Xinysun Instrument (Shanghai) Co., Ltd.

Applications

Breadcrumb: Home > Applications > Lab Research

How Much Crosslinking Energy Should a UV Crosslinker Use? 254nm Nucleic Acid Membrane Crosslinking Dose Setting Guide

Updated:2026-11-17Views:

A UV crosslinker accepts a dose setting anywhere from 0 to 9.999 J/cm², yet in practice the question is the opposite one: how much energy should this run get? Too little and the nucleic acid binds weakly to the membrane, so hybridisation signal is low; too much and the nucleic acid is damaged, so the signal falls again. This article covers why dose rather than time is the basis, common dose references, the setting range of each model, and the operating points that matter, and it gives reference values such as 120 mJ/cm².

Manuals for UV crosslinkers quote an energy setting range from 0.000 to 9.999 J/cm², but in real use the question is the reverse one: how much energy should this crosslinking run actually get? Too little and the nucleic acid binds weakly to the membrane, so hybridisation signal is low; too much and the nucleic acid is damaged, so the signal falls again. This article sets out four parts - why the basis is dose, common dose references, the setting range of each model, and operating points - with common questions at the end.

One main line to hold on to: the result depends on the UV dose the sample actually receives, not on the irradiation time. That is why models with a UV sensor treat energy mode as a core function.

1. Why the setting is a dose, not a time

A 254 nm UV lamp ages. Between a new tube and one that has run for a year, the same 30 seconds of irradiation can deliver noticeably different doses to the sample, and fluctuations in supply voltage and ambient temperature change the actual output as well. Time mode records how long the lamp was on; energy mode records how much arrived - the latter integrated in real time by the internal UV sensor and stopped automatically once the set dose is reached.

The practical difference is direct: with a time-based protocol, a new tube, a different machine or even an unstable socket can put batch-to-batch results out of step; with a dose-based protocol the dose is a number that can be written into the record and compared across runs. Wherever the result depends on dose - membrane crosslinking, PCR contamination control, UV mutagenesis - energy mode is the sensible choice.

Time mode is not useless either: it is still used to align with the fixed irradiation times in older literature, or where a sterilisation procedure is defined in time. Models that offer both modes are more flexible in practice: the LUYOR UCL-3200, UCL-3500, UVP CL-3000, Spectro-UV XL-1000/XL-1500 and the XEPU-1208/1215 all support them.

2. Common dose references

The table gives commonly used dose figures for a 254 nm UV crosslinker, by experimental purpose. These are widely used reference values; the membrane manufacturer's instructions and your own laboratory's verification take precedence.

PurposeTypical doseNotes
Nucleic acid membrane crosslinking (Northern / Southern, dot blot, nylon membrane)120 mJ/cm² as a starting pointA widely used reference value and the "optimal crosslink" preset on most models; if binding proves insufficient, raise it in small steps rather than jumping high at once
Nitrocellulose (NC) membrane crosslinkingFollow the membrane manufacturer's instructionsBinding on NC works differently from nylon, and some protocols fix by baking; confirm according to membrane type
PCR contamination control (inactivating amplified product in aerosols)Use the instrument preset or the manufacturer's recommended valueThis is a cavity and aerosol inactivation case with a higher dose than membrane crosslinking, so the instrument preset governs
Bacterial and phage inactivationSet from your verification resultsUV resistance varies widely between organisms; run a dose scouting series with an indicator strain before fixing the protocol
UV mutation breeding and strain improvementA 365 nm model, adjusted to the selection pressure365 nm is gentler, so survival and mutation rate have to be balanced, usually by choosing the dose from a survival curve

A note on units: 1 J/cm² = 1,000 mJ/cm² = 1,000,000 μJ/cm². Setting units are not consistent between brands - LUYOR and XEPU use J/cm², the Spectro-UV XL series uses μJ/cm² and the UVP CL-3000 uses mJ/cm² - and a conversion error puts you out by three orders of magnitude, a common early mistake.

Both extremes of dose deserve attention. Too little: the nucleic acid binds weakly, signal is lost during hybridisation washes, and the symptom is "the same samples give weaker signal year after year". Too much: excess short-wave exposure introduces lesions into the bases, which lowers hybridisation signal instead of raising it, and such damage is irreversible. The purpose of crosslinking is to fix, not to irradiate through.

3. Energy setting ranges by model

All seven current models support dose-based crosslinking; they differ in setting range, lamp power and cavity size:

ModelLamps (wavelength)Cavity (cm)Energy setting rangePresets
LUYOR UCL-32006×8W, 254 nm32×26×150.000–9.999 J/cm²9 groups
LUYOR UCL-35006×15W, 254 nm (3500M = 302 nm / 3500L = 365 nm)44×34×150.000–9.999 J/cm²9 groups
UVP CL-3000 UV crosslinker6×8W, three versions 254 / 302 / 365 nm35×27×160.1–9999.9 mJ/cm²-
Spectro-UV XL-10005×8W, 254 nm (312 / 365 nm optional)34.3×17.8×19.1100–999,900 μJ/cm²120,000 μJ/cm² optimal crosslink
Spectro-UV XL-15006×15W, 254 nm (312 / 365 nm optional)46.4×15.9×31.8100–999,900 μJ/cm²120,000 μJ/cm² optimal crosslink
XEPU-12086×8W, 254 nm (302 / 365 nm interchangeable)32×26×150.000–9.999 J (or 0.00–99.99 J)9 groups
XEPU-12156×15W, 254 nm (302 / 365 nm interchangeable)44×34×150.000–9.999 J (or 0.00–99.99 J)9 groups

