Xinysun Instrument (Shanghai) Co., Ltd.

Solutions

Breadcrumb: Home > Solutions > Speed Measurement

Drone Propeller Speed Measurement with the ROLS-5PW

Updated:2026-11-02Views:

A UAV propeller does not run at a nominal speed; the speed changes continuously with throttle, voltage and load. A ground test stand has to answer three questions at once: how much thrust and what speed this propeller gives at the present voltage, where the motor and the propeller are matched, and whether vibration or noise comes from the motor or from the blades. Using the ROLS-5PW as the example, this article describes three measurement points on the stand, explains why a frequency-modulated laser is used where sunlight and light flicker interfere, and sets out six typical tests and how speed data is used in each.

A UAV propeller does not run at a nominal speed; it runs at a speed that changes continuously with throttle, voltage and blade load. To reproduce flight conditions on a ground stand, the stand has to answer at least three questions at the same time: how much thrust and what speed this propeller gives at the present voltage; where the motor and the propeller are matched; and whether vibration and noise come from the motor or from the blades. The common precondition for all three is a trustworthy speed reading. This article uses the LUYOR ROLS-5PW fixed-mount laser speed sensor as the example and explains the specific role it plays in propeller and motor stand testing.

Distorted speed data usually comes from the stand environment itself: an open thrust stand in direct sun, indoor runs with LED fill light and mains-frequency lighting, the electromagnetic environment created by brushless motors and ESCs, and blade clamps and fixtures made of bright metal. A probe that skips, counts high or loses pulses under these conditions distorts the thrust-speed curve, and the test has to be repeated. This article treats measurement points, installation, the signal chain and on-site interference rejection as one subject.

1. Why propeller testing cannot do without speed data

Treating speed as one more number on the display wastes what it can do in a test. In the test chain for a UAV rotor system, speed carries at least four functions:

  • The horizontal axis of the thrust-speed curve. A stand maps thrust against speed (some stands also measure torque, giving a torque-speed curve). Without a trustworthy speed the axis means nothing, and the matching point cannot be discussed.
  • The numerator of the efficiency calculation. Shaft power is torque multiplied by speed (P = 2πnT / 60, n in rpm, T in N·m); motor and ESC efficiency and propeller propulsive efficiency all depend on it.
  • The reference frequency for order analysis. When a vibration analyser performs order tracking it needs a speed pulse as the reference, so that the 1× component (equal to n/60 Hz), the 2× component and the blade passing frequency (1× times the number of blades) are aligned to speed. Without that reference the spectrum of a fast rotor cannot be read.
  • The phase reference for dynamic balancing. A balancing machine needs one pulse per revolution as the angle reference when it calculates the phase of the unbalance; if the speed signal jitters or drops out, the phase is wrong.

There is another requirement that is often underestimated: batch consistency. Fit the same batch of blades and the same batch of motors to the same airframe, and the spread in speed reflects blade geometry deviation and motor reluctance differences - a ready-made indicator for incoming inspection and line sampling.

2. Three measurement points for the ROLS-5PW on a test stand

On one propeller, the choice of measurement point decides which speed you read. A stand usually offers three positions, each with its own purpose:

  • Motor shaft end (the speed reference point). A reflective target on the motor output shaft or coupling gives the motor shaft speed. This is the standard reference for cycle, efficiency and order analysis, and the default point on most stands.
  • Propeller hub / blade root (the actual speed point). With the target on the hub or at the blade root near the shaft, the reading is the speed at which the propeller itself turns. Where a reduction, coupling or tensioning stage sits between motor and propeller, shaft speed and propeller speed differ, and comparing the two shows whether that stage slips or loses energy - something often overlooked on small direct-drive propellers.
  • Stand main shaft / fixture shaft. On a multi-station stand, or one driving several power sets at once, the fixture shaft speed tells you whether the whole fixture is stable and running true.

Why a laser rather than an ordinary photoelectric probe: propeller speeds reach the ten-thousand-rpm range, and the stand has strong light from motors and ESCs plus reflections from drives and fixtures. The ROLS-5PW uses a 650nm frequency-modulated laser (Class 2, output below 2mW) with a built-in high-frequency filter and a large-diameter receiving lens, so a weak return is still received reliably in strong ambient light; the measuring range reaches 7 m, so the sensor can stand outside the safe distance and nobody needs to approach the measurement point while the propeller is turning.

