Xinysun Instrument (Shanghai) Co., Ltd.

Applications

Breadcrumb: Home > Applications > Lab Research

Which UV Lamp Breaks a PC Linker? How Long Should Irradiation Take? - XX-15 Application Q&A

Updated:2026-11-17Views:

Which lamp a photocleavable linker needs, and for how long, has a short answer worth stating first: 302 nm mid-wave or 365 nm long-wave suits the ortho-nitrobenzyl group, and the classic papers used a bench three-wavelength lamp of the XX-15 type. Irradiation runs from about 4 minutes to 30 minutes, set by the irradiance reaching the sample, the linker type and the sample form - in solution, on a solid support, or still on CPG. The note explains why 254 nm short-wave is not advised, since it induces thymine dimers, and works through the factors that stretch the time: distance, vessel material, sample form, and linker type with pH.

A PC linker (photocleavable linker) is a class of ortho-nitrobenzyl linking group, widely used for photocleavable biotin, light-controlled release tags and the affinity purification of synthetic oligonucleotides. "Which lamp, and for how long" are the two questions asked most often about this experiment. The answer up front: a 302 nm mid-wave or 365 nm long-wave UV lamp suits it - the classic literature used a bench three-wavelength lamp of the XX-15 type - and irradiation time runs from about 4 minutes to 30 minutes, set jointly by the irradiance of the lamp, the linker type and the sample form.

Which UV band does a PC linker need?

The absorption of ortho-nitrobenzyl PC groups falls in the near-UV (300-365 nm), and both lamp types have solid support:

  • 302 nm mid-wave (the classic choice): in the 1996 study on photocleavable biotin published in Nucleic Acids Research, the authors used a benchtop XX-15 UV lamp (the model's original designation, now part of the LUYOR line) and irradiated at 300-350 nm, releasing oligonucleotides quantitatively from a streptavidin solid phase in about 4 minutes;
  • 365 nm long-wave (equally common): reagent suppliers' synthesis guides state that oligonucleotides in 0.1 M TEAA, irradiated with a handheld source at about 365 nm and 1 mW/cm², reach quantitative cleavage of PC Biotin, PC Amino and PC Spacer in about 10 minutes.

The XX-15 laboratory tube UV lamp in our catalogue is a two-tube unit available at 254, 302 or 365 nm; changing the tube covers both photolysis requirements.

How long does irradiation usually take?

Cleavage time is set mainly by the irradiance reaching the sample surface. Reference values from the literature and supplier documentation:

  • 6 W bench lamp at 302 nm (order of 2 mW/cm²): a single-molecule fluorescence microscopy study measured a characteristic cleavage time of about 1.6 minutes, and 5 minutes of cumulative irradiation brought surface-bound molecules down to background level;
  • XX-15 at 300-350 nm: solid-phase release complete in about 4 minutes, with release efficiency above 92%;
  • 365 nm at 1 mW/cm²: quantitative cleavage in about 10 minutes (PC Biotin / PC Amino / PC Spacer);
  • 365 nm at 1-5 mW/cm²: cleavage efficiency above 90% within 5-25 minutes (photocleavable biotin reagent guide);
  • A general-purpose PC Linker (a spacer arm without biotin): cleavage is slower, and up to 30 minutes may be needed even at 25 mW/cm².

In practice, irradiate for 5 minutes, take a sample and check cleavage efficiency by HPLC or a denaturing gel, then top up if needed; that is steadier than running the full time in one go.

Why 254 nm short-wave is not advised

254 nm deep UV will also cleave a PC group, but it induces thymine dimers in nucleic acids and damages the sample directly. Supplier guides state plainly that a stronger deep-UV source needs a 300 nm cut-off filter to protect the DNA. For photolysis, switch the lamp to 302 nm or 365 nm and leave 254 nm alone.

What stretches the cleavage time?

  • Distance: irradiance falls roughly with the inverse square of distance, so the intensity at 25 cm is a quarter of that at 12.5 cm. The XX-15 is rated 1650 μW/cm² at 25 cm; moving closer cuts the time several-fold;
  • Vessel material: ordinary glass and most plastics block 302 nm mid-wave, so use a quartz dish or another UV-transmitting material; 365 nm is more forgiving of the vessel;
  • Sample form: a linker in solution cleaves efficiently; an oligonucleotide still attached to the CPG solid support may photolyse at only 5-10%, so cleave it off the support before irradiating;
  • Linker type and pH: a general-purpose PC Linker cleaves more slowly than PC Biotin, and release of 3'-phosphate oligonucleotides also depends on pH, being higher at pH 9.4 than at pH 7.4.

