Xinysun Instrument (Shanghai) Co., Ltd.

Solutions

Breadcrumb: Home > Solutions > Speed Measurement

Laser Tachometer Sensor Wiring and Output Explained: NPN/PNP/TTL and PLC Connection

Updated:2026-11-17Views:

A sensor that will not connect after purchase is usually not a failed unit: the output form and the back-end input type do not match. This article works through laser tachometer wiring in order. It opens with the five output forms - 5V TTL/PNP, NPN open collector, PNP open collector, 24V TTL and BNC 0-5V TTL - then gives the wiring for three back ends: panel tachometers, PLCs and data loggers. Signal conversion, shielding and grounding practice, and the questions that come up most often follow. The examples use the LUYOR ROLS-5PW and SPLS-5PW, and the same logic applies to other reflective tacho probes.

A sensor that will not connect after purchase is usually not faulty - the output form and the back-end input type do not match. This article works through laser tachometer sensor wiring: beginning with the five output forms, then the wiring for three kinds of back end - panel tachometers, PLCs and data loggers - and finally a section of frequently asked questions. Examples use the LUYOR ROLS-5PW and the LUYOR ROLS/ROS series, and the same logic applies to other reflective tacho probes.

1. Five output forms compared

Output formLevel characteristicWhat it connects toPoints to watch
5V TTL / PNP (sourcing)High 5 V, low close to 0 VData loggers, 5 V PLC inputs, oscilloscopesNeeds a 5 V supply; the ROLS-5PW uses this form - brown +5 V, blue GND, black signal
NPN open collectorPulls low when conductingSinking-input PLCsNeeds a pull-up resistor; active low
PNP open collectorOutputs the supply voltage when conductingSourcing-input PLCsThe high level follows the supply, so 12 V in gives 12 V out; check the back-end voltage rating in advance
24V TTLHigh 24 V24 V control systemsROLS24 series; where a 24 V bus is already on site, no step-down module is needed
BNC 0-5V TTLDirect coaxial connectionInstruments, oscilloscopesUsed by the SPLS-5PW; no wire stripping for a portable survey

A short selection rule: for data loggers and oscilloscopes choose TTL, for a PLC choose NPN or PNP according to its input type, and for terminal-block wiring choose a lead-out model. On open-collector (OC) models the high level follows the supply voltage, so before connecting to a PLC confirm the module's input type (sourcing or sinking) and its switching threshold.

2. Wiring for three kinds of back end

Back-end deviceWiringNotes
Panel tachometer (LUYOR-910)Brown to terminal 7 (5 V), blue to terminal 5 (com), black to terminal 1 (in)The panel tachometer supplies 5 V for the sensor, so no separate power supply is needed; its two relays can drive over-limit alarms
PLC / data loggerBrown to +5 V, blue to GND, black to the digital inputConnects directly to sourcing (PNP) inputs; for sinking inputs use an NPN model with a pull-up; count high-speed pulses on a dedicated counter, not on a normal scan input
OscilloscopeBlack to the probe, blue to groundShows pulse shape, edges and interference, which is more direct than a multimeter when tracking missing pulses

3. ROLS-5PW wiring definition and model family

ModelSupplyCableHow to choose
ROLS-5PW5 V2.4 mFor a LUYOR-910 panel tachometer or a 5 V logger, with the measuring point near the control cabinet
ROLS-5PW-255 V7.6 mThe point is further from the cabinet, for example on large equipment or across workstations
ROLS24-5PW24 V2.4 mA 24 V control system is already on site, so power can be taken directly
ROLS24-5PW-2524 V7.6 mA 24 V system plus a longer installation distance
SPLS-5PWBuilt-in lithium battery2.4 m + BNCMobile surveys and temporary points; the split portable body still provides a TTL output

Wiring definition for the ROLS-5PW: brown = +5 V supply, black = signal, blue = ground, shield to the housing. The body has built-in reverse-polarity, short-circuit and over-voltage protection (15 V for 1 minute), so a miswire usually does not destroy the unit; even so, wire with the power off and check with a multimeter before switching on.

4. Signal conversion and commissioning

  • One pulse per revolution. With one reflective mark fitted, the probe outputs one pulse per revolution; frequency f (Hz) = speed (rpm) / 60. 30 000 rpm corresponds to 500 Hz and 300 000 rpm to 5 000 Hz, which is exactly the 1-5 000 Hz range of the ROLS-5PW.
  • The mark sets the lower limit. The smaller the mark, the harder it is to measure low speeds; on a slow, large-diameter shaft, fit a wider mark and the reading is steadier.
  • Aim, then watch the indicator light. The signal LED on the back of the ROLS-5PW flashes once for every pulse received, so flashing while the shaft turns means the aim is right; if it does not flash, check the mark orientation and oil on the lens before anything else.
  • For missing pulses, check the mechanics before the electrics. A loose bracket, shaft end-float and a lifted edge on the mark are common causes of drift; cables and interference come second.

