Xinysun Instrument (Shanghai) Co., Ltd.

Solutions

Breadcrumb: Home > Solutions > Speed Measurement

How to Choose a Tachometer or Tachometer Sensor? 12 FAQs Answered

Updated:2026-11-17Views:

How does a tachometer differ from a speed sensor, when should you choose non-contact over contact, and where should you start looking when the reading will not appear? This article answers 12 frequently asked questions: the split between handheld and fixed instruments, laser versus photoelectric sensing, wiring a TTL signal into a PLC, converting rotational speed to linear speed, whether a stroboscope can replace a tachometer, how to apply reflective tape, and how often to recalibrate. Each answer maps directly to a selection decision or a wiring task on site.

Xinysun Instruments (Shanghai) Co., Ltd. - LUYOR supply and service in China. This page collects 12 frequently asked questions about speed measurement: handheld versus fixed instruments, contact versus non-contact selection, troubleshooting a missing reading, TTL wiring to a PLC, linear speed conversion, the division of labor with stroboscopes, reflective tape application, and calibration intervals. Related equipment is listed in the tachometer section and the speed sensor section.

1. What is the difference between a tachometer and a speed sensor?

The two terms are often used interchangeably, but in engineering the distinction is clear:

  • Tachometer (handheld): a portable device you point at a rotating part to get a reading, not permanently mounted. Suited to equipment rounds, spot checks, and troubleshooting.

  • Speed sensor (fixed): mounted on the machine, online long-term, outputting an electrical signal to a PLC or display meter for continuous monitoring and alarm. Suited to cases that feed a PLC or DCS or require trend records.

In one sentence: a tachometer is for "taking a look", a sensor is for "watching continuously".

2. How do I choose between non-contact and contact?


Non-contact (laser/photoelectric)Contact (with measuring wheel)
ContactNoneWheel pressed against the rotating surface
SafetyHigh, suited to high speed and exposed rotating partsRequires shutdown or close approach, with entanglement risk
Measuring distanceRelatively far (hundreds of millimeters)Must be in contact
What it can measureRotational speedRotational speed and linear speed
Typical useMotor shafts, fan main shafts, high-speed gearbox shafts on roundsConveyor belts, rollers, linear speed calibration

If space allows contact and you need linear speed, choose contact; if the target is fast, hard to reach, or must not be touched, choose non-contact.

3. Why does my laser tachometer show no reading?

In order of how often they occur:

  1. No reflective tape on the target surface, or the tape is worn - the most common cause. A laser tachometer calculates speed from the reflected light it receives, and smooth metal reflects too little for a signal. Fix: apply a clean piece of the dedicated reflective tape (most instruments ship with a strip).

  2. Laser incidence angle too large - aim perpendicular or at a small angle; a steep angle loses much of the signal.

  3. Distance beyond range - check the measuring distance range stated for the instrument.

  4. Speed below the lower limit - very low speeds (a few revolutions per minute) need a model designed for low speed.

  5. Strong ambient light interference - sunlight, inverter-driven fluorescent lamps, and proximity to high-temperature furnaces can disturb the photoelectric receiver.

4. How does a stroboscope differ from a tachometer, and can they replace each other?

They do not replace each other; they are complementary:

  • Tachometer: gives the speed as a number (for example 1450 r/min). Answers "how fast".

  • Stroboscope: adjusts flash frequency until the rotating part appears "frozen", letting you see how it runs. Answers "is it running correctly".

Typical sequence: begin with the stroboscope - spotting belt slip, abnormal gear meshing, unusual blade vibration - then measure the actual figure with a tachometer as a baseline. During on-site commissioning, registration control in printing and dyeing, and fan overhaul, a stroboscope often locates the problem faster than a tachometer; see the stroboscope section.

5. What signal does a speed sensor output, and can it connect to a PLC?

The mainstream output is a TTL pulse signal. Take the LUYOR ROLS-5PW as an example: 5 V supply, 5 V TTL output, one pulse per revolution, range 1-300 000 rpm, measuring distance up to 7 m, supplied with a 2.4 m three-core tinned shielded cable - brown to +5 V, black as the signal line, blue to GND, and the shield to the housing. It connects directly to speed display meters, data loggers, vibration analyzers, and stroboscopes.

Yes, it can connect to a PLC, in two common ways:

  • A high-speed counter module (such as the HSC on a Siemens S7-1200, or a Siemens S7-1500) takes the pulse input directly

  • Add a signal converter in between, or use a high-speed counter module to divide the frequency

When wiring, note: do not reverse the polarity (the ROLS-5PW has built-in reverse-polarity and voltage-regulation protection, but check the wire colors before connecting anyway), route the signal cable away from power cables, and ground the shield at one end.