3. Strong light, flicker and electromagnetic interference: why propeller stands use a modulated laser

The four kinds of interference on a propeller stand arrive together, and dealing with one of them alone is rarely enough:

  • Direct sunlight. An open thrust stand or an outdoor test pad has no shade, and at midday ground reflection and direct sun enter the probe field together.
  • Indoor light flicker. Mains-frequency lighting and some LED fill lights ripple at around 100 Hz, right next to the band of the speed pulse.
  • Motor and ESC electromagnetic interference. Brushless commutation and ESC PWM couple spikes onto the signal line, more so over a long cable.
  • Reflections from metal fixtures. Blade clamps, guards and stand extrusions are bright surfaces, and stray reflections are easily counted as target returns.

A conventional photoelectric probe (including most laser-diode types) judges by return intensity: a reflection above the threshold counts as a pulse. That works in a laboratory and fails on a stand - sunlight is far brighter than the target return, the light ripple every 10 ms is enough to cross the threshold, and stray reflections from metal are counted too. The symptom is a reading that jumps, a pulse count that runs high or drops pulses, a curve drawn with sawtooth edges, and two runs of the same condition that do not agree.

The ROLS-5PW replaces that criterion: the laser is emitted at a fixed modulation frequency and the receiver demodulates that frequency alone. Sunlight, room lighting and indicator lamps on neighbouring machines do not carry that frequency signature and are rejected in the filter stage, leaving the signal that genuinely comes from its own target. That is why it still reads steadily on an open stand in outdoor sunlight.

ComparisonConventional photoelectric / intensity thresholdROLS-5PW modulated laser
Identification basisWhether the return exceeds an intensity thresholdWhether the return carries the modulation frequency the sensor emits
Direct sunlightSunlight is brighter than the target return, so the threshold cannot discriminateSunlight does not contain that modulation frequency and is rejected by the filter
Indoor flicker and fill lightPeriodic brightness crosses the threshold, producing regular false triggersNon-modulated frequencies never reach the demodulator
Nearby metal reflectionsStray reflections from bright surfaces can be counted as pulsesAccepts its own modulated light; stray reflections are not demodulated
Working distanceTypically of the order of 1 m7 m nominal (use within 7.6 m)
Weak return at high speedThe return is extremely short and low in energy, easily missedA large-diameter collecting lens with high-frequency filtering still identifies it
Output formMostly a switching output, needing reshaping5 V TTL/PNP pulses, feeding data acquisition, panel meters and PLCs directly

Two physical factors are often overlooked. One is return time at high speed: at ten-thousand-rpm the target crosses the beam in a few tens of microseconds, the return energy is low, and catching it takes a collecting lens with narrow-band demodulation. The other is aerodynamic fidelity from non-contact measurement - the probe does not touch the shaft and does not enter the propeller disc flow, so it adds no load to the object and does not change the flow near the blades, and the thrust and torque figures are the true behaviour of that propeller.

The 7 m range has extra value on a UAV stand: the sensor can be mounted outside the plane of rotation and behind a guard net, so nobody approaches the measurement point while the propeller is turning, and when the stand is modified or the propeller changed the probe position does not have to be reworked.

4. Six typical tests and how speed data is used

1. Mapping the thrust-speed curve on the stand

Start from low throttle and load up in steps, recording thrust and speed at each steady point, then plot the curve. The shape of the curve drives the selection strategy: a shallow climb means the blade is inefficient in that range; if thrust stops rising, or falls back, beyond a certain speed, the propeller has entered stall. The curve is also the basis for motor-propeller matching - the point where the motor characteristic crosses it is the sensible operating point.

2. Motor-propeller matching and efficiency optimisation

Both the motor efficiency curve and the propeller efficiency curve need speed data before they can be drawn. The aim of optimisation is to find the efficiency peak within the usable speed range by superimposing motor efficiency on propeller efficiency, rather than looking at full throttle alone. Record thrust, torque and input voltage and current in step with speed, and the losses can be apportioned across motor, ESC and propeller.

3. Order analysis and vibration location

Feed the speed pulse into the speed channel of a vibration analyser and the rotational components in the spectrum, including the blade passing frequency, are aligned to speed automatically. A high 1× component usually points to imbalance or misalignment; a peak near the blade passing frequency relates to blade count and stiffness; fractional orders suggest interference or resonance. If the speed reference is wrong, none of this reading is possible - for the reasoning behind harmonic interpretation, see stroboscopic observation of high-speed moving objects.

