
Photobiological effects at the cell level are set by three things together: how much light the test article absorbed, how much energy the cells actually received, and the condition of that batch of cells. The former two have to be fixed by the exposure equipment. Two substitute practices are common in real work, and the problems with each are clear.
UV lamps in a biosafety cabinet or clean bench: the 254 nm wavelength is UV-C, entirely different from the UVA band a phototoxicity test calls for; the intensity also keeps dropping as the tube ages, and there is no dose measurement at all. Such a lamp is designed for disinfection, not as a light source for quantitative exposure.
Solar simulators: the spectrum approaches the full solar spectrum, so UVB and visible light arrive along with UVA, mixing several damage factors into one data set; total power is often around 500 W, with obvious heat output; many models also need an external radiometer for calibration and manual timing.
What the two have in common: you cannot answer "how much was delivered this time". The LUYOR-3450 approach narrows the problem back to the experiment itself - deliver just the band that is needed, just the dose that is set, and keep the sample at a temperature the cells tolerate throughout the exposure.
| Item | Clean-bench UV lamp | Solar simulator | LUYOR-3450 |
|---|---|---|---|
| Spectral range | 254 nm (UV-C) | Full solar spectrum, including UVB and visible light | 365 nm UVA, single band (other wavelengths optional) |
| Power level | Typically 10-30 W | Often around 500 W | About 60 W at full power |
| Dose measurement | None | Many models need an external radiometer | Built-in 365 nm sensor with closed-loop integration, stops automatically at the set dose |
| Sample temperature | Not controlled | Noticeable heat, extra cooling needed | Below 37 ℃ in the chamber, dual-fan cooling |
| Sample fit | No defined sample position | Often large samples or a whole room | Two standard 96-well plates laid flat, several users can work in parallel |
| Operating safety | Exposure risk depends on working habits | Dedicated space and protection required | Interlocked safety door, light cuts off when the door opens |
The scope should be stated at the outset: this instrument covers just the UV exposure step, after sample loading and before detection. Cell seeding, incubation with the test article and viability assays still take place in the routine cell laboratory; what the instrument does is fix the exposure conditions between those steps.
Its standard configuration is 365 nm UVA, 4 × 8 W UV tubes, factory-set intensity 1.7-1.9 mW/cm², adjustable over 1.3-2.5 mW/cm²; two standard 96-well plates fit flat inside the chamber; the chamber stays below 37 ℃ during exposure, matching normal culture conditions so that thermal effects do not enter the phototoxicity result. One fixed program is built in: UVA at 1.69 mW/cm² for 50 minutes, corresponding to the exposure conditions commonly used in the 3T3 NRU phototoxicity test, and it can be called up directly.
Handing exposure to a microprocessor brings two switchable operating modes, and which one you choose directly affects how comparable the results are.
| Item | Time mode | Energy mode (recommended for phototoxicity testing) |
|---|---|---|
| What is set | Exposure duration | Accumulated dose (J/cm²) |
| When tubes age | Actual dose drops, and nothing shows on the display | Exposure time extends automatically, dose stays constant |
| Supply and temperature drift | Shows up directly in the dose | Absorbed by the integration stage, dose unaffected |
| Comparability of results | Conditions must be re-established after a tube or instrument change | Dose can be logged and compared across runs |
| Typical use | When aligning with a fixed duration taken from the literature | Dose-dependent work such as 3T3 NRU and photosensitizer evaluation |
A 365 nm UV sensor sits inside the chamber, with ±5% accuracy, sampling 5 times per second, and the microprocessor calculates the remaining exposure energy from it in real time. In other words, the instrument does not estimate "preset brightness × time" but integrates the measured value inside the chamber - intensity loss from tube aging, chamber contamination or temperature change is compensated automatically. When the accumulated value reaches the set point the exposure stops on its own, with no manual timing and no watching.
