Xinysun Instrument (Shanghai) Co., Ltd.

Solutions

Breadcrumb: Home > Solutions > Speed Measurement

ROS-W/ROS-P and ROLS-W/ROLS-P Tachometer Sensors: Repair and Troubleshooting

Updated:2026-11-17Views:

When a speed sensor fails it rarely goes dark. More often the reading comes and goes, the PLC sees no pulses, or the display jumps. The maintenance window is one or two hours at most, and the engineer on site usually has a multimeter and a screwdriver. Fitting a new sensor is the easy move, yet the new unit often behaves exactly the same, because the fault was never in the sensor. This article separates the W and P variants, maps six field symptoms to their root causes, gives a three-minute bench test, and defines the four wires.

A speed sensor of this kind rarely fails by going dark. More often it reads intermittently, sends no pulses to the PLC, or makes the display numbers jump. The window for a maintenance stop is often no more than one or two hours, and the engineer on site usually has nothing but a multimeter and a screwdriver. Plugging in a new sensor is the convenient route, but it is not rare to find that the new sensor does not work either, because the fault was never in the sensor to begin with.

The four models ROS-W/ROS-P and ROLS-W/ROLS-P share most of their construction: the same 303 stainless steel threaded barrel, the same 1-250 000 rpm range, the same three coloured leads plus shield, and the same pulse for every reflection. The differences sit in two places - whether the light source is an LED or a laser, and whether the cable ends in tinned wires or a 1/8 inch plug. Once those two points are clear, troubleshooting follows one common path.

This article follows the order in which work can actually be done on site: look at the lamp, then measure voltage, then check the wire sequence, then decide whether the sensor is alive, and leave return to factory or replacement to the end.

1. Identify the model: W and P differ in termination alone

Confirm which version you are holding before anything else. The symptoms of W and P are almost identical, but the entry point for troubleshooting is different: on the W version you check the terminal block and the supply inside the cabinet, on the P version you check the plug, the socket and the supply of the instrument it is plugged into.

ModelCable endCable lengthSupplyOutputTypical downstream device
4 tinned wires (brown/blue/black + shield)8 ft (2.4 m)3.0-15 Vdc, approx. 40 mANegative pulse (+V pulled to 0)Terminal block, ACT series panel meters, F2A converter, DataChart
1/8″ (3.5 mm) male plug8 ft (2.4 m)3.0-15 Vdc, supplied by the instrument it is plugged intoNegative pulsePLT200, Nova-Pro 300/500, PLS stroboscopes
4 tinned wires8 ft (2.4 m)3.3-15 Vdc, power consumption ≤0.4 WOpen collector (internal 4 700 Ω pull-up to 3.3 V, load ≤25 mA)Terminal block, PLC input module, data logger, panel meter
ROLS-P (laser)1/8″ male plug8 ft (2.4 m)3.3-15 VdcOpen collectorHandheld tachometer, stroboscope, SPSR-IM power module
ROLS24-W (laser)4 tinned wires8 ft (2.4 m)24 Vdc ±10%Open collectorOn-site 24 Vdc systems, no step-down needed

The optical figures of the four models are worth remembering, because every distance and angle question depends on them: the LED version (ROS) is rated at 0.9 m with a permitted offset angle of 45°; the laser version (ROLS) is rated at 7.6 m with 60°, 650 nm Class 2, maximum output 1 mW, beam divergence below 18 mrad (spot about 4×7 mm at 2 m). Both versions cover 1-250 000 rpm and are rated for −10 to 70 ℃.

The full model and cable-length table, and how to choose W or P by the downstream interface, are covered in more detail on two collection pages: ROS-W/ROS-P optical speed sensors, ROLS-P/ROLS-W laser speed sensors.

2. Six symptoms and the root cause behind each

Classifying what the field calls a failure is more useful than taking the sensor apart. The table is ordered by frequency, and the top three rows account for most real cases.