6. Can speed be converted to linear speed, and how?

The instrument always measures rotational speed. Linear speed can be obtained in two ways:

  • Contact: fit a measuring wheel and the instrument converts by circumference to display m/s

  • Non-contact: convert with the formula - linear speed v = π × D × n / 60, where D is diameter (m) and n is rotational speed (r/min)

Example: a roller 0.4 m in diameter turning at 300 r/min has a linear speed of π × 0.4 × 300 / 60 ≈ 6.28 m/s. Some dual-purpose models switch linear speed units directly, saving the manual calculation.

7. How does a panel-mount tachometer differ from a handheld one?

Handheld (such as the LUYOR-925 and PLT200): portable, suited to on-site rounds and spot checks, and it occupies no mounting space.

Panel-mount (such as the LUYOR-910): fixed to a machine panel or control cabinet, read from outside without opening the door. Suited to places where the reading is needed at any time but a handheld is inconvenient.

Smart / transmitter type (such as the LUYOR-912): outputs standard industrial signals such as 4-20 mA or RS485 straight into a PLC or DCS, suited to centralized monitoring.

8. What are typical applications for speed measurement?

  • Motors and fans: checking nameplate speed, judging whether a motor is running correctly, detecting belt slip

  • Printing and packaging: registration drift checks - a stroboscope shows roller runout and registration directly

  • Textile machinery: screening abnormal spindles and speed fluctuation caused by yarn tension

  • Mechanical drives: measuring high-speed gearbox shaft speed, checking coupling alignment

  • Condition monitoring: speed fluctuation is often an early sign of bearing wear, abnormal load, or load imbalance

9. Is speed fluctuation always a fault?

Not necessarily. Common causes: load change (speed drops as motor load rises), supply voltage fluctuation, belt slip (which lowers speed and raises temperature at the same time), loose coupling, bearing wear, and interference on the encoder itself.

How to judge: start with the amplitude and the pattern. A small steady fluctuation (such as ±1%) may be normal load variation; a periodic, violent fluctuation more likely points to a mechanical problem (imbalance, a gear defect); a slow monotonic decline suggests increasing load or belt wear.

10. Is there a right way to apply reflective tape?

Yes, and it directly affects the success rate:

  • Apply it on a flat, rigid, wear-resistant surface, not on a rotating edge or a thin wall

  • The tape should be flat with no bubbles; bubbles cause uneven reflection

  • The laser spot should fall squarely on the tape, held perpendicular

  • Check periodically for wear or oil contamination - worn tape is a common reason for no reading

11. How do I choose between a domestic and an imported tachometer?

To be objective: in this narrow field of speed measurement, the maturity of imported brands shows in the details - the interference rejection of the measurement algorithm, optical coating on the lens, long-term stability, and signal consistency across matched sensors. These differences matter more for online continuous monitoring and data records, and less for occasional rounds.

Our advice: define the use before choosing. If you need nothing more than an occasional reading on rounds, a domestic handheld offers better value; if you need online continuous monitoring, PLC integration, vibration-analysis linkage, or high confidence in the data (for quality certification or ISO audits), an imported option is the safer choice.

Xinysun supplies and supports LUYOR instruments in China, and can provide model comparisons and on-site demonstrations.

12. Do tachometers need calibration, and how accurate are they?

Unlike a contact measuring wheel, a laser tachometer has no wheel wear to cause drift, so it does not need periodic diameter verification the way a wheel does; but if readings go into a quality system (ISO audits, calibration records), periodic checks against a known speed source or a stroboscope are still advisable, and the factory calibration documents should be kept (some models ship with an NIST-traceable certificate).

For contact wheel types, the main error comes from wheel diameter wear and slip, so the wheel diameter should be verified after long use.

For selection advice, demo units, or on-site demonstrations, contact Xinysun Instruments (Shanghai) Co., Ltd. - LUYOR supply and service in China. We provide laser tachometers, panel-mount tachometers, speed sensors, and stroboscopes, and can help confirm wiring, high-speed counter module matching, and on-site installation.

Related sections and models

This article belongs to the Frequently asked questions section.

Other sections on the same product line include Laser tachometers (aim at reflective tape and read RPM, one-handed), Speed sensors (wired to a PLC or DAQ card for continuous monitoring, outputting an electrical signal), and Industrial test instruments (the entry point for UV inspection, rotational speed measurement, stroboscopic observation, and surface inspection).

Models mentioned in this article: LUYOR-910, LUYOR-912, LUYOR-925. Ranges, accuracy, and accessory lists for each model are listed on the product pages.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top