This suggests a recording habit worth adopting: write the exposure energy (J/cm² or mJ/cm²) into the method and the record as a formal experimental parameter, rather than writing "irradiated for 50 minutes". With that number, changing the day, the instrument or the operator still leaves a basis for comparison.
These two units are often mixed up in cell irradiation work, and sorting out the conversion saves a great deal of trial and error:
Irradiance is given in mW/cm² and describes how much optical power is received per square centimeter per second;
Dose is given in J/cm² or mJ/cm² and describes the accumulated energy received, with 1 J/cm² = 1000 mJ/cm²;
The relation to time is: dose = irradiance × time. For example, 1.69 mW/cm² for 50 minutes (3000 s) accumulates about 5070 mJ/cm², that is 5.07 J/cm².
That is where the fixed program comes from: the exposure conditions commonly used in the 3T3 NRU phototoxicity test fall in the 5 J/cm² range. In time mode, if tube aging drops the intensity from 1.9 to 1.5 mW/cm², the same 50 minutes delivers 4.5 J/cm² instead of 5.7 J/cm², and nothing about it is visible; energy mode extends the time automatically until the dose is reached.
| Set dose | Time needed at 1.69 mW/cm² | Typical use |
|---|---|---|
| 0.5 J/cm² | About 5 minutes | Low-dose pilot runs, condition finding |
| 2 J/cm² | About 20 minutes | Initial screening of a photosensitizer concentration series |
| 5 J/cm² | About 50 minutes | Usual condition for the 3T3 NRU phototoxicity test |
| 10 J/cm² | About 99 minutes | Photodynamic and photothermal material evaluation, dose-response curves |
This is the standard application for the LUYOR-3450. The complete workflow can be split into four stages:
Before exposure: add the test article to the seeded 96-well plate and complete pre-incubation as the protocol requires; set up a non-irradiated control (on the same plate or a parallel plate) so that the toxicity of the test article itself can be separated from phototoxicity; after switching on, confirm that the set energy or time matches the current protocol.
During exposure: lay the plate flat on the sample position inside the chamber, avoiding stacking and obvious off-centering; confirm the state of the plate lid and well caps as the protocol requires (open or closed, transparent film or not); close the door and start, and the instrument integrates the measured energy inside the chamber and stops at the set point.
After exposure: take the plate out, change the medium as the protocol requires and return it to the incubator; run the viability assay at the specified time point (NRU neutral red uptake or another method); write the actual exposure energy into the experimental record.
Interpretation: compare viability between the irradiated and non-irradiated groups to reach a phototoxicity conclusion; when the same batch of samples is repeated on different days, results are comparable only if the dose is the same.
Photodynamic and photosensitizer studies usually need visible to near-infrared bands to match the absorption peak. Beyond the standard 365 nm, the LUYOR-3450 can be configured with 395 nm, 450 nm, 525 nm, 660 nm, 760 nm, 808 nm and white light. For a two-gradient evaluation of "photosensitizer concentration × light dose", the benefit of energy mode is direct: every well on the same plate receives identical exposure conditions, and the dose difference comes from the parameters you set, not from tube or timing fluctuation.
Using light to control the release behavior of a photosensitive drug or carrier, or to evaluate the heating and killing effect of a photothermal conversion material, calls for a stable, repeatable and gradable light dose. Such experiments often run many parallel conditions, and the 96-well format lines up with the downstream microplate reader workflow. If the system leans toward microplate-level high-throughput screening, or needs blue or green light for optogenetic and photostimulation work, the LUYOR-3480 microplate cell irradiator in the same series is worth reviewing.