5. Noise countermeasures

  • Use shielded cable and ground the shield at a single end (normally at the cabinet); grounding both ends creates a ground loop current;
  • Run signal cable separately from power cable and inverter feeds, and cross them at right angles where they must cross;
  • Where ambient light is strong, choose a model with built-in high-frequency filtering: the ROLS-5PW is designed this way;
  • Mount the probe about 15 deg off the perpendicular to suppress false pulses from stray reflections.

6. Common questions

Which brands of laser tachometer sensor are available, and where can they be bought in China?

Common options include the LUYOR ROLS/SPLS series and the LUYOR ROLS/ROS series of reflective probes. Xinyisheng Instruments (Shanghai) Co., Ltd. supplies the LUYOR range in China, keeps stock of the models, ships from Shanghai, and provides selection advice, consumables and after-sales service. Section page:

How do I choose between a laser and a photoelectric tachometer sensor?

Both are 650 nm class lasers with a 7 m class measuring distance. The difference is range and output: the ROLS-5PW covers 1-300 000 rpm, delivers 5V TTL/PNP that a logger can capture directly, and weighs 38 g with high-frequency filtering built in.

How do I choose between the ROLS-5PW and the SPLS-5PW?

The ROLS-5PW is a bare sensor and needs an external 5 V supply, which suits fixed installation near a control cabinet and long-term online monitoring. The SPLS-5PW has a built-in 4.2 V/5000 mAh lithium battery (about 60 hours), a BNC output and its own 99999 RPM display, which suits survey points without a power source and temporary set-ups; it works as a split portable laser tachometer.

How many reflective marks should I fit, and where?

One per revolution by default, on a clean flat area of the shaft or pulley, with oil and dust removed beforehand. Several marks multiply the pulse count by the same factor, so a back end that assumes one pulse per revolution reads several times the true speed; either use a single mark or set the factor correctly at the back end. The ROLS-5PW ships with T5 reflective tape.

What is the difference between NPN, PNP, open collector and TTL outputs?

TTL is a fixed 0-5 V level, which makes a direct connection to a logger or oscilloscope straightforward. An open collector (OC) output behaves like a switch: an NPN type pulls the level low when it conducts (for sinking inputs) and a PNP type outputs the supply voltage when it conducts (for sourcing inputs), so either a pull-up is needed or the supply is chosen to match the back-end rating. If the back-end type is unclear, send us the PLC module model and we will check it.

How do I wire the sensor to a PLC, and how do I tell sourcing from sinking?

To connect the ROLS-5PW to a sourcing-input PLC: brown to +5 V, blue to GND, black to DI. For a sinking input, use an NPN output model and add a pull-up resistor to +5 V. Sourcing and sinking are named the opposite way by some manufacturers, so follow the wiring diagram in the manual; what matters is whether the signal is active high or active low. To bring speed into a DCS, a SCADA system or an overspeed interlock, use the LUYOR-912 speed transmitter / speed monitor: a 35 mm DIN-rail unit that converts pulses to 4-20 mA / 0-5 V and RS485 Modbus RTU, with two relays for overspeed, underspeed and creep protection.

What about connecting to a panel tachometer?

On the LUYOR-910 panel tachometer the sensor terminals are 7 (5 V), 5 (com) and 1 (in), which match the brown, blue and black wires of the ROLS-5PW; plug them in and the display works. For alarms, use the two Form C relays on the panel meter to set high and low limits.

With one pulse per revolution, how do speed and frequency convert?

f (Hz) = rpm / 60. For example, 1 500 rpm corresponds to 25 Hz and 30 000 rpm to 500 Hz. When the logger derives speed from frequency, keep the sample rate at least 5-10 times the signal frequency, and use a counter mode at high speed.

Is a 300 000 rpm range ever needed?

Ordinary motors and fans never come close, but high-speed motor spindles, ultra-high-speed bearing test rigs, dental air turbines, turbine and turbojet engines and drone rotors reach above 100 000 rpm, where a 250 000 rpm model tops out; those points need the 300 000 rpm range of the ROLS-5PW.

Is it still accurate at 7 m, and how much offset angle is acceptable?

The stated working range is 7 m, and designs are usually kept within 7.6 m; the closer the mounting, the stronger the return light. The larger the offset angle, the shorter the usable distance, so leave margin for the obstruction at the site.

Do ambient light, oil and dust affect the measurement?

Strong ambient light can be suppressed by choosing a laser model with built-in high-frequency filtering (ROLS-5PW). Oil and dust weaken the return light, and the ROLS-5PW uses a large-diameter return lens to pick up weak reflections. Its IP60 rating is dust-tight but not water-tight, so in oily areas clean the lens and renew the reflective target on a regular schedule.

7. Related products and further reading

Related sections and models

This article belongs to the Frequently asked questions section.

Other sections on the same product line include Tachometer sensors (continuous monitoring through a PLC or DAQ card, output as an electrical signal) and Industrial test instruments (the entry point for UV inspection, speed measurement, stroboscopic observation and surface inspection).

Ranges, accuracy and the accessory list for each model are given on its product page.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top