Xinysun Instrument (Shanghai) Co., Ltd.

Applications

Breadcrumb: Home > Applications > Fluorescent Leak Testing

Complete Guide to Fluorescent Leak Detection Technology: Wavelength, Sensitivity, Tracer Chemistry, and 18 Field Questions

Updated:2026-11-14Views:

Fluorescence leak detection succeeds or fails on a handful of physical quantities: whether the excitation wavelength matches, whether dye concentration sits inside its window, whether irradiance at the read-out distance holds above 1000 µW/cm², and whether enough time has passed. This article works through six layers - spectrum, fluorescence efficiency, sensitivity, tracer chemistry, dosage worked examples, read-out and recheck, cleanliness and safety - and closes with a quick-reference table of 18 field questions that can serve as a parameter sheet before selection and before a job starts. Read-out practice follows ASTM E3022, ISO 3059 and ISO 4406.

Explaining fluorescence leak detection in a complicated way is easy; explaining it clearly has just one route: follow the chain of photon, dye and eye. If any link in that chain fails, the field symptom is the same - no fluorescence, or fluorescence that is not real. This article follows the chain in order, with parameters taken from the LUYOR and Spectroline ranges we supply, which can be checked against the product pages.

1. Spectrum: the difference between 365nm and 395nm is spectral purity, not brightness

Dyes used for fluorescent leak detection have absorption bands concentrated at the long-wave end of UV-A. For the oil-soluble LUYOR-6100, for example, the excitation peak is about 494nm and the emission peak about 535nm; water-based products work the same way, with the carrier as the difference. For efficient excitation the source energy has to land inside the absorption band while not pushing out visible light at the same time - visible light raises background brightness and reduces fluorescence contrast.

Metric365nm professional leak-detection lamp395nm violet flashlight
Spectral positionLong-wave UV-A, main peak 360–370nmClose to the visible violet edge, significant visible component
FilterUV filter that blocks visible light above 400nmMostly unfiltered, or simply tinted
Background brightnessLow; strong fluorescence contrast in a dark environmentHigh; violet light "drowns" weak fluorescence
UsePinpointing seepage, read-out and acceptanceCoarse screening, non-critical situations

So "looks more violet and brighter" does not mean stronger. To judge whether a lamp can be used for leak detection, check three things: whether the main peak is at 365nm, whether it carries a filter, and whether irradiance is up to standard. ASTM E3022 gives measurement methods for the emission peak and visible leakage of LED UV-A lamps, and that convention can be used for comparison; a more practical field measure is irradiance - whether the level at the read-out distance stays reliably above 1000 µW/cm².

2. Fluorescence efficiency: concentration has a window, and beyond it comes quenching

Dye fluorescence intensity is not a monotonic function of concentration. As concentration rises from zero, fluorescence brightens; past a certain point, intermolecular self-absorption and energy transfer take over, fluorescence dims and the color washes out. That is concentration quenching.

In the field this shows up as two opposite misreadings: too little dye gives no glow or a faint one, read as "no leak"; too much makes the whole area pale and bright, so the boundary of the leak is lost, read as "a bad leak". Either way the conclusion is distorted.

  • Oil systems: dose 0.5–2.5 ml per liter of oil (about 500–2500 ppm); use the upper end for small systems and the lower end for large sumps;
  • Water systems: start at 1000:1; pressure testing of containers can go as dilute as 5000:1;
  • Already dosed but the result is poor: do not solve it by "adding a little more" - check for a medium mismatch, insufficient waiting time or inadequate irradiance before anything else.

3. Sensitivity: from leak rate to "visible fluorescence"

The detection limit of the fluorescence method is set by three quantities together: dye concentration in the seepage, the volume that seeps out, and the thickness of the residue left on the surface. A workable rule of thumb is that once the seepage surface accumulates to the microliter level, it can be read under reasonable irradiance. Converted to specific systems:

SystemTypical detectable magnitudeNotes
Refrigeration / air conditioningSlow seepage of a few grams of refrigerant per yearRefrigerant carries PAG/POE oil, and the dye seeps out with the oil and deposits on the leak surface
Hydraulics and lubricationWeeping points that have not yet formed a dropA thin film on the surface is enough to register, weeks before it becomes visible to the eye
Water systemsSlow weeping, damp tracesWater-based tracer seeps out with the water and leaves a fluorescent trace after drying

What needs emphasis is the role of time: the same 0.01 ml/h leak may show nothing after 10 minutes of illumination but be obvious after 8 hours of accumulation. A leak-detection plan therefore has to state how long passes between dosing and read-out, otherwise "found nothing" is just "looked too early".

