Xinysun Instrument (Shanghai) Co., Ltd.

Applications

Breadcrumb: Home > Applications > Lab Research

5-Second UV Curing of Hydrogel Microneedles: Balancing Shape Formation and Viability of Encapsulated Live Cells

Updated:2026-11-02Views:

Microneedle patches have to reach 1000 μm into tissue while carrying live cells, which puts different demands on a curing light source than ordinary photopolymerisation: cure fast, keep the cells alive. A 2025 Cell Biomaterials wound-healing paper used a LUYOR-3109 to cure cyanobacteria-loaded hydrogel microneedles in 5 s, with viability above 80% afterwards. This article explains why the curing window is pushed so short, how the dose is estimated (9000 μW/cm² at 38 cm, so 5 s is about 45 mJ/cm²), how the PEGDA/HMPP formulation and the moulding sequence are set up, how viability is verified by live/dead staining, and where the six common failure points lie.

A microneedle patch has to go 1000 μm down and carry live bacteria with it, and that step makes demands on a curing light source quite unlike ordinary photopolymerisation: cure fast, keep the cells alive. A deep wound-healing paper published in June 2025 in Cell Biomaterials used a LUYOR-3109 benchtop photocatalytic UV lamp to cure cyanobacteria-loaded hydrogel microneedles in 5 s, and viability stayed above 80% after curing. The methods section states it plainly: expose it to UV light (LUYOR-3109, 27 W LED lamp) for 5 s to cure. This article takes that step apart: why the window is 5 s, how the formulation is built, how the dose is calculated, how viability is checked afterwards, and where the process fails.

1. What the paper did

The work was carried out by teams at Tianjin Medical University and Tianjin University (Li et al., Cell Biomaterials 1, 100047, 2025, DOI: 10.1016/j.celbio.2025.100047). For deep wounds such as diabetic foot ulcers and chronic ulcers, the authors built a bilayer pneumatic microneedle patch (CS-MNs): the inner layer encapsulates oxygen-producing cyanobacteria (Cyanothece sp. FACHB-2211), which photosynthesise after application and relieve the hypoxic microenvironment; the resulting oxygen expansion generates pressure that drives sesamin from the outer layer beyond 1000 μm into subcutaneous fat, activating adipocytes to secrete adiponectin and promoting tissue repair.

Results in the diabetic wound model were positive: faster wound closure, lower inflammatory factors, more new vessels. The starting point of that whole chain, however, is a small handling action at the fabrication end - the algae-hydrogel mixture poured into the mould has to set within seconds under UV, and set with the live cells still in it.

2. Why the curing window is compressed to 5 s

Hydrogel photopolymerisation is not fussy about time; a few extra seconds merely over-crosslink. The complication is the live cyanobacteria in the mix:

  • UV damage to algae is dose-accumulative. 365 nm is UV-A: direct DNA damage is weaker than with UV-C, but the dose that generates reactive oxygen species and damages the photosynthetic system rises with time. The longer the exposure, the lower the viability.
  • Curing time buys crosslink density and little else. In a PEGDA system the radicals from initiator cleavage are largely consumed within tens of seconds, so the mechanical difference between 5 s and 30 s is far smaller than the damage that time does to the algae.
  • Heat accumulates as well. The temperature rise under prolonged exposure is modest, but it is still a burden on metabolically active cells.

The design target is therefore not a long exposure but reaching demoulding strength within a dose the algae can tolerate. Five seconds is the experimental result of that balance - the paper verified viability at the same time, finding cyanobacteria still above 80% after curing, which shows the window carries adequate margin.