Two criteria decide it: where the absorption peak of the test article or photosensitizer lies, and which process the study intends to trigger. The standard 365 nm UVA covers the mainstream needs of in vitro phototoxicity evaluation; photodynamic and photothermal studies usually take 660 nm or 808 nm; optogenetics and blue-light photosensitive systems take 450 nm.
| Wavelength | Band | Common use in cell experiments |
|---|---|---|
| 365 nm | UVA (standard configuration) | 3T3 NRU in vitro phototoxicity test, phototoxicity evaluation of cosmetics and chemical ingredients, photosensitizer cell work |
| 395 nm | Near UV | Near-UV excited photosensitive systems, photoinitiation-related work |
| 450 nm | Blue | Optogenetics (photosensitive protein activation), blue-light photosensitive systems |
| 525 nm | Green | Excitation of specific photosensitive dyes, photoresponsive materials |
| 660 / 760 nm | Red / near infrared | Photodynamic and photothermal therapy research, photo-triggered drug release |
| 808 nm | Near infrared | Photothermal conversion material evaluation, deep-exposure work |
| White light | Visible | Visible-light catalysis, screening of photoreaction conditions |
Lay plates flat, never stack them: an upper plate shadows the sample below it, so the dose that actually arrives is lower than the set value.
Record whether the lid is on in the SOP: the plate lid and well caps absorb part of the UV, so the delivered dose differs with and without them, and the same comparison series must be consistent.
Do not skip the non-irradiated control: without a dark control, the cytotoxicity of the test article itself cannot be separated from phototoxicity.
Record the actual energy, not the set value: in energy mode the instrument compensates automatically, and just the measured value reflects what this batch of samples truly received.
Watch the chamber temperature: during long exposures (50 minutes, for example) thermal effects also affect viability, and a chamber below 37 ℃ keeps this interference low.
Log cumulative tube hours: source life is about 5000-8000 hours, and near the end of life the chamber intensity is worth re-checking by a standard method; energy mode compensates part of the decay, but intermediate checks are still needed.
No long warm-up is needed before the use: dose accumulates from the measured energy inside the chamber, so short-term intensity fluctuation does not change the delivered dose.
| Item | Specification |
|---|---|
| Model | LUYOR-3450 (standard 365 nm; other wavelengths selectable or custom) |
| Power supply | 220 VAC, 50 Hz |
| Power consumption | About 60 W at full power |
| Light source | 4 × 365 nm, 8 W UV tubes |
| UVA irradiance range | 1.3-2.5 mW/cm², factory setting 1.7-1.9 mW/cm² |
| Fixed program | UVA at 1.69 mW/cm² for 50 minutes |
| Energy setting range | 0.025-99.99 J/cm² |
| Time setting range | 0-599.5 minutes |
| Built-in sensor | 365 nm UV sensor, ±5% accuracy, 5 samples per second |
| Chamber dimensions | 26 cm wide × 32 cm deep × 15 cm high |
| Sample capacity | Two standard 96-well cell culture plates |
| Chamber temperature | Dual-fan cooling, chamber below 37 ℃ |
| Dimensions / weight | 31 cm wide × 34 cm deep × 31 cm high; about 10 kg |
| Source life | About 5000-8000 hours |
| Safety design | Interlocked safety door, UV source cuts off when the door opens |
| Control | Microprocessor control, exposure energy and exposure time set independently |
A note on the figures: published channels differ on the tube count and intensity range for the LUYOR-3450 (for example 3 versus 4 × 8 W tubes, 1.3-2.2 versus 1.3-2.5 mW/cm²). The table above lists the standard factory configuration, and the configuration sheet confirmed with the order governs delivery. If the setup has to match existing laboratory conditions exactly, check the details with us before ordering.
The two address different sample types. The LUYOR-3550 UV irradiation chamber covers UVA / UVB / UVC multiple bands and is used for bacterial and cell culture exposure, photostability testing and material aging, a broader set of scenarios; the LUYOR-3450 narrows the band to 365 nm UVA and makes two optimizations for cell work - a chamber below 37 ℃ and room for two 96-well plates laid flat. For in vitro phototoxicity and photosensitizer evaluation, the latter conditions sit closer to what cell experiments need.
The instrument carries a fixed program of UVA at 1.69 mW/cm² for 50 minutes, which corresponds to the exposure conditions commonly used in the 3T3 NRU in vitro phototoxicity test and can be called up directly. The fixed program can also be bypassed, setting exposure energy or exposure time yourself and following an existing validated protocol in your laboratory.
