Xinysun Instrument (Shanghai) Co., Ltd.

Applications

Breadcrumb: Home > Applications > Lab Research

UCL-3500M Application: 302nm UVB Quantitative Irradiation for Studying Skin Photodamage and DNA Repair

Updated:2026-11-02Views:

Studying how ultraviolet light damages skin starts with a UVB source whose dose can be stated precisely. A 2025 study in Frontiers in Pharmacology used a 302 nm UCL-3500M crosslinker as the irradiation source and assessed combined retinol and retinyl palmitate for their repair of UVB-induced DNA damage in HaCaT keratinocytes and reconstructed human epidermis. This article reconstructs the experimental design and the three dose-control points behind it: 50 mJ/cm² calibrated below the culture medium, energy-mode dosing instead of time, and consistent positioning that acknowledges the edge effect. It also summarizes the endpoints the study read and the dose of 120 mJ/cm² used for the 3D model.

Studying how ultraviolet light damages skin starts with a UVB source whose dose can be stated precisely. In a study published in April 2025 in Frontiers in Pharmacology (Zhong et al.), a 302 nm UCL-3500M UV crosslinker served as the UVB source, and the combined effect of retinol (ROL) and retinyl palmitate (RPalm) on UVB-induced DNA damage was systematically assessed in HaCaT keratinocytes and a reconstructed human epidermis model, with the mechanism traced to the homologous recombination repair pathway. This article reconstructs the irradiation protocol and dose-control method of that study from the angle of instrument application.

1. Why this study chose a 302 nm UV crosslinker

Ultraviolet is divided by wavelength into UVC (100-290 nm), UVB (290-320 nm) and UVA (320-400 nm). About 95% of the ultraviolet reaching the ground is UVA and UVB accounts for about 5%, yet DNA absorbs UVB roughly ten times as efficiently as UVA (Budden and Bowden, 2013); 200-800 mJ/cm² of UVB produces significant damage within 4 hours, while UVA needs 10-20 J/cm² and single-strand breaks appear later, at 24 hours (Svobodová et al., 2012). The main lesions caused by UVB are cyclobutane pyrimidine dimers (CPD) and 6-4 photoproducts - abnormal links between adjacent pyrimidine bases that, if not repaired in time, bear directly on DNA replication and transcription.

UCL-3500M is the 302 nm (UVB) version of the UCL-3500 series: within the same series, UCL-3500 is 254 nm and UCL-3500L is 365 nm, and the three share the same lamp configuration, chamber structure and control logic - 6×15 W ultraviolet lamps and an internal chamber of 44×34×15 cm. The 302 nm version was chosen for this kind of work because of two capabilities the crosslinker has by design:

  • Energy-mode control: the dose is set in J/cm² (range 0.000-9.999 J/cm²) and monitored in real time by a UV sensor, so a low dose such as 50 mJ/cm² stays well inside the range and is reproducible from batch to batch;
  • 9 preset programs: a validated dose can be stored as a preset and recalled with one key at power-up, avoiding manual entry errors; start-up takes under 1 second, and timing begins when the lamp actually lights.

In other words, the crosslinker here is not doing "illumination" but "metered dosing" - replacing "how many seconds it was exposed" with "how many J/cm² it received".

2. The experimental design in the paper

The subject was the spontaneously immortalized human keratinocyte line HaCaT (EK-Bioscience, CC-H1149), cultured in DMEM with 10% fetal bovine serum and 1% penicillin-streptomycin at 37 ℃ and 5% CO₂. Irradiation and dosing were designed as follows:

  • Source: UCL-3500M 302 nm UV crosslinker;
  • Exposure geometry: throughout irradiation the cells remained covered by culture medium, rather than being exposed dry in the gas phase;
  • Actual dose: 50 mJ/cm², calibrated in place with a UV radiometer (Speedre SDR-297) placed below the culture medium - the paper records this explicitly;
  • Dosing: retinol 15μM + retinyl palmitate 30μM (dissolved in DMSO), added after UVB exposure so as to avoid photodegradation of retinol;
  • 3D model validation: separately, SkinEthic™ reconstructed human epidermis (RHE, EPISKIN) was cultured at the air-liquid interface for 24 hours, then submerged in medium and irradiated at a UVB dose of 120 mJ/cm² (that section of the paper does not repeat the instrument model; within the same study system it is read as the same UVB source).