Procedure notes for photolysis with the XX-15

  1. Confirm the band that suits your linker and set the tube to 302 nm (the usual band for solid-phase release) or 365 nm;
  2. Hold the sample in a quartz dish or UV-transmitting vessel, keep the liquid layer thin, and stay 10-25 cm from the tube;
  3. Switch on and let the output stabilize for about 1 minute before starting the clock;
  4. Irradiate for 5 minutes, sample and verify cleavage efficiency by HPLC or a denaturing gel, then top up if needed;
  5. To convert "how long" into "how much dose" for quantitative control, add a UV radiometer and measure the irradiance at the sample position;
  6. Never look directly at the tube; wear UV-blocking goggles, and keep non-target samples away from light.

Recommended equipment: the XX-15 three-wavelength UV lamp

LUYOR XX-15/XX-20 laboratory tube UV lamp: two-tube construction, available at 254, 302 or 365 nm, the XX-15 rated 2×15 W and 1650 μW/cm² at 25 cm, an aluminium housing that can be hung, and a short-wave tube that can be flipped. PC linker photolysis, gel viewing and cutting, and bench sterilization are all covered by one unit. Users of the XX-15A and other models in the same series follow the same band choice and timing logic as this article.

Frequently asked questions

Which one, 302 nm or 365 nm?

Both bands cleave the ortho-nitrobenzyl group; the difference lies in efficiency and risk. 302 nm has higher photon energy and cleaves fast, releasing quantitatively from a solid phase in about 4 minutes in the literature, but it induces thymine dimers, so it suits short exposures where sample integrity is not critical. 365 nm is gentler and completes cleavage in about 10 minutes at 1 mW/cm², which suits samples that still have to go through enzymatic reactions, ligation or sequencing. If in doubt, start with 365 nm and switch to 302 nm only if efficiency falls short.

How far should the lamp be from the sample?

Irradiance falls roughly with the inverse square of distance, so the intensity at 25 cm is a quarter of that at 12.5 cm. The XX-15 is rated 1650 μW/cm² at 25 cm, and 10-25 cm is the usual working distance. For quantitative work, measure the irradiance at the sample with a UV radiometer and convert "how long" into "how much dose", so the conditions can be reproduced in another laboratory.

Is a quartz dish essential?

302 nm mid-wave is absorbed noticeably by ordinary glass and most plastics, so use a quartz dish, a UV-transmitting petri dish, or an open small-well plate. 365 nm is easier on the vessel and ordinary clear plastic is acceptable for short exposures, but for long exposures move to a UV-transmitting material, otherwise the dose that actually reaches the sample is discounted.

How do I know the linker has cleaved completely?

Sample and run HPLC or a denaturing polyacrylamide gel, then check that the starting-material peak and band have gone and that the released product is present. In practice, irradiate for 5 minutes, sample, and top up for another 5-10 minutes if needed; that is more controllable than running the full time at once. Note as well that an oligonucleotide still on the CPG support photolyses at only 5-10%, so cleave it off first.

How should photolysed samples be stored?

Keep them dark at once: transfer to an amber tube or wrap in aluminium foil so that handling and bench lighting do not expose them again. Release of 3'-phosphate oligonucleotides depends on pH, being higher at pH 9.4 than at pH 7.4, so prepare the buffer for the downstream reaction. Use photolysis products within a short period rather than storing them long term.

Can a handheld LED UV torch replace a bench lamp?

For small volumes over short times it can serve as a stopgap, but a handheld source has unstable irradiance and an uneven spot, so repeatability is poor, and the intensity changes the moment the distance changes, which means the timing cannot be fixed. For quantitative work, batch processing or anything written into a method, a tube lamp such as the XX-15 / XX-15A at a fixed working distance, with a radiometer to record irradiance, is more reliable.

Related categories and models

This article belongs to the frequently asked questions category.

Other categories on the same product line are UV crosslinkers (dose set in J/cm², the figure that matters for both nucleic acid crosslinking and material curing), laboratory UV lamps (single-tube and dual-wavelength bench lamps at 254 / 302 / 365 nm) and life science instruments (the single entry point for fluorescence imaging, UV crosslinking, UV transmission and cell irradiation).

Models mentioned: UCL-3200, UCL-3500, UVP CL-1000. Range, accuracy and accessory lists for each model are given on the product pages.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top