Xinysun Instrument (Shanghai) Co., Ltd.

Solutions

Breadcrumb: Home > Solutions > Fluorescent Inspection

In Fluorescent Penetrant Inspection, the Blacklight Covers Step 5: How to Use the LUYOR-3103/3103D for Penetrant Testing

Updated:2026-11-02Views:

In fluorescent penetrant testing, the penetrant is half the method: if the lighting fails, the whole sequence is wasted. This article places the LUYOR-3103/3103D black light inside the five steps of penetrant inspection and compares it with the standard requirements for intensity and wavelength, the working distance and white-light discipline of step five, and how the P and D versions are chosen by power source. It also shows when a different model fits better, including the 3115 for large areas, the BB series for wet and dusty sites, and the 3180 for locating small indications.

In nondestructive testing, fluorescent penetrant testing (FPT/LPI) covers a wide range of materials: aluminum, titanium, ceramics, plastics and glass, as long as the part is not porous. Its dependence on the UV lamp runs deeper than many new inspectors expect. A good penetrant is wasted if the lighting fails, and the whole sequence fails with it. Drawing on the standard requirements and process points collected in Spectro-UV's published penetrant testing material, this article places the LUYOR-3103/3103D black light inside the five steps of fluorescent penetrant testing, shows what it covers, and explains when another lamp fits better.

The five-step sequence, and why the black light owns step five

StepWhat happensKey point
1. Pre-cleaningRemove oil, scale, developer residue and other contamination from the surfaceContamination blocks defect openings or interferes with penetrant; skip this and everything after it is wasted
2. Apply penetrantFluorescent penetrant covers the surface and dwells 5–30 minutes to enter open defectsDwell time follows material and defect type; extend it when the part is cold
Remove excess penetrantKeep penetrant inside the defects and nothing elseOver-washing takes penetrant out of the defects and creates misses
Apply developerThe white developer layer draws penetrant back to the surface like blotting paperToo thick a layer dilutes the indication
UV observationInspect under UV-A black light in a darkened area; defects fluoresce yellow-greenThe main subject of this article is this step: lamp intensity, wavelength and white-light control decide whether an indication can be read

Fluorescent penetrant's advantage over visible red dye lies in contrast: a yellow-green indication sits on a nearly black background, while a red dye indication has to compete with a white developer under white light. A contrast difference of an order of magnitude means cracks an order of magnitude narrower can be seen - which is why aerospace specifications generally mandate fluorescent penetrant. The experience reported in the source material: the fluorescent method can reveal finer cracks and tighter openings, indications hidden by shadow in complex geometry, dense small indications that blend together under white light, and linear indications that point to fatigue cracking; defects just a few micrometers wide may still be detected.

What the standards ask of a black light, checked line by line against the 3103

Penetrant standards such as ASTM E1417 and aerospace specifications set four groups of requirements for UV lamps. Set beside the published figures for the LUYOR-3103 series, they form a ready conformity table:

Standard requirement (ASTM E1417 and aerospace practice)LUYOR-3103 seriesResult
UV-A intensity at the workpiece surface not below 1000 μW/cm²; some specifications ask for more than 1500 μW/cm² on critical parts4500 μW/cm² at the center, 380 mm from the lampWell above the threshold; inspection distances are often shorter than 38 cm, so the workpiece sees more
Ambient white light held below 20 lux to protect contrastWork in a darkroom or fully darkened area; the white LED in the head has its own switch and stays off during interpretationBlack light to find indications, white light to mark them; the two do not interfere
Wavelength inside the UV-A band (320–400 nm, peak near 365 nm), with no excess UV-B/UV-C365 ± 5 nm, with a black filter at the front that cuts visible and short-wave contentFilter fitted at the factory, no extra part needed
Large workpieces require reasonably uniform intensity across the covered areaFlood spot of about 200 mm diameterOne lamp covers one area at a time; for larger areas see the model split below

Two notes at model level: the series meets ASTM E3022 (UV-A LED lamps for fluorescent penetrant and magnetic particle testing) and GB/T 5097-2020 (non-destructive testing - black lights); and where a process document is written to 4000 μW/cm² with the filter supplied as standard, the 3103PL/3103DL derivatives use the same optical path.