3. The formulation and workflow in the paper

The methods parameters in order, as a table:

StepParameterFunction
Base solutionPEGDA (average Mw 700) mixed with anhydrous ethanol at 7:3, plus 1% (v/v) HMPP photoinitiatorThe HMPP absorption band covers 365 nm and cleaves under UV to produce radicals that start crosslinking
Algae collectionCyanobacteria suspension centrifuged at 3000 rpm for 15 min, pellet mixed thoroughly with the base solutionRemoves medium, controls water content and algal density
Moulding and degassingMixture injected into the microneedle mould, vacuum for 20 s to draw bubbles out of the needle arrayBubbles starve the tips of material and affect mechanics and penetration
UV curingLUYOR-3109 (27 W LED), 5 s exposure; if unabsorbed liquid remains in the mould, top up and cure for a further 5 sNeedle bodies reach demoulding strength, algal viability retained
Bilayer buildOuter layer of PVA and sesamin pre-cast, air-dried for 6 h, then the algae base solution poured in and cured againDrug in the outer layer, oxygen generation in the inner layer, oxygen drives the drug outward

Two points deserve attention: curing is not a sterilisation step. Five seconds of UV-A will not kill bacterial spores, so sterility of the system depends on filtering the base solution and following aseptic irradiation practice; the 30% ethanol content is itself inhibitory to bacteria, but preparation still has to be carried out in a clean environment.

4. What the LUYOR-3109 contributes to this step

Looking back at why the unit was chosen, several of its characteristics line up with the difficulties of microneedle curing:

FeatureWhat it means for the curing process
9 × 365 nm LEDs, 9000 μW/cm² at 38 cm365 nm falls inside the HMPP absorption band; at 38 cm, 5 s corresponds to about 45 mJ/cm², close to what a PEGDA/HMPP system needs to demould
Square beam 250×250 mm with controlled centre-to-edge intensity differenceA whole microneedle mould fits in the beam at once, so every position in the array receives the same dose and edge needles are not undercured
LED cold source, no direct infraredAlmost no temperature rise in a 5 s exposure, which suits live cells
Instant-on, no warm-upTiming starts at switch-on, and a second-scale process does not wait for the source to stabilise
Continuous 24-hour operation, body at about 50℃Serves as a working lamp in a lab making needles in batches, ready whenever needed

One distinction matters: the illumination that sustains cyanobacterial photosynthesis in the paper was a 32 W/m² full-spectrum LED (380-780 nm), used to compare oxygen output against a natural-light group - that is not the 3109's job. The 3109 handles the 5 s cure at the fabrication end. Curing uses 365 nm, culture lighting uses visible light, and the two sources keep to their own roles rather than being mixed.

The choice of 365 nm rather than 254 nm for this step is not incidental. 254 nm (UV-C) is strongly absorbed by DNA and its lethal dose for cells is one to two orders of magnitude lower than at 365 nm, so a live-cell system cured with it would generally fail a viability check; 365 nm is UV-A, which applies stress mainly through reactive oxygen species, and paired with an initiator such as HMPP, whose absorption band covers UVA, it brings the curing dose inside the window the algae can tolerate. That is why live-cell systems generally choose UV-A LEDs.

5. Estimating the dose: distance, time and measurement

Moving someone else's 5 s onto your own mould starts with a conversion:

  • The 3109 is rated 9000 μW/cm² at 38 cm, i.e. 9 mW/cm². 5 s is about 45 mJ/cm².
  • At about 25 cm the irradiance roughly doubles, so 5 s gives about 90 mJ/cm², but coverage narrows to about 165×165 mm.
  • For a large mould that needs uniform coverage, use the 38 cm rated position; for a small mould and faster setting, work closer for a shorter time.

For practical calibration, work in this order: place the mould at the centre of the beam and fix its position, measure μW/cm² at that position with a UV radiometer, then back-calculate the exposure time from the target dose. Start at half the estimate and add 2-3 s at a time until the needles demould cleanly. Curing is a dose question, not a power question - lamp wattage and irradiance at the sample are two different things, as discussed in the earlier note on UV lamp wattage and intensity requirements.

6. Operating points: from mould filling to demoulding

Against the paper's workflow, a few details decide success when building the process yourself:

  1. Do not skip vacuum degassing. Twenty seconds of vacuum clears bubbles from the needle array; where a bubble stays, material is missing, and the needle breaks there at demoulding.
  2. Top up and cure again. The paper inspects the mould cavities after curing, tops up with base solution where liquid has not been absorbed and cures for a further 5 s, rather than stretching one exposure - the same total dose split in two puts less continuous exposure stress on the algae.
  3. Dry the bilayer before curing. Air-drying the outer PVA layer for 6 h is the precondition for interfacial bonding; shorten it to save time and the two layers separate after hydration.
  4. Demould and hydrate promptly. Dry needles are brittle and recover their mechanical properties after hydration.
  5. Record every batch. Distance, time, batch irradiance and how demoulding felt all go into the record, which is what later viability data can be attributed to.