The irradiation chamber measures 26 cm wide × 32 cm deep × 15 cm high and holds two standard 96-well cell culture plates laid flat. With small dishes or other vessels, several groups can be placed inside at one time; the number depends on the shape and arrangement of the vessels.
No. The chamber uses dual-fan cooling and is held below 37 ℃, matching cell culture conditions, so thermal effects do not interfere with the phototoxicity result. This matters in particular during long exposures such as 50 minutes.
A 365 nm UV sensor inside the chamber, with ±5% accuracy, samples 5 times per second, and the microprocessor calculates the remaining exposure energy in real time and stops automatically once the set value accumulates. Intensity changes caused by tube aging, supply fluctuation or chamber contamination are compensated automatically, so the logged dose can be compared and reproduced directly.
No. Exposure energy is measured inside the chamber by the built-in sensor and controlled in a closed loop, which is the instrument's own metrological basis. If the laboratory has separate metrology or intermediate-check requirements, a UV radiometer can be added for periodic comparison as an optional item.
Yes. Beyond the standard 365 nm, configurations of 395 nm, 450 nm, 525 nm, 660 nm, 760 nm, 808 nm and white light are available for photodynamic, photothermal, photo-release and optogenetic excitation needs, and custom builds can follow the experimental protocol. State the purpose before ordering and we will help confirm the wavelength and tube configuration.
Source life is about 5000-8000 hours, clearly longer than the xenon lamps of common solar simulators. The tubes are standard UV tubes, replaceable as a whole unit, and the source position does not need frequent adjustment in daily use. Logging cumulative tube hours is recommended, so that chamber intensity can be assessed against the setpoint after a replacement.
The instrument has an interlocked safety door that cuts the UV source when opened, so the operator and people nearby are not exposed. This is one reason it suits routine cell work better than an open UV source. Even so, do not look into the chamber at the tubes while the door is open, and disconnect power before replacing tubes.
LUYOR-3450 cell phototoxicity irradiator: 365 nm UVA single band, closed-loop energy control, chamber below 37 ℃, quantitative exposure for 3T3 NRU and photosensitizer cell work;
LUYOR-3480 microplate cell irradiator: LED photostimulation in microplate format, suited to optogenetic and high-throughput photostimulation experiments;
LUYOR-3550 UV irradiation chamber: UVA / UVB / UVC selectable, suited to bacterial and cell culture exposure, photostability and material testing;
UV irradiation for bacterial and cell culture: band selection and dose calculation: a review of band and dose conventions for multi-band exposure, useful as a design reference;
Dose setting and control design for photostability testing: dose and control design thinking related to ICH Q1B;
Laboratory irradiation systems section: entry point to UV irradiation chambers, cell irradiators and other UV sources.
The hard part of cell irradiation work is never "is there light", but "how much was delivered this time, and is it the same as last time". Fix the band, set the dose accurately and hold the temperature, and the remaining steps return to the track of routine cell work. What the LUYOR-3450 does here is turn exposure from a step that depends on experience into a parameter that can be written into the method and the record. If your protocol needs confirmation of the wavelength configuration or a starting exposure condition, send us the test article type, cell system, planned exposure conditions and detection method, and we will check them together.
This article belongs to the laboratory research techniques section.
Other sections on the same product line include UV irradiation chambers and photochemical reactors (quantitative exposure for cells, microplates and materials) and life science instruments (the entry point for fluorescence imaging, UV crosslinking, UV transmission and cell irradiation).
Models mentioned in this article: LUYOR-3450, LUYOR-3480, LUYOR-3550. Ranges, accuracy and accessory lists for each model are listed on the product page.
Email: info@xinysun.com
Tel: 131-2093-6518
Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai
Copyright 2026 Xinysun Instrument (Shanghai) Co., Ltd. All rights reserved.
ICP:ICP-2026046447