4. Dynamic balancing and the phase reference

On a balancing stand the sensor supplies one pulse per revolution as the phase reference, and the machine uses it to calculate the phase angle of the unbalance and propose a correction. A stand measuring propellers also needs suitable fixturing and a steady speed segment; take the reference from the steady segment, not from acceleration or deceleration.

5. Propeller integrity inspection

Once a blade has a crack, coating loss or edge damage, its mass distribution changes and the imbalance response at a given speed changes with it. On the line or in maintenance, combining a confirmed speed reference with stroboscopic visual inspection finds the abnormal part without dismantling it; for the stroboscopic side see predictive maintenance and stroboscopes and speed and stroboscopic inspection for industrial equipment.

6. Ground runs and pre-flight checks

A ground run with the propeller fitted has to confirm that the actual speed falls in the expected range. This is where a fixed-mount sensor shows its value: mounted once, nobody has to hold a handheld meter near the blades for the whole run, and the reading can go straight to a display or a data acquisition system for logging and over-limit alarms.

5. Installing the measurement point: target, distance and angle

  • Put the reflective target on the shaft, not on the blade. Place it on the motor shaft, the coupling or the root of the hub; on the blade surface the blade itself blocks the beam every revolution and pulses are lost, so the reading jumps.
  • One target gives one pulse per revolution. With a single target the back end is scaled as 1 pulse/rev; more targets raise resolution but the "pulses per revolution" setting at the back end must be changed to match, or the speed is multiplied. The relation is f (Hz) = n ÷ 60.
  • Design the distance at about seventy percent of the limit. The ROLS-5PW reaches 7 m and is recommended for use within 7.6 m; the return weakens with distance, so leave margin in harsh or oily conditions. Keep at least 25mm between target and probe - closer than that causes false triggering.
  • Mount at about 15° off perpendicular. A slight tilt lets the sensor receive the return from the target while suppressing stray reflections from surrounding surfaces and from itself; this angle is the key to rejecting false pulses.
  • Fix it with the L-shaped bracket. The bracket is standard and a magnetic base is optional; a loose bracket or an end-floating shaft is a common cause of drifting readings, so check that everything is tight before a test.
  • Watch the environmental conditions. Operating temperature -10 to 50℃, protection rating IP60 (dust-tight, not water-resistant). Outdoor stands need extra cover in the rainy season and in winter cold; a test pad in long sun benefits from a sunshade, and the target should be kept clean.

6. How the signal gets out: pulses, panel meter, four channels and host logging

The ROLS-5PW outputs a 5V TTL PNP pulse; brown is +5V, blue is ground and black is the signal. That pulse chain can go in three directions as required:

  • To a panel tachometer: the LUYOR-910 panel tachometer covers 5-999990 RPM, can power the sensor directly, shows PV/SV on a six-digit LED display, provides two Form C relays for high and low alarms, and offers optional 0-5Vdc or 4-20mA analogue output and RS485 (Modbus RTU) communication. It suits a stand with one operator: an over-speed condition trips a relay to cut thrust or raise an alarm.
  • To data acquisition and a host computer: the pulse goes into a high-speed counter channel to record the full speed curve for efficiency mapping and order-analysis post-processing. Screened cable is standard at 2.4m with 7.6m optional, the signal cable can be extended to 100m, and any extension should be screened cable with a single-point ground, routed separately from power cables.
  • Four-axis synchronous acquisition: four motors on a multirotor frame, or several power sets driven on one stand, need several speeds read at the same instant for comparison. One LUYOR-904 four-channel speed acquisition system takes four ROLS-5PW sensors, shows four colour curves on one screen, sets pulses per revolution and alarm limits per channel, and exports CSV/Excel and statistical reports, which avoids the old problem of several single meters with time bases that do not line up.

Where blade phase, spacing and rotation need visual confirmation, a stroboscope works alongside the speed measurement: the LUYOR-906L laser-tracking stroboscope sets its own rate from the rotating pattern and makes the propeller appear "still", which makes tip path and any interference or rubbing easy to see.

