Xinysun Instrument (Shanghai) Co., Ltd.

Solutions

Breadcrumb: Home > Solutions > Speed Measurement

How to Choose a Laser Tachometer Sensor? Laser vs. Photoelectric, Mounting and Wiring

Updated:2026-11-17Views:

A laser speed sensor is a probe fixed beside the machine that outputs a continuous pulse train, and the key difference from a handheld tachometer is that it has no display: it measures an ongoing signal rather than a single reading. This article covers four selection decisions - laser or photoelectric light source, measuring range, mounting distance and offset angle, and output form - using the LUYOR ROLS-5PW as the reference. That model covers 1-300,000 rpm at a 7 m mounting distance with 5V TTL/PNP output, and pairs with the LUYOR-910 panel meter or a PLC. Wiring, reflective tape, and installation points are included, with answers to seven common questions.

A laser speed sensor is a measuring probe mounted permanently beside the machine that outputs a continuous speed pulse. Its key difference from a handheld laser tachometer is that it carries no display of its own and measures an ongoing pulse signal rather than a single reading. Connected to a LUYOR-910 panel-mount tachometer it gives local display and alarm; connected to a PLC or a data logger it supports long-term recording, trend analysis, and overspeed interlock. Selection has to answer four questions: light source (laser or photoelectric), range, mounting distance and offset angle, and output form. This article works through those four in order, with common questions at the end.

A note on terms. By light source, laser speed sensors divide into laser and photoelectric (LED) types; by cable exit, into plug and flying-lead versions; by supply, into externally powered and self-powered. Xinysun Instruments (Shanghai) Co., Ltd. supplies and supports LUYOR products in China, and its current range covers all of these forms. Section page: speed sensors.

1. Laser and photoelectric: start with the light source

The light source decides how far away the target can be, how steeply the sensor can be mounted, and how well it rejects ambient light:

Light sourceExample modelWorking distanceOffset angleCharacter and application
Visible red LEDROS-P/ROS-Wwithin 0.9 m45°Green targeting indicator at the cable end, lower cost; short-range speed measurement in ordinary shops
Incandescent whiteROS-HT-W-250.76 m30°Withstands -25 to 125 ℃, spot landing point visible to the eye; engine bays, dynamometers, and other hot locations

In one sentence: within 1 meter and with budget as the priority, choose photoelectric (LED); beyond 1 meter, with an angled mount or strong ambient light, choose laser. For a more detailed comparison of light sources, see the LUYOR speed sensor selection guide.

2. Four selection steps: range, distance, output, supply

StepWhat to look atHow to decide
1. RangeUpper speed limit of the targetFor ordinary motors and fans a 250,000 rpm range is enough; for motor spindles, dental drills, turbos, and drone rotors choose the 1-300,000 rpm (1-5000 Hz) range of the ROLS-5PW
2. Distance and offsetWhere the sensor can be mounted and whether the beam path is blockedDesign to about 70% of the upper limit as margin; where pipes or guards block the path, a laser version with a 60° offset angle lets the sensor be tucked where it is out of the way
3. Output formWhether the back end is a panel meter, a PLC, or a data loggerFor direct 5V TTL/PNP acquisition choose the ROLS-5PW; for sourcing or sinking PLC inputs choose NPN or PNP by model; for terminal-block wiring choose a flying-lead version. See the full wiring and output guide
4. Supply and accessoriesWhether 5V/24V is available on siteUse the 5V version near a control cabinet; where a 24V bus is present choose the ROLS24 series; at inspection points without power choose the self-powered SPLS-5PW

3. The six models currently available

ModelLight sourceRangeDistance / offsetOutputSupplyFeatures
ROLS-5PW650 nm modulated laser (Class 2)1-300,000 rpm7 m5V TTL / PNP pulse5 VdcBuilt-in high-frequency filtering for ambient light; 38 g, IP60; signal cable extendable to 100 m; online monitoring at very high speed and long distance
650 nm laser1-250,000 rpm7.6 m / 60°Open collector5-24V3.5 mm plug, plugs directly into handheld tachometers, stroboscopes, and the SPSR-IM power module
650 nm laser1-250,000 rpm7.6 m / 60°Open collector5-24VThree tinned leads, straight into the terminal block of a panel meter, frequency converter, PLC, or data logger
SPLS-5PWUses the ROLS-5PW sensor1-300,000 rpm7 mBNC, 0-5V TTLInternal lithium battery, about 60 hours / 115-230VacModule carries its own 99999 RPM display; effectively a split portable laser tachometer that keeps the signal output
ROS-P/ROS-W (photoelectric comparison)Visible red LED1-250,000 rpm0.9 m / 45°Negative pulse3-15 VdcTargeting indicator at the cable end; short range, controlled ambient light, budget-priority situations

Within the same family and form factor there are further supply and cable variants: the ROLS-5PW family covers four combinations of 5V/24V supply and 2.4m/7.6m cable (ROLS-5PW, ROLS-5PW-25, ROLS24-5PW, ROLS24-5PW-25);