SymptomUsual root causeCheck before repairFixable on site
No pulses at all at the meter or PLCNo supply, reversed wire order, target outside the field of view, failed sensorGreen lamp flashing → terminal voltage → wire orderThe top three can all be fixed on site
Reading exactly twice the real speed, or another integer multipleMore than one reflective tape on the target, or a second bright reflector passing the beamCount the bright spots per revolutionA single tape is enough
Reading drops in and out, counts occasionally lostDirty or lifting tape, excessive offset angle, distance at the limit, loose terminalWhether the green lamp flashes regularlyCleaning, re-taping or re-aiming
No reading at low speed (below 500 rpm)Tape too wide: the probe is square to the target and the spot covers the whole tape, giving continuous reflectionTape width and aiming angleNarrow tape (about 5 mm), aimed square
Reading low, with error growing as speed risesPulses filtered out downstream, or too long a filter constant on the PLC inputDownstream input filter settingChange the parameter
Still no signal after a new sensor is fittedInsufficient supply capacity in the cabinet, VFD interference on a shared circuit, damaged PLC channelMeasure voltage off-load, try another channelSolvable, but often misdiagnosed as a sensor fault

The table implies one rule: as long as the green lamp is on target, the sensor itself is most likely good, and the problem lies in the tape, the angle, the wiring or the downstream device. The sensor itself becomes the suspect when the green lamp does not flash at all.

3. Start with the green lamp: on-target status is more direct than the reading

Every ROS and ROLS unit has a green On-Target indicator in the cable-end cap. Its meaning is unambiguous: it toggles once for every valid reflection received. At low speed the eye can see it flash in step with rotation; as speed rises the flash rate exceeds persistence of vision and the lamp appears continuously lit.

The lamp is therefore the direct way to tell whether the optical path is working, and much faster than guessing from the meter. Three states, three conclusions:

  • Regular flashing: the optical path is fine, and the fault is electrical (wire order, polarity, downstream input configuration).
  • Continuously lit, or not lit at all: do not conclude yet. Continuously lit means too much light returns and the target is constantly illuminated, usually because the probe is too close or is looking at a mirror surface. Not lit means no light returns at all.
  • Irregular flashing: rule out a dirty or lifting tape, a marginal offset angle and bracket vibration, one at a time.

When the lamp stays dark, work through the four points below in order; in most cases the third one solves it:

  1. Distance: keep the probe at least 1 inch (25 mm) from the target, because closer gives continuous reflection and false triggering. The upper limit depends on the light source: 0.9 m for the LED version, 7.6 m for the laser version.
  2. Angle: the manual suggests about 15° off the target normal, an angle that lets the probe see the tape while avoiding stray reflection from the shaft face and the fixture. The permitted maximum is 45° for the LED version and 60° for the laser version, but usable distance falls quickly as the angle grows.
  3. Tape: the usual choice is a 12 mm square (1/2 inch) T-5 reflective tape on a clean, flat, oil-free rotating surface. Below 500 rpm the rule reverses - aim square (90°) and use a narrow strip about 5 mm wide, so that the reflection is brief enough.
  4. Obstruction of the field of view: guards, oil mist, chips and moisture collecting on the lens or in the beam path all attenuate the return below the threshold. The lens is acrylic, so do not wipe it with acetone or any strong solvent other than alcohol.

One point that is easily overlooked: if the target has keyways, bolt heads, polished or brushed surfaces, the change in reflection as they cross the field of view can be as strong as the tape, and the symptom is one pulse per bolt. On bright metal targets, place the tape on a relatively rough area instead, or mask the interfering zone with matte black paint.

4. Three minutes to prove the sensor is still alive

The sensor is off the machine and there is no spare of the same model on site. How do you confirm whether it is good or bad? The LUYOR manual gives a practical method worth writing on the bench: aim the probe at an older fluorescent lamp and the output should show a square wave at twice the line frequency.

The reason is that a fluorescent tube extinguishes once per half cycle at line frequency: a 60 Hz supply gives 120 Hz flicker, a 50 Hz supply gives 100 Hz. The sensor treats that flicker as one reflection per revolution, so:

  • An oscilloscope should show a 100 Hz or 120 Hz square wave, with an amplitude close to the supply voltage (on ROS it is a negative pulse, pulled from +V to 0).
  • If the probe is connected to a tachometer, the meter should read a steady 6 000 rpm at 50 Hz or 7 200 rpm at 60 Hz.

Two conditions apply. The method needs tubes on a conventional magnetic ballast; the electronic ballasts and LED tubes now in wide use run at tens of kHz and give completely wrong readings, so they cannot be used for this check. The probe also has to be close enough to the tube that the tube fills the field of view.