Readouts covered inflammatory cytokines (IL-6, IL-8, TNF-α), collagens (COL-1, COL-3), hyaluronic acid synthases (HAS1/2/3, CD44), apoptosis (flow cytometry), DNA damage (γ-H2AX, HMGB1, comet assay, immunofluorescence foci), the cell cycle, and bulk mRNA sequencing together with repair-pathway gene expression.

3. Three keys to dose control

1. Meter below the medium, not at the lamp face

Culture medium attenuates UVB noticeably, so cells below the surface receive less than the nominal value of the chamber. The approach in this study was to put the radiometer probe below the medium at the same position as the samples, read there, and work back from that reading to the irradiation setting. Skip this step and the "50 mJ/cm²" of the whole experiment is no more than a wished-for number.

2. Use energy mode, not time mode

Lamps age and their output falls, mains fluctuation changes output, and a protocol written as "irradiate for N seconds" has limited batch-to-batch reproducibility. Energy mode integrates the actual reading of the UV sensor and stops when the set dose is reached, taking the difference in lamp condition out of the experimental variables.

3. Keep positioning consistent and face the edge effect

The internal chamber of UCL-3500 measures 44×34×15 cm, comfortable for several plates at once, but a larger chamber makes the irradiance difference between center and edge more obvious - what energy mode guarantees is the dose at the sensor, not the same dose at every position. The practice in the paper (samples grouped, same position within a batch) is the standard answer: keep multi-plate samples as close to the center as possible, hold the same position across batches, and state the positioning rule in the methods. The UCL-3500 product page describes in more detail how the aluminum chamber, aluminum diffuser plate and sensor position (above the chamber, with a quartz protective cover) narrow the uniformity difference.

In addition, supplementary experiments fixed 50 mJ/cm² as the "effective photodamage dose": at this dose the damage markers rise consistently, while the 0.1% DMSO vehicle control has no effect on cell viability. When moving to a new cell batch or new culture conditions, this dose-finding step is worth repeating.

4. Results at a glance: a reliable dose is what makes conclusions stand

The work began with a dose-response analysis over the 0-60μM range using SynergyFinder+, which fixed the combination of 15μM ROL + 30μM RPalm; that concentration was then evaluated on the 50 mJ/cm² UVB model:

  • Anti-inflammatory effect: the combination brought UVB-induced IL-6 and IL-8 mRNA markedly below the single-agent groups; TNF-α was also lowered, but with no significant difference between the single agents;
  • Matrix and collagen: COL-1 and COL-3 protein expression rose, and gene expression of HAS1, HAS3 and the hyaluronic acid receptor CD44 was promoted; HAS2 did not rise;
  • Apoptosis: flow cytometry showed that the combination significantly reduced UVB-induced apoptosis;
  • DNA damage: γ-H2AX and HMGB1 levels fell significantly; comet tail intensity was clearly reduced in the combination group alone (neither single agent did this); γH2AX foci likewise decreased in the combination group alone; the G2/M arrest caused by UVB was shifted back toward S phase by the combination, which points to enhanced double-strand break repair;
  • Omics and mechanism: bulk mRNA sequencing showed 4,872 differentially expressed genes after UVB, and treatment with the combination enriched p53 and DNA damage repair pathways significantly; phosphorylation of p-ATM, p-CHK2 and p53(Ser15) increased, and both mRNA and protein of the homologous recombination (HR) pathway genes BRCA1 and RAD52 were up-regulated; in the reconstructed human epidermis model, γH2AX foci were reversed in the combination group alone; RARβ expression rose, and adding the RAR antagonist AGN193109 blocked the repair effect - the synergy depends on RAR signaling.

This chain of conclusions is long, but its foundation is a single layer: every group has to receive 50 mJ/cm² of UVB. In an experiment where the dose drifts, every Western blot and sequencing result downstream loses its meaning.

5. Standard operating procedure

A reusable procedure assembled from the methods in the paper:

  1. Pre-treatment: let the cells attach in advance and change to fresh medium before irradiation; keep the samples covered by medium throughout exposure;
  2. Positioning: place samples in the center region of the chamber, keep the same arrangement for multi-plate runs, and record the preset number used;
  3. Calibration: put the radiometer probe below the medium at the same position as the samples and measure the dose rate at that point;
  4. Setting: select energy mode and set the target dose from the calibration result (HaCaT 50 mJ/cm²; RHE 120 mJ/cm²);
  5. Irradiation: record the actual exposure time after start-up, and finish one batch in a single run where possible to reduce within-batch variation;
  6. Post-treatment: give ROL+RPalm after UVB as designed, and culture to the sampling time point of each endpoint.