4. Tracer chemistry: oil-soluble, water-based and the limits of compatibility

Chemically, LUYOR-6100 is a solvent-borne concentrated dye - Solvent Red 175 dissolved in a highly active hydrogenated naphthenic solvent system. That sets three properties: fully miscible with petroleum-based oils, not miscible with water, and able to remain in the system long term without precipitating (flash point above 85℃, not classified as a hazardous or flammable chemical).

DimensionOil-soluble (6100)Water-based (6200/6300)
CarrierSolvent-borne, miscible with mineral oilWater-soluble, miscible with water in any ratio
Media to avoidWater systems, water-containing hydraulic fluids (HFA/HFB and similar)Oil systems, drinking water and product-contact systems
Fluorescent colorYellow-white under UV; the oil takes an orange-red tint in daylight6200 green / 6300 blue
Residue handlingNo flushing needed, stays with the oil; surface residue wiped off with a dedicated cleanerRinses clean with water
Material compatibilityThe solvent carrier carries some swelling risk for certain elastomers; evaluate old seals on a small sample beforehandFriendly to metals and common plastics, though long soaking at high concentration still needs evaluation

Two further boundaries are easily overlooked: 1. do not mix across media - oil-soluble dye added to a water tank is not "slightly effective", it is completely ineffective and contaminates the system; 2. do not use it in food or pharmaceutical contact chains - even water-based products are for industrial water systems and must not enter drinking water or product contact surfaces.

5. Dosage and circulation time: two worked examples

Example one: a hydraulic station. Tank volume 200L, at 0.5–2.5 ml/L the dose is 100–500ml; 250ml in the middle of that range will do. Run the system for 10 minutes after dosing so the dye circulates fully, then illuminate point by point. For a repeat check at fixed points, re-illuminate the same system without topping up.

Example two: a cooling water system. A 3000L body of water at 1000:1 needs about 3L of concentrate - beyond a single bottle, so in practice make up 500ml as a stock solution and inject it zone by zone, or use the economical 6300 route (500ml covers about 3000L) and test in sections. One more rule for water systems: a static system diffuses slowly, so concentration is high near the injection point and low at the far end; allow for the gradient when reading out and sample at several points if needed.

System typeDosingCirculation / penetration timeWhen to read out
Running oil system0.5–2.5 ml/L5–10 minutesCan be checked the same shift
Static oil systemAs above2–3 hoursAn overnight recheck is more reliable
Circulating water systemFrom 1000:1Circulate 30 minutes or moreRead out once circulation is stable
Static water bodyAs above, injected by zoneHours to a dayAllow for the concentration gradient
Container pressure testCan be diluted to 5000:1Hold pressure 30 minutes or moreScan along welds while under pressure

6. Read-out: ambient light, angle and false positives

Read-out conditions can borrow established NDT practice: UV-A irradiance on the read-out surface not below 1000 µW/cm², ambient white light held below 20 lx (ISO 3059 / GB/T 5097). In engineering terms that means three actions: switch off workstation lights, hang a light-blocking screen, and give the eyes 5–10 minutes to dark-adapt.

False positives are the biggest enemy at the read-out stage. Common sources and how to rule them out:

SourceIdentifying featureRuling out
Residue from an earlier checkFixed location, sharp boundary, matches the previous photographWipe clean and re-illuminate; see whether it reappears in the same place
Assembly or rust-preventive oilBroad patches, blurred boundary, unrelated to seam directionClean, run under pressure, and watch whether the seam shows again
Autofluorescence of rubber and plasticThe whole part glows, outline follows the partChange the angle; autofluorescence does not extend along the leak path
Cleaner residueBlue-white haze, widely distributedWipe a second time and look again
Ambient reflectionMoves when the lamp movesMove the lamp; true fluorescence stays where it is

The most effective read-out sequence is three words: wipe, illuminate, look again. A leak point is accepted when seepage reappears at the same spot after wiping and follows the direction of media flow.