4. Quick selection by situation

Site situationRecommended modelReason
High-speed motor spindles, dental drills, turbos, drone rotorsROLS-5PW300,000 rpm range and 5000 Hz bandwidth, TTL/PNP straight into the logger
Measurement point high up or in a hazardous area, out of reachROLS-5PW or ROLS-P/W7-7.6 m mounting distance keeps the sensor out of the hazardous area, with the lead run back to the cabinet
Handheld tachometer plug-in, measure on the spot3.5 mm plug, ready to use
Terminal block wiring, fixed installation inside a PLC cabinetTinned leads crimped straight into the terminals
Inspection points without power, temporary installationsSPLS-5PWSelf-powered with display, BNC straight to the instrument
Engine bays, cooling systems, and other hot conditionsROS-HT-W-25Withstands -25 to 125 ℃, incandescent spot visible to the eye
Ordinary shop, short range, budget priorityROS-P/ROS-WWithin 0.9 m, with targeting light, lower cost

5. Installation and use points

Choosing the right probe is half the job; poor installation still gives unstable readings. A few field notes:

  • Reflective tape is mandatory. A reflective mark has to be applied to the target surface so that one flash lands per revolution; the ROLS-5PW ships with T5 reflective tape and an L-bracket, with a magnetic base available as an option.
  • Closer is better than farther. The distance limit is 7 m, but the nearer the mounting the stronger the return and the better the noise immunity; design the mounting position to within about 70% of the limit.
  • Mount at a slight angle. Roughly 15° off perpendicular suppresses stray reflections from nearby surfaces and from the sensor itself, avoiding spurious pulses out of nowhere.
  • Do not neglect the minimum distance. Leave at least 25 mm between tape and probe; too close causes false triggering.
  • Shield long runs. The signal cable can be extended to 100 m; use shielded cable with the shield grounded at one end, route signal and power cables separately, and keep away from variable-frequency drives.
  • Aiming has a shortcut. The ROLS-5PW has a signal indicator on its back that flashes once per received pulse, so the beam can be aimed without a meter.

6. Common questions

What is the difference between a laser speed sensor and a photoelectric speed sensor, and which should I choose?

The core difference is the light source and the distance, offset angle, and noise immunity that follow from it. Laser versions (ROLS series) use a 650 nm class laser with a fine beam and small spot, hitting the tape reliably at 7 m and 60° offset, which suits long distance, large offset, and strong ambient light. Photoelectric versions (ROS series) use a visible red LED over 0.9 m at 45°, with a targeting indicator at the cable end and lower cost, which suits short-range measurement in ordinary shops. Choose by mounting distance: photoelectric within 1 meter, laser beyond it.

The ROLS-5PW range starts at 1 rpm - can it really measure at the low end?

The 1 rpm lower limit corresponds to about 0.017 Hz, but in practice the low end is constrained by the size of the reflective tape and the pulse counting time, so at very low speeds the reading refreshes more slowly. In engineering terms readings are stable above 10 rpm; below that, enlarge the tape area or use several marks per revolution (noting that the receiving end must be set up for one pulse per revolution).

Can the 5V TTL/PNP output be connected straight to a PLC?

Yes. The ROLS-5PW outputs a 5V TTL-level PNP (sourcing) pulse: connect the brown lead to +5V, the blue to GND, and the black to the PLC digital input. Two things must be confirmed: the PLC input's turn-on threshold is below the output low level, and the input's voltage rating is above the 5V high level. Where the input is a sinking type, use a model with NPN output and add a pull-up resistor. Where 4-20mA, RS485, or relay alarm output is needed, add a LUYOR-912 speed transmitter / speed monitor to convert the pulse into a standard signal for the DCS or SCADA system.

How far can the signal cable be extended?

The standard cable is 2.4 m of three-core tinned shielded cable, with 7.6 m available; with your own extension the total can reach the 100 m class. Any extension must use shielded cable with the shield grounded at one end, routed separately from power cables and drive feeders, otherwise edges soften and noise becomes likely.

Is a Class 2 laser safe, and what should installation take into account?

A Class 2 laser emits less than 2 mW, and under normal conditions the blink reflex is enough to protect the eye, but direct viewing of the beam and viewing the path through optical instruments should still be avoided. In installation, simply point the beam at the target; no extra protective clothing is needed. In routine checks, confirm the bracket is not loose and the lens is not obscured by oil or dirt.

Can it measure without reflective tape?

Not reliably. A reflective probe depends on a reflective mark on the target surface to produce one pulse per revolution; without tape the reading drifts or pulses are lost. Clean the shaft or pulley and apply T5 tape. Where the surface itself has a keyway, a boss, or high reflectivity, the LUYOR MT-190P magnetic sensor is an alternative - ask for a quotation to confirm.

How does a panel-mount tachometer work with a laser speed sensor?

A panel-mount tachometer is a local display and alarm instrument installed into a control cabinet panel, working as a separate unit from the sensor: the sensor at the measurement point outputs one pulse per revolution, and the panel meter handles display, overspeed alarm, and analog output. The LUYOR-910 panel-mount tachometer installs through a panel cutout with a range of 5-999 990 rpm and 0.001% of reading accuracy, dual relay alarms, 0-5V/4-20mA output and optional RS485; connect the brown, blue, and black leads from the ROLS-5PW and it displays immediately.

7. Related products and further reading

Related sections and models

This article belongs to the common questions section.

Other sections on the same product line include speed sensors (continuous monitoring into a PLC or DAQ card, delivering an electrical signal), laser tachometers (aim at reflective tape and read RPM directly, one-handed), and industrial test instruments (the entry point for UV inspection, speed measurement, stroboscopic viewing, and surface inspection).

Ranges, accuracy, and accessory lists for each model are given on the product pages.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top