It also works without an oscilloscope: set a multimeter to DC volts and measure the signal wire against common. While aimed at the tube the voltage swings between two levels (between the high level and 0 on the negative-pulse version, between the internal 3.3 V pull-up and 0 on the open-collector version); when the tube is moved away it returns to the idle level. A swinging reading means the photoelectric stage and the output stage still work; a dead reading sends you on to the supply and the cable.

The value of this bench test is that it separates a failed sensor from a badly installed one. Often the sensor is good and the problem is a new bracket that changed the angle, or tape smeared with oil. Proving the unit alive at the bench before looking for installation faults on site saves an unnecessary return.

5. Wiring check: the four wires and two output traps

In the official manual the W version has four leads: three coloured wires plus a shield. Our product page writes "3 tinned wires (shield included)", meaning three functional wires; the shield is brought out separately for grounding. Do not cut it off as a spare tail, because it serves both as the shield and as the case ground.

Wire colourROS-WROLS-WROLS24-W
BrownSupply + 3.0-15 VdcSupply + 3.3-15 VdcSupply + 24 Vdc ±10%
BlueCommonCommonCommon
BlackSignal (negative pulse +V→0)Signal (open collector)Signal (open collector)
ShieldCase groundCase groundCase ground

Cutting the plug off the P version and wiring it to a terminal block is common practice, but the wire colours differ between the plastic and the metal plug, and this is where miswiring usually starts. On the metal plug the tip is signal (black), the middle band is supply (brown) and the base is common (blue); inside the plastic plug the tip is signal (red), the middle is supply (black) and the base is drain/common. Wiring by the rule of thumb "red is positive, black is negative" reverses supply and signal on a plastic plug.

The second trap is the output type. All ROS versions output a negative pulse: at rest the signal wire sits at the supply voltage and is pulled to 0 once per revolution. ROLS is open collector by default: at rest an internal 4 700 Ω resistor pulls it to 3.3 V, and it is pulled low when conducting, with a load current limit of 25 mA. TTL or negative-pulse versions must be specified when ordering.

The difference between the two outputs at a PLC input is practical:

  • Open collector is a sinking (NPN-style) connection: the PLC input common goes to positive and the input point to the signal wire. If the PLC has sourcing inputs (common at 0 V), an external converter or a different output type is needed.
  • The negative-pulse version is high at rest and low during a pulse. Most PLC high-speed counter inputs accept it, but a low-speed counter module may read the steady high level as a permanently closed signal, so set the module to count on the falling edge.
  • Above 7.6 m of cable, or when the cable shares a trunking with VFD and servo power lines, prefer shielded twisted pair with the shield grounded at one end, and add an interposing relay or opto-isolation where necessary.

Wiring details, how to identify the PLC input type and the terminal numbers of common downstream devices are listed item by item in Laser speed sensor wiring and outputs explained, and are not repeated here.

6. Supply and cable: a lit lamp is not a signal

A flashing green lamp with a dead meter, or pulses far below supply amplitude on a scope, is almost always a supply or cable problem. Measure three points in this order:

  • Voltage at the sensor: measure between the brown and blue wires. ROS must sit within 3.0-15 V and ROLS within 3.3-15 V (24 V ±10% for ROLS24-W). Many 5 V auxiliary supplies in a cabinet sag below 3.5 V under load: the lamp still lights but the output stage can no longer drive the load. ROS draws about 40 mA and ROLS uses no more than 0.4 W, so the load is light, but voltage drop on a shared circuit cannot be ignored.
  • Swing of the signal wire against common: ROS should swing from about +V to 0; the open-collector ROLS from 3.3 V to 0. A swing of just 0.5 V or so means the downstream input impedance is too low or the pull-up is shorted.
  • Continuity and insulation: with the power off, check continuity between the three wires with a multimeter; they should not conduct to each other. Cables fail most often at bends, at conduit entries and where cable ties are pulled tight. The shield should conduct to the case and be insulated from the signal wires.

When the cable is too short, a 25 ft (7.6 m) extension EC-25P (plug to plug) and bulk three-core shielded cable are available. To lengthen a W version, make the joint inside a terminal box and carry the shield through the joint; do not twist wires together inside a cable tray. If pulses are lost after lengthening, look at the shield at the joint.

7. What can be fixed on site and what must go back

The sensor is a single sealed assembly of optics, optoelectronics and analog circuitry, so the boundary of what can be repaired is clear.