7. Cleaning, residue and system cleanliness

Whether a recheck conclusion can be trusted depends on whether old traces were cleaned off properly. Acceptance, service and warranty work should have cleaners on hand: for oil-phase systems a dedicated fluorescent cleaner wipes off surface residue; water-based products rinse clean with water.

Another point often missed is system cleanliness. Leak detection itself can carry external dust into the system (especially with parts opened or fill ports uncovered), and particulate contamination of the oil directly affects wear rate. Comparing cleanliness codes to ISO 4406 before and after shows whether the job introduced new contamination. For hydraulic and servo systems with tight cleanliness requirements, fill ports and cleaning actions should be handled to cleanroom standards.

8. Safety and environmental care

  • UV-A protection: 365nm is UV-A and does not include the UVB/UVC disinfection bands, so normal use is safe; but long, close direct viewing causes eye fatigue and corneal risk, so UV protective glasses are required (LUV-10 and similar fit over prescription glasses), and the lamp head should not be stared at or aimed at faces;
  • Skin contact: avoid prolonged direct contact and wash hands after the job; people with sensitive skin should watch for photosensitivity reactions;
  • Waste disposal: oil-soluble dye lost with the oil falls under waste oil, to be collected as hazardous waste and never discharged to drains; water-based residue is handled under local wastewater rules;
  • Environmental trend: biodegradable, low-toxicity tracers are becoming a new option for oil-based leak detection; the Spectroline WATER-GLO range is filtered to 2 µm and NSF certified, for water and water/glycol systems.

9. Eight common misconceptions

MisconceptionWhy it is wrongCorrect practice
Using a banknote marker or a pet violet flashlight instead of a leak-detection lampNo UV filter, visible light lifts the background and weak fluorescence is swampedA 365nm lamp with a filter and adequate irradiance on the read-out surface
Adding more dye when fluorescence is faintOnce concentration enters the quenching zone, more dye means dimmer, paler resultsOil 0.5–2.5 ml/L; water from 1000:1
Concluding right after a quick sweepSlow seepage accumulates over time; nothing visible in ten minutes does not mean no leakRun 5–10 minutes for the initial check, look again the next day for slow seepage
Reading out under bright workstation lightingAmbient white light directly flattens fluorescence contrastLights off, light blocked, 5–10 minutes of dark adaptation
Putting oil-soluble dye into a water tankImmiscible, completely ineffective and it contaminates the systemMatch the medium, then pick the color
Judging leak rate by fluorescence brightnessBrightness is governed by concentration, residue thickness and irradiance togetherUse weighing, flow or pressure-decay methods for quantitative work
Re-illuminating after a repair without wiping old tracesOld residue is read as "not fixed yet" or "already fixed"Wipe clean, then circulate under pressure, then re-illuminate
Using fluorescence to check compressed airA gas has no liquid medium to carry the dyeUse ultrasound for gas, with flow-rate accounting

One more variable easily overlooked is temperature: at low temperature oil viscosity rises, dye circulates more slowly, and the read-out window has to be stretched; at high temperature the solvent evaporates faster, residue on the surface is thinner and fluorescence fainter, so a shorter read-out distance and higher irradiance are needed. The same instrument working in summer and in winter does not have the same read-out conditions, and that is normal.