Do not skip protection: strong 365 nm UV carries a cumulative dose for eyes and skin too, so even second-scale work calls for UV safety glasses and covered wrists, with forceps used to move the moulds.

7. Viability has to be verified after curing

A successful cure does not by itself make the system usable, and the paper provides hard evidence with live/dead staining: DMAO (Ex/Em 503/530 nm) stains all bacteria and EthD-3 (Ex/Em 530/620 nm) stains just those with damaged membranes, counted under a fluorescence microscope and by confocal imaging. Cyanobacterial viability stayed above 80% after curing and was stable over short-term storage; for longer storage the authors suggest moving to lyophilisation with a lyoprotectant.

Reproducing this check needs a fluorescence microscope and a live/dead staining kit, and the reading follows the same logic as bacterial fluorescence labelling experiments. Verify every batch: once the curing conditions change - a new mould, a new distance, a new initiator lot - the viability curve can step down.

8. Six common failure points

SymptomLikely causeWhere to look
Needles tacky, distorted on demouldingUndercured: too far, too short, initiator degradedMeasure irradiance, start at 45 mJ/cm² and increase; store HMPP in the dark
Needles brittle, tips brokenOvercured, or off-ratio formulationShorten the exposure; check PEGDA:ethanol at 7:3
Algal viability below 80%Cumulative exposure too long, repeated exposure, sample warmingUse several short pulses instead of one long exposure; move the sample away between them
Edge needles undercuredMould extends beyond the uniform beamPlace the mould in the central 250×250 mm area rather than lighting one corner
Bilayer interface separatingOuter layer insufficiently driedAir-dry for the full 6 h before pouring the algae layer
Contamination in later cultureCuring mistaken for sterilisationFilter-sterilise the base solution and work in a biosafety cabinet

9. What else this short-cure pattern suits

The specific system here is cyanobacteria plus sesamin, but the process logic is general: any preparation that encapsulates living cells in a photocrosslinked hydrogel faces the same pair of opposing requirements, polymerisation kinetics and cell tolerance. Bacteria-loaded microneedles, algae-loaded beads, cell-sheet hydrogels, and dressings or oral formulations containing live organisms all follow the same approach - choose a band the cells tolerate (365 nm UV-A over 254 nm), use an initiator to shorten the cure, control the temperature rise with a cold source, and verify viability immediately afterwards.

Conversely, if the system contains nothing living, the curing time can be relaxed and the options widen considerably: for small-area spot curing, a more compact model in the gooseneck benchtop UV lamp range is worth considering, and for handheld work that follows the sample, a portable unit such as the LUYOR-3410 fits.

10. How the three 365 nm units divide the work

ModelFormatIntensity (38 cm)Curing scenarios it suits
LUYOR-3109Benchtop, square beam 250×250 mm9000 μW/cm²Whole moulds in one pass, consistency across parallel samples, long batch preparation
LUYOR-3405AGooseneck bench lamp, adjustable head19750 μW/cm²Small-area spot curing, angled illumination into a cavity
LUYOR-3410Handheld (stand available), 4 LEDs6000 μW/cm²Local touch-up, flexible work that follows the sample

All three are 365 nm cold sources; the differences are coverage and freedom of placement. If it is unclear which fits, send the mould dimensions, target dose and batch size and we can check distance and placement together, or leave sample details through contact us.

Related sections and models

This article sits in the laboratory research techniques section.

Other sections on the same product line include laboratory UV lamps (single-tube and dual-wavelength benchtop lamps at 254 / 302 / 365 nm) and life science instruments (the entry point for fluorescence imaging, UV crosslinking, UV transmission and cell irradiation).

Models mentioned in this article: LUYOR-3109, LUYOR-3410, LUYOR-3405A. Ranges, accuracy and accessory lists for each model are given on the product pages.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top