Signal path five: continuous host recording, storage and replay

What actually takes time on a test stand is running the whole envelope and then going back to analyse it, so the acquisition side has to record continuously rather than show an instantaneous reading. Route the ROLS-5PW pulse into host acquisition software (or upload through the RS485/Modbus RTU of the LUYOR-904 four-channel system or the LUYOR-910) and three things follow:

  • A timestamped speed history. Throttle steps, load changes and long steady-state runs are recorded end to end and saved automatically, then replayed by time segment instead of being copied down by hand.
  • Curves on the same base as thrust and torque. The speed channel shares one time base with the stand's thrust, torque, voltage and current channels, which is what makes speed-thrust and speed-efficiency curves possible and lets losses be apportioned across motor, ESC and propeller.
  • A phase trigger signal. One pulse per revolution serves directly as the phase reference for a balancing instrument, so the calculated correction angle stands up.

The output is a standard TTL pulse that mainstream acquisition cards, data loggers and PLCs accept directly; when integrating into an in-house stand, confirm the input type (PNP source into a sinking input) and the level match (5 V TTL into a 24 V digital module needs conversion, or choose the 24 V supply version). Wiring detail is in laser speed sensor wiring and outputs explained.

7. In practice: UAV powertrain development and university laboratories

The same sensor is used at different stages by airframe manufacturers, eVTOL teams and university laboratories: manufacturers care about batch consistency and line cycle time, eVTOL teams about personnel safety distance and data traceability, laboratories about range coverage, channel count and budget. What they share is that nobody wants a person holding a meter next to a fast-turning propeller.

Organisations already using these sensors in volume for propeller and rotor speed measurement include the aerospace power laboratories of CH UAV (Aerospace CH UAV), XPENG AEROHT (eVTOL), Nanjing University of Aeronautics and Astronautics, Tsinghua University and Beihang University.

The names above indicate the actual application range of the product; project details remain subject to agreement between the parties, and permission should be confirmed before any long-term public reference.

The practice in these settings is very similar: the probe is fixed to the side of the stand or outside the guard net, aligned once and left alone for the whole test campaign; speed goes into the acquisition system and is logged synchronously with the thrust channel, and abnormal conditions are located by replay; changing a propeller or a motor means moving the target, not the sensor. That is the difference between a fixed probe and a handheld meter, and the precondition for a long test campaign to run continuously.

8. Core advantages and typical applications at a glance

  • Modulated laser rejects light interference. It demodulates the return at its own modulation frequency, so direct sun, indoor flicker and stray light from neighbouring machines are filtered out, indoors and outdoors.
  • Non-contact measurement does not disturb the flow. It does not touch the shaft or enter the propeller disc flow, so thrust and torque are free of added load.
  • Continuous host recording. Long acquisition, automatic storage and replay by time segment, plotted on the same base as thrust and torque.
  • Long distance and wide range. 7 m nominal range, 1-300 000 rpm (1-5 000 Hz), covering everything from low hover speeds to high-speed rotor conditions.
  • Standard pulses, easy integration. 5 V TTL/PNP output connects directly to acquisition cards, loggers, PLCs and panel tachometers.
  • An installed base in UAV powertrains. Airframe manufacturers, eVTOL teams and aerospace university laboratories use it in volume.

Typical applications

UAV thrust test stands, propeller dynamic balancing, motor-propeller matching and calibration, ESC speed-control performance testing, multirotor synchronous speed acquisition, wind-tunnel rotor tests, university aerospace power laboratories, and end-of-line quality checks on production powertrains.

Equipping one stand

Stand requirementRecommended configurationKey points
Speed display with over-limit alarmROLS-5PW + LUYOR-910 panel tachometerThe panel meter can supply 5 V to the sensor; its two relays drive an audible/visual alarm or an interlock stop
Four-rotor or four-station comparisonROLS-5PW ×4 + LUYOR-904 four-channel acquisition systemOne time base, four colour curves on one screen, pulses per revolution and alarm limits set per channel
Integration into an in-house stand or PLCThe TTL/PNP pulse from the ROLS-5PW connects directlyPNP source output into a sinking input; 5 V into a 24 V digital module needs conversion or the 24 V supply version
Long-term outdoor installation, rainy seasonROLS-5PW + waterproof junction box and sunshadeThe body is IP60, dust-tight but not water-resistant; probe and terminals need secondary protection
Temporary points, no fixed supply on siteSPLS-5PW self-powered moduleBuilt-in battery about 60 hours, BNC output, integral display

9. Frequently asked questions

Should propeller speed be measured with a contact or a non-contact probe?

