Breadcrumb: Home > Products > Life Science Instruments > Laboratory UV Lamps

Overview
Replacement Philips DUV-35W UV bulb for Spectroline MAXIMA ML-3500 lamps: 35W, 85V, PX32d, UVA 315-400 nm, 3.8 mm arc, 2000 hours, made in Germany.
When a high-intensity UV inspection lamp dims after long service, the cause is often a bulb at the end of its life rather than a failed unit - fitting this Philips DUV-35W UV bulb puts the lamp back to work. It is a 35 W compact gas discharge bulb made by Philips in Germany: 85 V lamp voltage, PX32d base, an arc length of just 3.8 mm, and output peaking at 365 nm in the UVA band.
Note that this is a consumable for equipment, not a standalone fixture: it must be installed in a sealed professional reflector and operated with a professional electronic ballast and igniter. With matching equipment and the specified replacement procedure, one bulb delivers a steady 2000 hours or more.
| Item | Specification | Notes |
|---|---|---|
| Light source type | MPXL compact gas discharge lamp | UV spectral radiation (UVA) |
| Peak wavelength | 365 nm | UVA band 315-400 nm |
| Rated power | 35 W | Discharge arc length 3.8 mm |
| Lamp voltage | 85 V (±17 V) | Rated current 3.4 A |
| Starting voltage | Up to 25 kV | Electronic ballast and igniter required |
| Base | PX32d | Per IEC 61/1: 7004-111-1 |
| Overall length | 78 mm | Light center distance 26 mm |
| Diameter | 7 mm lamp bead / 4 mm bulb | 9 mm from heat sink tube to filament |
| Weight | 14 g net / 20 g gross | 1 per carton, 24 per case |
| Life | 2000 hours and up | *With the original trigger ballast; the Philips data sheet states 500 h, and actual life can reach 2700 h depending on the ballast |
| Origin | Germany | Made in Germany |
This bulb is a dedicated or compatible consumable for the high-intensity UV inspection lamps listed below. Check the base and lamp voltage before replacing.
| Equipment series | Notes |
|---|---|
| Spectroline MAXIMA ML-3500 series | Ultra-high-intensity UV lamp (black light), accepts the DUV 35W bulb |
Surface crack checks on castings, forgings, welds, and fasteners: the magnetic suspension indication appears clearly under 365 nm excitation, a daily consumable in NDT shops and inspection lines
Checks for surface-breaking defects: penetrant indications are read under UVA light; for reading points on penetrant and magnetic particle work see five common inspection mistakes
Latent prints at a scene, after treatment with fluorescent reagents, are excited and read under short-arc high-intensity UV
UV verification of life jackets and channel markers, and short-range navigation display
Spot irradiation and curing of UV adhesives, as a local light source for dispensing processes
UV light sources for industrial fiber light guides, theatrical fluorescence effects, and similar special uses
A high-pressure gas discharge bulb (MPXL compact discharge lamp), manufactured by Philips and supplied by LUYOR as a consumable for UV inspection equipment: 35 W, 85 V, PX32d base, UVA 315-400 nm with a 365 nm peak, made in Germany. It is not a standalone fixture; it must be installed in a sealed reflector and operated with an electronic ballast and igniter.
The DUV 35W has no fast run-up mode. It can hot-restrike after switch-off, but the ballast must supply enough starting voltage (up to 25 kV) and power. If restarts fail repeatedly, check the ballast and igniter; if the system is healthy and the bulb still will not strike after a long attempt, consider bulb life.
No. Fingerprint oils sinter into the quartz envelope at operating temperature, causing local devitrification and whitening, and shorten life. Wear gloves when replacing; if you touch the bulb, clean it with alcohol and a swab before fitting.
The output is UVA 315-400 nm with a 365 nm peak, matched to the excitation band of the fluorescent materials common in penetrant inspection; once the bulb is installed in the inspection lamp, the filter blocks visible light and passes UV. Do not look directly at a lit bulb; wear professional UV safety glasses when working.
A bulb system (DUV 35W plus a high-intensity inspection lamp) gives high spot intensity and a mature accessory ecosystem, and suits users who already own LUYOR or Spectroline equipment; an LED system needs no ballast and no bulb changes and offers long runtime, which suits new purchases and field work. For a complete-unit comparison see the fluorescent inspection lamp FAQ, and for reading method see how to use a UV inspection lamp correctly.
Send inquiry
Email: info@xinysun.com
Tel: 131-2093-6518
Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai
Copyright 2026 Xinysun Instrument (Shanghai) Co., Ltd. All rights reserved.
ICP:ICP-2026046447