Three readings of the table. 1. Power decides how long the same dose takes, not how large the dose should be - the 6×15W models cut irradiation time, they do not invite a higher dose. 2. The larger cavities (44×34 cm class) suit several membranes in one batch, but follow the positioning habit described above; a larger cavity does not mean the same dose at every position. 3. The 120,000 μJ/cm² preset on the XL series is exactly the 120 mJ/cm² membrane crosslinking reference, expressed in different units.

4. Operating points and common mistakes

  1. Keep samples in the central area of the cavity. UV intensity is never uniform inside a crosslinker: it is stronger directly under the lamps and weaker towards the edges. Keep the samples from one experiment in the same place, and do not move them between batches.
  2. Record the dose, not just the time. Write "120 mJ/cm²" in the record rather than "30 seconds"; that is what lets the protocol survive a new tube or a new machine.
  3. Do not raise the dose just because the lamps are powerful. Power affects speed; the sample decides the dose.
  4. Stacked membranes shade each other. As the number of membranes in a batch rises, the dose each one receives falls, so re-verify or irradiate in smaller batches.
  5. Check the in-cavity intensity regularly. Spot-check with a UV radiometer or a crosslinking test card; if the time needed for the same dose keeps growing, the lamps are ageing and should be replaced.
  6. Re-scout after a lamp change. New tubes output more, so a protocol set up on old tubes needs reviewing before it is fixed.

Turn these points into a standard operating card and the batch-to-batch variation at this step largely disappears. The remaining selection questions - which wavelength, which of the seven models - are covered in the UV crosslinker wavelength selection guide and the UV crosslinker FAQ.

5. Common questions

What crosslinking energy should I set on a UV crosslinker?

Nucleic acid membrane crosslinking on nylon membranes usually starts at 120 mJ/cm², a widely used reference value and the "optimal crosslink" preset built into most models. The membrane manufacturer's instructions and your own verification take precedence: if binding is insufficient, raise it in small steps rather than jumping high at once, since over-exposure damages the nucleic acid and weakens hybridisation signal.

Why is energy mode more reliable than time mode?

Lamps age, and supply voltage and ambient temperature fluctuate, so the same 30 seconds can deliver noticeably different doses - and nothing shows on the outside. Energy mode integrates in real time from the UV sensor and stops at the set value, which makes the dose a number that can be recorded and compared, and lets a protocol move to a new tube or a new machine.

How do J/cm², mJ/cm² and μJ/cm² convert?

1 J/cm² = 1,000 mJ/cm² = 1,000,000 μJ/cm². LUYOR and XEPU models set the dose in J/cm², the UVP CL-3000 in mJ/cm² and the Spectro-UV XL series in μJ/cm², so confirm the unit before setting; a three-order-of-magnitude slip is a common accident.

Can a higher-power model shorten the crosslinking time?

Yes. A 6×15W model reaches the same dose in about half the time of a 6×8W model, which suits batch work. Power does not change the dose the sample needs, though: heat-sensitive samples should still follow the protocol dose, and a dry run is worth carrying out beforehand to confirm how much the cavity warms up.

How long can a crosslinked membrane be stored?

Once crosslinked the membrane can go straight into hybridisation; if it is not used at once, seal it and keep it in the dark, avoiding repeated freeze-thaw and prolonged UV exposure. Moving into the hybridisation workflow promptly reduces the chance of nucleic acid degradation.

How often should the lamps be changed?

Judge by the in-cavity intensity check rather than by a fixed number of months. A practical rule: change them when the time needed for the usual dose grows noticeably, or when the radiometer reading falls below about 60-70% of a new tube. The XL series manual uses an intensity below 1,500 μW/cm² as the replacement prompt.

6. Related products and further reading

Conclusion

The dose question on a UV crosslinker comes down to one sentence: crosslink by energy, set the dose from the sample, and let the record carry the protocol. 120 mJ/cm² is the common starting point for nylon membranes, and energy mode turns "how long" into "how much", so lamp ageing and mains fluctuation stop affecting batch reproducibility. Writing the dose into the record is the durable asset this step leaves for the experiments that follow.

Related sections and models

This article belongs to the Frequently asked questions section.

Other sections on the same product line include UV crosslinkers (dose set in J/cm², the figure that matters for both nucleic acid crosslinking and material curing), UV radiometers (mW/cm² intensity and J/cm² accumulated energy, which is how a lamp is judged against spec) and Life science instruments (the entry point for fluorescence imaging, UV crosslinking, UV transmission and cell irradiation).

Models mentioned in this article: UCL-3200, UCL-3500, UVP CL-1000. Ranges, accuracy and the accessory list for each model are given on its product page.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top