For stand testing, always non-contact. Contact types (magnetic, Hall) need the probe mounted at the shaft end or coupling, where the contact face and mounting concentricity affect the reading directly, and fitting and removal are awkward; laser and photoelectric probes work from a reflective target, go on and come off quickly, can be moved, need no realignment when the measurement point changes, and measure at a distance on fast-turning parts that a person cannot approach.

The blades turn very fast - is an ordinary photoelectric speed sensor adequate?

In most cases it is not. Photoelectric (LED) types usually work within about 1 m and within 45° off axis, and outdoors they need additional filtering or modulation; at high speed the return from the target is also weaker. A laser type has a fine beam, longer range and wider off-axis angle, and with high-frequency filtering it resists ambient light, which makes it the usual choice for high-speed propeller work. For a selection comparison see laser speed sensor selection guide.

Four motors on a multirotor have to be measured together - is four-channel equipment necessary?

It is. Uneven motor speeds bring attitude and efficiency problems, and measuring one machine at a time cannot compare sequence or amplitude within one run. Four-channel synchronous acquisition gives four curves and their differences at once, and with independent alarms per channel it points straight to the channel at fault; wiring and software are covered in LUYOR-904 four-channel speed acquisition system.

Do more reflective targets improve resolution?

Yes, but the pulses per revolution must be set to match. With 4 targets each revolution gives 4 pulses, and if the back end still scales as 1 pulse/rev the reading is multiplied by 4. Where high resolution is needed, prefer a measurement point that already gives multiple pulses per revolution (a toothed disc or an encoder wheel) and keep reflective targets for temporary work.

Should the target go on the blade or on the shaft?

On the shaft - motor output shaft, coupling or the root of the hub. On the blade surface the blade blocks the beam on every pass, pulses are lost and the reading jumps, and order analysis is especially sensitive to this. To measure the true propeller speed, add a second probe on the hub and compare it with the shaft speed.

Can an outdoor stand be used in the rain?

The ROLS-5PW is rated IP60, dust-tight but not water-resistant, and the signal cable and terminals must also be kept out of the rain. On an outdoor stand, add a waterproof junction box and a sunshade, and in rain move the sensor and cabling under a roof before continuing; for a permanent outdoor installation, arrange the probe and cabling under a roof or give the connections secondary protection so that the terminals do not stay damp.

Can a laser speed sensor measure accurately on a stand in direct sunlight?

It can, provided a modulated laser type is chosen rather than an intensity-threshold type. Sunlight is far brighter than the target return, so a probe that judges by intensity largely fails in direct sun; the ROLS-5PW demodulates its own modulation frequency and sunlight, lacking that frequency, is filtered out. Two things still matter in use: keep the target clean, since oil and dust weaken the return, and fit a sunshade on the probe to extend its life - the body is IP60, dust-tight but not water-resistant, so in rain it has to move under a roof.

How is speed data recorded over the long term and replayed afterwards?

Three routes: the pulse goes into a high-speed counter channel or a data logger and the acquisition software saves it with timestamps; it is recorded through the LUYOR-904 four-channel system with four curves on one screen and export to CSV/Excel and statistical reports; or it is uploaded through the RS485 (Modbus RTU) of the LUYOR-910 panel meter. All three put speed on the same time base as thrust and torque for post-processing, which matters especially for throttle steps and load changes - otherwise the curves can be aligned by hand annotation alone.

Related products and further reading

Conclusion

The accuracy floor of a UAV propeller test depends on whether the speed reference is trustworthy. A fixed-mount laser speed sensor such as the ROLS-5PW settles three things at once: the 7 m range keeps people at a safe distance from a fast-turning propeller, the pulse output feeds panel meters, four-channel acquisition and vibration analysers directly, and the 1-300 000 rpm range covers the speeds of everything from agricultural blades to racing quadcopter propellers. If you need measurement-point planning and wiring confirmation for a specific stand, contact the Xinyisheng technical team for a proposal.

Related sections and models

This article belongs to the speed and stroboscopic measurement section.

Other sections on the same product line: laser tachometers (aim at a reflective target and read RPM, one-handed), speed sensors (wired to a PLC or acquisition card for continuous monitoring, delivering an electrical signal) and stroboscopes (freezing rotation and reciprocation by persistence of vision, to see the process rather than a number).

Models mentioned in this article: LUYOR-910, LUYOR-ROLS-5PW, LUYOR-906L. Range, accuracy and accessory lists for each model are given on the product pages.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top