Xinysun Instrument (Shanghai) Co., Ltd.

Applications

Breadcrumb: Home > Applications > Lab Research

UV Crosslinking of Nanofiber Membranes: Application of the UCL-3200 in Electromagnetic Shielding Material Preparation

Updated:2026-11-02Views:

Flexible electromagnetic shielding films run into a familiar trade-off: however well the filler is dispersed, crosslinking makes the film brittle, and without crosslinking the structure will not hold. This article takes a recent published route and breaks UV radiation crosslinking into a quantitative process - what parameter profile the step needs, why this kind of work has to run in energy mode rather than time mode, and a three-step parameter setup with reference values. It also answers how to choose between 254 and 365nm, why a high-power irradiation chamber is the wrong tool here, and what the delivered dose of 0.06-0.12 J/cm² actually means on a UCL-3200.

Anyone working on flexible electromagnetic shielding films has met this problem: however well the filler is dispersed, crosslinking makes the film brittle; without crosslinking, the structure will not hold. A team recently turned the UV radiation crosslinking of nanofiber films into a quantitative process, and the parameter conversions in this article come from that route.

In a molecular biology laboratory the UV crosslinker is usually known as a membrane-fixing instrument, but in materials work it is a different kind of equipment - a quantitative platform for UV radiation crosslinking and curing . The LUYOR UCL-3200 is a typical example of this class: three selectable wavelengths at 254 nm, 302 nm and 365 nm, an energy mode covering 0.000-9.999 J/cm², a time mode covering 00.00-99.59 min, and a microprocessor that monitors UV output continuously and stops the exposure automatically at the set value. This article looks at how it is used in one specific application, nanofiber film crosslinking.

Start with what the process needs: the parameter profile of the crosslinking step

Take an electromagnetic shielding film built on a PVA-co-PE (polyvinyl alcohol-co-ethylene) nanofiber matrix with UHMWPE (ultra-high molecular weight polyethylene) fiber as the reinforcing skeleton. The usual sequence is: fiber dispersion, mixing with conductive fillers (RGO, Fe₃O₄ and similar), vacuum-assisted filtration into a film, impregnation with crosslinker, UV radiation crosslinking, then air drying.

The last two steps decide the strength and stability of the film. The example parameters recorded in published patent CN119507257B are as follows (check against the patent gazette before citing them):

Process parameterValue
CrosslinkerTrimethylolpropane triacrylate (TMPTA), diluted in ethanol
Crosslinker concentration3 wt% to 5 wt% (5% in the example)
UV irradiance50 μW/cm²
UV crosslinking time20 to 40 min (30 min in the example)
Film formingVacuum-assisted filtration at a vacuum of -0.1 MPa
Mechanical propertiesTensile stress 10 to 12 MPa
Shielding effectivenessX band 35-37 dB; Ku band 33-36 dB; K band 35-38 dB

Convert those parameters into what the instrument delivers, and the accumulated dose the crosslinking step actually supplies is:

Accumulated dose = irradiance × time = 50 μW/cm² × 1800 s ≈ 0.09 J/cm²

Using the range given in the patent, 20-40 min corresponds to 0.06-0.12 J/cm². That order of magnitude deserves a sentence of its own: crosslinking in the 0.1 J/cm² range over 20-40 minutes falls right inside the working range of the UCL-3200 energy mode. The reference dose for Southern and Northern membrane fixing on this instrument is commonly 0.1-0.12 J/cm², almost the same place as this crosslinking dose. That is not a coincidence but the same order of integrated dose, applied to a different reaction.

For the same reason, this kind of process is better served by a UV crosslinker than by a high-power irradiation chamber. For the specific selection judgment, see the note on the LUYOR-3550 UV irradiation chamber.

Why this kind of process needs energy mode

Degree of crosslinking is directly related to dose. Too little dose leaves the crosslinking incomplete, and the film continues to absorb water and swell in later use while its strength falls; too much dose can embrittle the film, yellow it, or even burn through it.