FaultFixable on siteAction
Oil, dust or water marks on the lensYesWipe gently with anhydrous ethanol and a lint-free cloth; no acetone or other strong solvents (the lens is acrylic)
Tape aged, lifting or missingYesClean the surface and re-apply T-5; use T-5WP waterproof tape in wet or washdown areas
Loose bracket, shifted angle, loose nutYesRe-aim until the green lamp flashes regularly, then lock with the two M16 (ROS)/M18 (ROLS) lock nuts
Loose terminal, reversed wire order, shield not connectedYesRe-crimp, check against the wire colour table, bond the shield to the cabinet earth
Supply voltage too low, interference on a shared circuitYesUse a dedicated supply, separate the routing, add isolation
Cable jacket damaged, cores intactDependsSeal the damaged section against water; if the damage is at the cable exit it is structural and the unit goes back
Broken core inside the cable (snapped at the exit)NoThe cable exit is potted into the body; no reliable field repair
Laser or LED dark, fogging or mould inside the lensNoSealed optical assembly; return for inspection
Liquid inside the housing, corroded terminalsNoMoisture has entered; return for assessment or replace
Output stage failed (no swing, stuck low or high)NoThe board is potted inside the barrel; return to factory
Systematic reading errorNoPulse counting has no zero drift; a steady error usually comes from the tape or the downstream device, so rule those out before returning

In one sentence: anything you can tighten, wipe or reconnect is handled on site; anything involving the optics, the circuit or the cable exit inside the body goes back. Opening the body is not an option: the 303 stainless barrel is potted and press-fitted at both ends, so opening it scraps the unit and loses its protection.

8. Maintenance: lens, tape, lock nuts and the limits of protection

The environmental limits of these sensors are often overestimated. The ROS manual gives a humidity condition of 80% relative humidity at 31 ℃, falling linearly to 50% at 40 ℃, which means it is not a waterproof unit for continuous spray or high-pressure washing. The stainless barrel resists corrosion, but the cable exit and the end-cap indicator are the weak points.

For permanent outdoor or wet-shop installation the practice is:

  • Place the probe and its wiring under a roof or a shield, or cover the cable exit with a guard, to avoid continuous spray and condensation.
  • In washdown, steam or cutting-fluid areas, change the reflective tape to T-5WP; ordinary T-5 loses adhesion when wet.
  • Put desiccant in the terminal box and turn its cable entries downward so condensate cannot run in along the cable.
  • When washing the machine, do not point a high-pressure gun at the end-cap indicator or the cable exit.

The laser version also has a safety boundary to respect: Class 2, maximum output 1 mW, a brief sweep is not harmful, but do not stare into the beam and do not view the beam path through optical instruments such as binoculars or magnifiers. Switching off before working on the beam path is a simple and effective habit.

Routine checks can be built into the machine maintenance sheet: once a week confirm the green lamp flashes regularly, once a month wipe the lens and the tape, once a quarter re-tighten the lock nuts and check the cable for wear at the conduit entry. Doing these three things lowers the chance of an unplanned stop.

9. The repair process and how to decide between repair and replacement

Once the fault is confirmed to be in the sensor itself and the warranty has expired, the standard route is a factory repair. The LUYOR process is: submit the repair/calibration request online (model, serial number and symptom) → receive an RMA number by email → ship as instructed with the RMA number on the outside of the package → assessment and a formal quotation on arrival → repair or calibration after payment is confirmed → return shipment. Talk to technical support once before shipping: many suspected faults are eliminated at that step.

A few practical details matter. State in the request whether the device has been in contact with hazardous materials (coolant, chemicals, radioactive substances), because that decides whether it can be opened on arrival. Instruments with batteries must be handled to transport rules. A sensor repair does not necessarily include calibration, but if the instrument is inside a quality system and a traceable certificate is required, arrange it at the same time. A traceable calibration (NIST traceable) typically takes 10-15 days, the standard certificate is valid for one year, and a two-year interval can be requested.