Running step five: distance, rhythm, white-light switching

Enough output gets you through the door; three things decide whether the step works:

  • Distance and coverage belong together. The 4500 μW/cm² figure is the center value at 38 cm. Move closer and the workpiece sees more, but the spot narrows; when sweeping, hold a roughly fixed distance (30–40 cm) and step along so that spot edges just meet, rather than backing off to save time - intensity falls faster with distance, and small indications slip away at the edge of the spot.
  • Sweep rhythm and eye adaptation. Fluorescent indications need dark adaptation, so give the eyes a few minutes in the dark area before interpreting. On long shifts, plan the route by area to avoid missed and repeated zones. The source material's warning that many small indications blend together under white light applies in the dark area as well: when indications are dense, confirm them one at a time before recording.
  • White LED switching. The 3 W white LED in the 3103 head is for what comes after an indication is found: marking, photographing, recording. White light must be off while reading fluorescence - the lower the ambient white light, the better the contrast, and that is where the 20 lux threshold comes from. The normal rhythm is: black light to find the indication, black light off and white light on to mark it, then back to black light to continue.

P version or D version: choose power by site

The 3103 and 3103D share the same UV-A output and optical path; the difference is the power supply:

ModelPowerSuited to
LUYOR-310324 V power adapter (mains)Fixed stations, in-process checks between machining steps, maintenance shops
LUYOR-3103D24 V lithium battery packWeld sites, tank interiors, work at height and places without a convenient outlet
3103PL/3103DLSame two power options, UV-A output 4000 μW/cm², filter supplied as standardSites whose process documents are written to 4000 μW/cm²

Instant-on LED light is a real efficiency point in penetrant testing: mercury lamps need 5–15 minutes of warm-up before output is stable, while an LED reaches working intensity as soon as it is switched on, so interleaved jobs and frequent moves do not involve waiting. A solid-state source also tolerates knocks and vibration, and with the D version's battery it stands up better on site. The source material's note that LED output stays more stable over its life carries a second meaning: when intensity is measured on schedule, LED readings drift less, so the check records stay consistent more easily.

When the 3103 is not enough: how three models divide the work

The 3103's 200 mm flood spot covers most workpieces, but two situations call for another lamp:

SituationRecommended modelReason
Large structures, rows of welds, lifting work facesLUYOR-3115 hanging type (15 LEDs, 9500 μW/cm² at 38 cm)Large-area lighting at a fixed station, one pass covers more
Long sweeps outdoors, in damp or dusty conditionsLUYOR-BB series (8 LEDs, BBH/BBM/BBL three levels, IP68)Larger spot plus a high ingress rating for harsh sites
Locating and confirming small fluorescent indicationsLUYOR-3180 spot type (about 40000 μW/cm² in a small spot at 38 cm)After the flood lamp finds a suspected indication, the spot lamp at closer range resolves it

A common combination: a 3115 on the station for full inspection, a 3103D carried for re-checking and marking, and a 3180 for difficult indications - three intensity levels matching three depths of interpretation, which is more efficient than forcing one lamp through everything.

Lamp management: half of the penetrant quality record lives here

The source material spends a whole section on calibration and checks, which in daily practice comes down to four actions: check the filter for cracks and the lamp head guard for damage before each shift; measure intensity at a fixed distance with a UV radiometer on schedule and record it, sending the lamp for service or replacement when the reading falls noticeably; send the radiometer itself for calibration on schedule; and put every intensity reading into the quality record. Day-to-day care for the 3103 adds one item - wipe the filter and the aluminum heat-sink surface with a soft cloth, since developer dust on the heat sink affects cooling. On the personnel side, penetrant interpretation should be done by certified staff (ASNT SNT-TC-1A or NAS 410 schemes); that is the other line, alongside the lamp.