6. Where else this protocol fits

  • UVB photodamage and photoaging models: low-dose UVB injury in 2D cell lines and 3D reconstructed epidermis alike;
  • In vitro evaluation of sunscreens and functional skincare: a standardized irradiation step for anti-inflammatory and repair endpoints (γ-H2AX, CPD, collagen markers);
  • DNA damage and repair mechanism studies: a dose-controlled UVB source for CPD formation, double-strand break markers and NER/HR pathway intervention experiments;
  • Phototoxicity and photostability testing: repeatable ultraviolet exposure of test articles;
  • UV mutation breeding: such work normally switches to the 254 nm short-wave standard version, UCL-3500; for a case study, see UCL-3200 in UV mutation breeding.

7. Frequently asked questions

What is the difference between UCL-3500M and UCL-3500?

The wavelength. M is 302 nm (UVB), the standard version is 254 nm (UV-C), and UCL-3500L in the same series is 365 nm (UV-A). Lamps (6×15 W), chamber (44×34×15 cm), energy control and preset logic are the same. Choose M for biological UVB exposure, and the standard version for membrane crosslinking or DNA excision from gels.

Why use energy mode instead of time mode?

Lamp aging and mains fluctuation both change the output power per unit time, so a protocol set by time has limited batch-to-batch reproducibility. Energy mode integrates the energy actually received by the UV sensor and stops at the set dose, removing differences in light-source condition from the experimental variables.

Is metering below the medium really necessary?

Yes. Culture medium attenuates UVB, so the actual dose reaching cells below the surface is lower than the nominal chamber value. This study used the radiometer reading below the surface as the basis for the actual dose; skip the calibration and the dose will be systematically overestimated.

What should be watched when using the large chamber?

Face the edge effect: irradiance differs between the center and the edge of the chamber, so samples should be kept as close to the center as possible and each batch should keep the same arrangement. On the equipment side, the aluminum chamber and aluminum diffuser plate narrow the difference, and the sensor sits above the chamber behind a quartz glass cover, which needs protection from contamination and from aging drift.

Is the 302 nm band on the crosslinker the same as the 312 nm often quoted?

Manufacturers label the UVB band slightly differently; in LUYOR technical documentation UCL-3500M is 302 nm, so for purchase and citation the nameplate and factory report govern. Before settling on a band, read the guide to choosing a crosslinker wavelength and match it to the application.

Can it be used for UV mutation breeding?

Mutation breeding generally uses 254 nm short wave (the standard UCL-3500 or UCL-3200), where DNA absorption is strong and mutation efficiency is high; 302 nm is closer to the solar UVB band and suits photodamage and repair biology. The two uses differ, so do not mix them.

Related products and further reading

Conclusion

What this 2025 study offers is less about retinol itself than about method: turning UVB exposure from "switch on for some seconds" into "deliver 50 mJ/cm²", from a reading at the lamp face into a calibration below the medium surface, from arbitrary placement into a fixed center region - and that is what allows conclusions to be pushed to the mechanistic level. A crosslinker with energy integration and sensor monitoring, such as UCL-3500M, is the equipment basis that makes this step solid.

Source: Zhong J, Liang L, Zhao N, Wang J, Shu P. Synergistic effects of retinol and retinyl palmitate in alleviating UVB-induced DNA damage and promoting the homologous recombination repair in keratinocytes. Frontiers in Pharmacology, 2025, 16:1562244. DOI: 10.3389/fphar.2025.1562244 (open access, CC BY 4.0). This article is an original reading of that paper; experimental details follow the original.

Related sections and models

This article belongs to the laboratory research techniques section.

Other sections on the same product line include UV transilluminators (gel and thin-layer chromatography excited from below, so bands can be read without turning the plate over), UV crosslinkers (dose set in J/cm², the number that governs both nucleic acid crosslinking and material curing), and UV irradiation chambers and photochemical reactors (metered exposure of cells, microplates and materials).

Models mentioned in this article: UCL-3500, UCL-3200, LUYOR-3419. Ranges, accuracy and accessory lists for each model are given on the product pages.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top