When replacement is the better economics:

SituationPreferenceReason
Liquid inside, internal corrosionReplaceAssessment plus repair approaches the cost of a new unit, and reliability is lower afterwards
Cable snapped at the exit, body must be opened to replace itDepends on ageRepairable under two years of service; older units are better replaced
Discontinued model, spares no longer suppliedReplace or upgradeAn equivalent model can take its place, but interface and output must be checked again
Few units in service, high cost of downtimeSpare plus replacementKeep one spare for critical points so production continues while the repair is away
The fault is actually installation or downstreamNo repairWork through sections 4 and 5 before blaming the sensor

Choosing a replacement follows different logic from repair: select for the site conditions rather than settling for the old model. Where ambient light is strong, sunlight falls directly on the target or the lens condenses frequently, consider the frequency-modulated laser model with better light rejection, ROLS-5PW (7 m class, built-in high-frequency filter). For portable inspection a plug version is more flexible; if the signal has to reach a control room, use the LUYOR-912 speed transmitter to convert to 4-20 mA/RS485. Where local display and alarm are enough, the LUYOR-910 panel tachometer connects with three wires. For how to choose by downstream interface, cable length and light source class, see the laser speed sensor selection guide; the section overview is speed sensors.

10. Frequently asked questions

The green lamp flashes but the meter stays at 0. Which part is at fault?

The flashing lamp shows that the optical path is working, so the fault is in the electrical section. Check in turn: is the signal wire on the correct terminal (black is signal), does the polarity match the downstream device, does the input need sinking or sourcing wiring, is a pull-up resistor required, is the PLC channel damaged? The quick test is to connect the sensor to a spare meter of the same model or to an oscilloscope: a reading there means the downstream configuration is at fault.

Why is the speed reading exactly twice the real value?

Two pulses are produced per revolution. The usual cause is two tapes on the target, or one tape split in two by the spot, or a keyway, bolt head or polished surface adding a reflection as it passes. Stop the machine, turn it over by hand and count how many times the green lamp flashes per revolution.

Can the sensor be opened and repaired in house?

Not advisable. The 303 stainless barrel is potted and press-fitted at both ends; opening it removes the sealing and the protection, and the optics and circuit cannot be reset without the proper tooling. Faults inside the body, in the optical assembly, in the output stage or at the cable exit should all go back to the factory.

Without an oscilloscope, how can the sensor be checked quickly?

Set a multimeter to DC volts and measure the signal wire against common, then aim the probe at a fluorescent tube on a magnetic ballast. The voltage should swing between two levels (between the high level and 0 on ROS, between the 3.3 V pull-up and 0 on the open-collector ROLS) and return to the idle level when the tube is moved away. A swing means the photoelectric stage and the output stage are working. Electronic ballasts and LED tubes do not work for this test.

Can a broken cable be extended?

Yes, but the joint must be inside a terminal box, with the shield carried through and grounded at one end. Twisting wires together in a tray and taping them introduces interference and loses pulses. If the break is at the cable exit it is structural damage and the remedy is a factory cable replacement. For longer runs a 25 ft (7.6 m) finished cable and a plug-to-plug extension are available.

24 Vdc is all that is available on site. Can ROLS-W be connected directly?

No. ROLS-W accepts 3.3-15 Vdc and 24 V will damage it. Two options: use ROLS24-W (the 24 Vdc ±10% version), or add a 24 V to 12 V isolated supply module in the cabinet. ROS-W has a 15 V upper limit and likewise cannot be connected to 24 V directly.

The probe is outdoors and loses signal after rain. How can that be prevented?

Start by finding where the water enters: most often at the cable exit and the end-cap indicator, next at the seam between cable jacket and body. Remedies are to move the probe and wiring under a roof, turn the terminal box entries downward and add desiccant, apply secondary sealing at the end cap, and change the tape to a waterproof type. If water has already reached the inside, the unit must go back for assessment.

Does a repaired sensor need recalibration?

A pulse-type speed sensor has no zero drift: it counts pulses and the downstream device converts them, so a functional check is usually enough after optical or output parts are replaced. If, however, the machine is inside a quality system and test reports cite traceable data, a traceable calibration should be performed and the certificate kept; the standard certificate is normally valid for one year.

Resources and service

Related sections and models

This article belongs to the speed and stroboscopic measurement section.

Other sections on the same product line include laser tachometers (aim at reflective tape and read RPM directly, one-handed), industrial test instruments (the entry point for the four lines: UV inspection, speed measurement, stroboscopic observation and surface inspection).

Models mentioned in this article: LUYOR-912, LUYOR-910, LUYOR-925. Ranges, accuracy and accessory lists for each model are listed on the product pages.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top