10. A quick reference for 18 field questions

#QuestionKey point
1How to choose between 365 and 395365 for pinpointing small leaks; 395 is suited to coarse screening
2Can an ordinary violet flashlight detect leaksNo: no filter, inadequate irradiance, stray light swamps fluorescence
3Must dye and lamp be the same brandNot necessarily, but the absorption band has to match 365nm and irradiance must be adequate
4What is the principleTracer seeps out with the medium and emits visible fluorescence under 365nm excitation
5How small a leak can it findSeepage accumulating to the microliter level on the surface; refrigerant down to a few grams a year
6How soon after dosing can I lookRun 5–10 minutes; static 2–3 hours; slow seepage overnight
7Can it be done in daylightYes, but shade is preferable; blocking light works better than a brighter lamp
8Does any fluorescence mean a new leakNot necessarily; wipe, then illuminate, and see whether it reappears in place
9How is a repair acceptedWipe off old traces, circulate under pressure, re-illuminate with no new fluorescence
10Can the dye stay in the system long termIndustrial-grade dye can, without changing medium performance
11Does the UV lamp harm the eyesLong direct viewing of UV-A carries risk; wear protective glasses throughout
12Is the leak-detection dye toxicSafe when used as specified; avoid ingestion and prolonged skin contact
13Dosed, but no fluorescence appearsWork through medium mismatch, insufficient wait, ambient light, lamp, concentration, obstruction
14What if fluorescence is faintRaise irradiance, darken the background, check concentration and shelf life
15How does it divide work with bubble testing, sniffing and helium mass spectrometryFluorescence locates, sniffing confirms, helium does the limit test
16Which applications suit itAny system with a closed circulating liquid; not suitable for gases
17How is the lamp maintainedKeep the filter free of oil and scratches; avoid deep discharge of the lithium battery
18Is cleaner mandatoryYes for acceptance and recheck; on demand for routine self-checks

11. Sources

Standards and methods (check the original text by number; versions follow the issuing body's current edition)

  • ASTM E3022, Measurement of emission characteristics of LED UV-A lamps used in fluorescent penetrant and magnetic particle testing - the convention for evaluating 365nm peak and visible leakage;
  • ASTM E2297, Guide for use of black lights in penetrant and magnetic particle testing - lamp use, filters and maintenance;
  • ISO 3059, Non-destructive testing - penetrant testing and magnetic particle testing - viewing conditions - UV-A irradiance ≥1000 µW/cm², ambient white light ≤20 lx;
  • GB/T 5097, Non-destructive testing - penetrant testing and magnetic particle testing - viewing conditions - the national standard version of the conditions above;
  • ISO 4406, Hydraulic fluid power - fluids - method for coding the level of contamination by solid particles - cleanliness comparison before and after the job;
  • ISO 8573-1, Compressed air - part 1: contaminants and purity classes - the reference for gas systems (where fluorescence does not apply).

12. Frequently asked questions

Why can a colleague see fluorescence with the same lamp when I cannot?

Check four conditions: read-out distance and irradiance, ambient white light, dark-adaptation time, and whether the dye has actually circulated to that spot. If any one of the four is a grade off, weak fluorescence disappears. Then check whether the lamp-head filter is oily.

Will a water-based tracer contaminate water quality?

Industrial-grade water-based tracer dosed at the recommended ratio is for industrial circulating and cooling water, not for drinking water or product contact surfaces. After the job, drain it on the system's normal water-change cycle; for systems with strict water-quality requirements, confirm acceptability beforehand.

Can fluorescence tell me the size of a leak rate?

Purely semi-quantitative. Brightness is affected by concentration, residue thickness and irradiance together and cannot be converted directly to leak rate. For quantitative work, pair it with weighing, flow or pressure-decay methods.

How soon after dosing can a refrigerant system be checked?

It depends on circulation and operating conditions. With the compressor running and the system circulating under pressure, fluorescence is visible within 30 minutes to a few hours; very slow seepage may need 1–2 days of running. Intermittent leaks have to be retested under the fault condition.

Does the dye affect oil analysis results?

The dye changes oil color, and spectroscopic tests such as infrared or colorimetric methods can be affected after dosing. If oil analysis is due soon, dose after sampling, or record the dosing time for the laboratory's reference.

Should I choose a kit or individual items?

New users or team issue are better served by a kit (6801 oil-based, 6802 water-based green, 6803 water-based blue), with lamp, dye, cleaner and glasses in one order; if you already have a lamp, simply add dye for the medium you use.

Further reading: How to make early leak detection effective: cost accounting, read-out thresholds and inspection routines, How to trace industrial seepage, Leak troubleshooting in paper mill equipment, Preventive maintenance and inspection plans for hydraulic systems.

Related sections and models

This article belongs to the fluorescence leak detection techniques section.

Other sections on the same product line include fluorescent leak detection (add a tracer, then find the leak point with a UV lamp - locate before you dismantle) and industrial test instruments (the entry point for UV inspection, speed measurement, stroboscopic observation and surface inspection).

Models mentioned in this article: LUYOR-6100, LUYOR-6200, LUYOR-6802. Ranges, accuracy and accessory lists for each model are given on the product pages.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top