The complication is that UV tube output falls with accumulated operating hours, and contamination in the cavity, ambient temperature and supply fluctuations add their own variation. With time-based control - stop after 30 minutes , for example - the dose a film actually receives under a new tube and an old one can differ by a wide margin, and that difference is invisible in appearance. It usually shows up as a crosslinking degree that drifts from batch to batch over months, with the cause hard to locate.

The UCL-3200 treats dose rather than time as the controlled variable: a built-in UV radiometer, traceable to a CMA/CNAS laboratory - that traceability is normally shown by a factory calibration certificate rather than by legally mandated in-service metrology, so ask for the certificate on delivery and check the calibration date and validity period - and a microprocessor that monitors UV emission continuously and stops the exposure automatically when the preset energy is reached. The intensity drop caused by tube ageing is compensated automatically, so different batches and different days receive a consistent integrated dose.

The optical layout inside the cavity matters as well. The unit uses a stainless steel mirror reflector together with an orange-peel aluminum diffuser to keep intensity uniform across the irradiation chamber, and the UV sensor above the cavity has a quartz glass guard that protects it from crosslinker vapor. Both points matter especially for film samples.

The light source is six 8 W tubes, the cavity measures about 32 × 26 × 15 cm, net weight is about 10 kg, and the unit runs on 230 VAC and sits on a bench without a dedicated room. Note that some channels list an internal cavity of 32 × 30 × 16 cm, a unit weight of 9 kg and 60 W of power; this site follows the manufacturer's official figures, and you should check the manual supplied with the unit before ordering.

How to set the parameters: three steps

Confirm the wavelength first, then continue .

The crosslinking chemistry is set by the crosslinker. Acrylate crosslinkers such as TMPTA respond mainly to 254 nm and 365 nm: 254 nm carries more energy and initiates efficiently, but it also does more photodamage to the sample; 365 nm reacts more gently and is often used for light-sensitive substrates and thicker samples.

The instrument has three matching models: UCL-3200 (254 nm), UCL-3200M (302 nm) and UCL-3200L (365 nm). For light-sensitive substrates such as nanofiber films, it is advisable to start at 365 nm and run a gradient, using 254 nm only once it is confirmed that the sample is not damaged.

Then decide between time mode and energy mode .

Use time mode while exploring conditions, since it is quick to try different exposure durations; once the parameters are fixed and comparative batches begin, switch everything to energy mode. On the panel, the Program key toggles between them - the green lamp indicates energy mode and the red lamp indicates time mode - and after entering a value on the numeric keys, press Enter to confirm.

The instrument has 9 preset programs, and energy values and times can be stored separately. Once the process conditions are settled they can be saved to a preset, and the next batch simply recalls the program number and starts, which reduces manual entry errors.

Then comes sample placement and warm-up .

Lay film samples flat in a single layer and avoid stacking, which would block light; place the sample in the central area of the cavity, where intensity is more stable. The tubes need a few minutes after ignition to reach stable output, so a 5-10 minute warm-up before starting the timer is advisable. This step is often skipped and is one source of batch-to-batch variation.

Reference settings for this application

The table below is derived from published parameters for this class of process and lists settings that can serve as a starting point; run your own preliminary gradient before formal experiments.

ApplicationWavelengthModeReference dose / timeKey point
Film radiation crosslinking365 nmEnergy0.06 to 0.12 J/cm²TMPTA 3-5 wt%, 20-40 min; intensity uniformity directly affects the crosslinking distribution
Curing thick films and dark samples365 nmTimeSet by process (up to 99.59 min)Dark fillers absorb strongly, so the effective dose inside is below the nominal value
Rapid surface curing254 nmTimeTens of secondsHigh energy and fast, so verify thermal damage first
Coating and substrate surface treatment254 nm or 365 nmTimeSet by processWatch adhesion and curing uniformity
Biomolecule crosslinking (protein-nucleic acid)254 nmEnergyStart from a low doseToo much dose destroys protein activity and epitopes; an unirradiated control is essential

The last row deserves a specific warning. It shares the same instrument with film crosslinking, but the parameter logic is the opposite: material crosslinking wants enough dose for complete reaction, while biological crosslinking has to be strictly limited. The eight application scenarios of the UCL-3200 UV crosslinker gives a more detailed breakdown by scenario.