Limits of the method: what the black light cannot do

Fluorescent penetrant testing responds to surface-breaking defects; buried defects call for ultrasonic or radiographic methods. Porous and rough surfaces (as-cast, shot-peened) adsorb penetrant and produce false indications, so interpretation has to take surface condition into account. Pre-cleaning quality directly sets the detection rate, and penetrant, remover and developer waste must be handled to procedure. These limits have nothing to do with the lamp, but they belong in the inspection plan: the source material lists poor surface preparation and contamination blocking defects among the main causes of missed indications, which is worth writing into the work instruction.

Frequently asked questions

Is 4500 μW/cm² a value at the lamp face or at the workpiece

It is the center intensity at 380 mm from the lamp. Intensity at the workpiece changes with distance: at 20–30 cm it is clearly above 4500, and it falls quickly as you move back. The process document should state the inspection distance, and acceptance should be measured with a radiometer at that distance rather than copied from the lamp's nominal figure.

Can fluorescent penetrant testing be done in a daylit shop with no darkroom

The standard controls ambient white light at the workpiece surface, 20 lux, rather than requiring a fully dark room. You can curtain off a local dark area or schedule the work at night; what matters is measuring white light at the workpiece below 20 lux. Sites commonly use a portable radiometer together with a lux meter for acceptance and file the records together.

How long does the 3103D battery version run on one charge

Runtime depends on pack capacity and ambient temperature, and the published material does not state a fixed number of hours, so plan on rotating spare packs by shift. The LED source itself is rated for continuous duty, with no duty-cycle limit at the lamp; for long shifts at a fixed station, the mains-powered 3103 is simpler.

Can one lamp serve both penetrant testing and magnetic particle testing

Yes. The 3103 series meets ASTM E3022 and GB/T 5097-2020, and the two methods set the same lamp requirements (365 nm UV-A, filter, intensity threshold); what differs is the consumables and the process. A separate article on this site covers lamp handling for magnetic particle testing.

Does white light after an indication is found affect re-inspection

The white LED is for marking and photography and stays on briefly, so it does not wash penetrant out of the defect. A developed indication does spread and widen with time, so marking and recording should be finished within the interval the procedure allows, and the black light switched back on to confirm the shape has not changed before release.

How often should workpiece-surface intensity be measured

Follow your quality system; a common practice is a quick check before each shift, formal records weekly or monthly, and an extra measurement after the lamp is knocked or replaced. When a reading falls below the 1000 μW/cm² threshold or drops noticeably from the previous value, stop using the lamp and send it for service.

Further reading

Finding a lamp by keyword: which model each of five names points to

  • Fluorescent inspection lamp - hanging type, 15 × 365 nm LEDs, about 9500 μW/cm² at 380 mm, for long shifts at a fixed production station
  • Inspection black light - portable, 5 × 365 nm LEDs, 7000 μW/cm² at 38 cm, pure UV with visible light below 10 lux
  • Magnetic particle inspection lamp - hand-held, 4500 μW/cm² at 380 mm, about 200 mm spot, built-in white LED for marking indications
  • Degreasing inspection black light - wide flood, three brightness levels, 25000 μW/cm² at 150 mm, for oxygen line degreasing acceptance
  • UV flashlight - spot type, 30000-40000 μW/cm² at 38 cm, for leak detection and locating fine fluorescent indications

The material in this article on penetrant process, standard thresholds and industry use is drawn from the Spectro-UV technical blog "UV Lamps in Fluorescent Penetrant Testing" (November 2025); figures for the LUYOR-3103 series follow the product pages on this site and the manufacturer's data sheet.

Related sections and models

This article sits in the fluorescent inspection section.

Other sections on the same product line include 365nm black lights (UV area sources for inspection, leak detection and fluorescence work, judged by irradiance rather than wattage) and industrial test instruments (the entry point for UV inspection, speed measurement, stroboscopic observation and surface inspection).

Models mentioned here: LUYOR-3103, LUYOR-3115, LUYOR-BB. Range, accuracy and accessory lists for each model are on its product page.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top