Frequently asked questions

Should I choose 254 nm or 365 nm?

Look at the crosslinker system and at how light-sensitive the sample is. Acrylate crosslinkers can be initiated at either wavelength; 254 nm is more efficient but carries a higher risk of photodamage, while 365 nm is gentler and suits light-sensitive samples such as nanofiber films and PVA substrates. For nanofiber films, start the gradient at 365 nm.

How do energy mode and time mode divide the work?

Time mode is for the exploration stage, to find a suitable exposure duration; energy mode is for formal data collection and batch production. Every batch that has to be compared across runs should come from energy mode, because only energy mode guarantees the same integrated dose from batch to batch.

Why not use a high-power UV irradiation chamber for crosslinking?

The two are positioned quite differently. The LUYOR-3550 UV irradiation chamber addresses irradiation and aging of large areas, high doses and batch samples, with a large cavity, high intensity (UVC up to 8 mW/cm²) and active temperature control at the sample area; a UV crosslinker addresses quantitative crosslinking and curing, with a small cavity, moderate intensity and precise, traceable dose metering. Using an irradiation chamber for quantitative film crosslinking fails on two counts: the intensity is high enough to damage the substrate, and a small sample sits too far from the tubes in a 68 cm cavity, so the dose fluctuates widely.

Can the instrument deliver an irradiance of 50 μW/cm²?

The typical factory intensity of the UCL-3200 is about 3,500-5,500 μW/cm² at 254 nm and about 2,800-3,500 μW/cm² at 365 nm. The 50 μW/cm² recorded in papers and patents is usually a measured value at the film surface rather than the nominal intensity at the tube center. The difference comes from the distance between sample and tube, from an irradiated area much larger than the rated area of the instrument, and from attenuation inside the cavity. When converting, work from the dose actually measured at the sample surface, which is worth keeping in mind when reproducing data.

How is the degree of crosslinking verified?

Common approaches are FTIR tracking of the decrease in the carbon-carbon double bond absorption peak, gel content measurement (dissolving out the uncrosslinked fraction and weighing the residue), and indirect inference from mechanical properties. The instrument does not measure crosslinking degree itself; it only delivers a stable dose, and judging the degree still needs those characterization methods.

How large a sample fits in the instrument?

The internal dimensions are about 32 × 26 × 15 cm, which suits small and medium samples such as films, filter membranes, porous material sheets and sample bottles laid flat with the cap off. Whole rolls of film and large sheets need to be irradiated section by section, with the placement recorded.

What should I watch for in terms of safety?

Do not open the door while the tubes are lit; most models have a door interlock that prevents starting unless the door is fully closed. Radiation at 254 nm causes irreversible damage to skin and cornea, so do not look directly at the tubes during operation. Do not put flammable, explosive or volatile organic solvents inside the chamber. Calibrate on a regular schedule, log the cumulative operating hours of the tubes, and replace them once the rated life is reached.

Related products and further reading

Closing notes

Compressed into one rule: fix the crosslinker and the wavelength first, use energy mode to lock the dose, then verify the loop with a crosslinking degree measurement . In processes such as UV radiation crosslinking of thin films, the value of the equipment is not how high the intensity is, but whether the dose can be stated clearly and repeated accurately. If you need to work out the wavelength configuration, dose and exposure time for a specific system, or to assess whether an existing process condition is viable, contact us.

Related sections and models

This article belongs to the lab research techniques section.

Other sections on the same product line include UV crosslinkers (set the dose in J/cm², the number that governs both nucleic acid crosslinking and material curing), UV irradiation chambers and photochemical reactors (quantitative exposure for cells, microplates and materials), and life science instruments (the entry point for fluorescence imaging, UV crosslinking, UV transmission and cell irradiation).

Models mentioned in this article: UCL-3200, LUYOR-3550, UCL-3500. Ranges, accuracy and accessory lists for each model are listed on the product page.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top