Xinysun Instrument (Shanghai) Co., Ltd.

Applications

Breadcrumb: Home > Applications > Semiconductor Cleanroom

How to Choose a Particle Detection Light? Roles of 365nm Blacklights and Surface Inspection Lights and a Comparison of Six Devices

Updated:2026-11-17Views:

A particulate detection lamp cannot count particles; counting belongs to the particle counter. What the lamp does is different: it finds contamination that the eye cannot see or has stopped noticing, and it tells you what that contamination is. Shop-floor cases are usually post-PM re-checks, carrier inner-wall inspection and incoming acceptance, where the airborne data pass but the surface is not clean. This article separates the two optical routes - 365nm UV fluorescence for organic residue and grazing high-intensity light for inorganic particles - sets out what each reveals and what it misses, compares six current instruments, and gives five selection criteria plus a scenario quick reference.

The name "particulate detection lamp" suggests it counts particles. It does not - counting belongs to the particle counter - and what the lamp does is something else: it finds contamination the eye cannot see or has stopped noticing, and tells you what that contamination is. The usual shop-floor cases are post-PM re-checks, carrier inner-wall inspection and incoming acceptance, where the airborne data pass but the surface is not clean.

Two optical routes should be separated before anything else, because their division of labor sets the direction of selection:

  • 365nm UV fluorescence route: organic matter emits visible fluorescence under UV excitation - fibers, skin flakes, glove grease, fingerprints and detergent residue are invisible in white light and light up under UV. Typical instruments are blacklights and UV flashlights, including the LUYOR-BBMA;
  • Grazing high-intensity route: inorganic particles such as silicon dust, metal swarf and glass fragments do not fluoresce, and a beam of strong light at a controlled angle makes them scatter and stand out. Typical instruments are yellow-green surface inspection lamps such as the LUYOR-3360G.

The two are not substitutes for each other. UV finds organics, strong light finds inorganics, and missing one route means missed contamination - that is the basic rule of clean-area re-checks. This article runs through the current instruments in that framework, with common questions at the end.

1. What each route can and cannot find

MethodContaminants it findsWhat it misses
365nm UV fluorescence (blacklight / UV flashlight)fibers, skin flakes, glove grease, fingerprints, detergent and water-based residue, some fluorescent tracerssilicon dust, abrasives, metal swarf and glass fragments do not fluoresce
Yellow-green or white grazing light (surface inspection lamp)inorganic particles, scratches, pits, burrs, handprints, water marks and oil filmslow-contrast defects on dark substrates, and morphology reading of soft contamination such as fibers
Particle counterairborne particle concentration and size distribution (quantitative)where surface contamination sits and what it is
Wipe sampling plus laboratory analysisparticle count and ionic residue at specified points (quantitative, traceable)rapid large-area surveys; inefficient where open faces and deep grooves limit access

Chained together they form a complete route: strong light shows whether something is there, UV shows what it is, the counter gives the airborne numbers, and wipe sampling gives quantitative confirmation. Fuller treatment of method selection and interpretation is in the articles on the semiconductor particulate detection topic and the post-PM particle re-check SOP.

2. Six current particulate detection lamps compared

ModelForm and specificationsProtection and cleanroom fitWork it suits
LUYOR-BBMA8 × 365nm LED array with white-light blocking filter; 9000 μW/cm² at 38cm center, 28.5cm effective spot; AC powered, 1.2kgIP68, water-, oil- and penetrant-resistant, washablecontinuous large-area bench work: machine undersides and trenches, oil and coolant environments, re-checks after tool move-in or modification
LUYOR-311515 × 365nm UV-A LEDs; about 9500 μW/cm² at 380mm, illumination area about 250×500mm; white-light leakage below 22lux; IP65suspended mounting, adjustable angle, multiple units can be combinedfixed-station full-surface coverage: fluorescent penetrant and magnetic particle inspection stations, full-face inspection of large parts
LUYOR-365Lmultiple high-power 365nm LEDs; about 6500 μW/cm² at 38cm center, effective area about 200mm; lithium battery, 3-5 hours continuoushandheld body, 0.36kg without batteryleak checking and penetrant inspection on pipe runs, whole units and reactors
MNT-365A365nm fluorescence excitation; smooth one-piece body with no knurling, generates no dust and sheds no particlescan be taken directly into the clean zone without adding contaminationdaily cleanroom rounds, organic contamination checks on carriers and cassettes, tool PM acceptance
LUYOR-2130L3 × high-power 365nm LEDs; 25000 μW/cm² at 150mm from the head; three brightness levels; white light below 15luxhandheld, lithium batteryclose-range spot checks: degreasing acceptance on oxygen piping and valves
LUYOR-3180UV-A LED spot; 365nm, 30000-40000 μW/cm² at 38cm, 30mm beam center; IP65handheld, two batteries and a car chargerhigh-intensity final judgment: confirming trace grease migration, re-checking suspect points

Matching strong-light instruments: the LUYOR-3360G zoom flashlight for inorganic particles, the LUYOR-3318 bench uniform-light lamp for batch inspection at a fixed station, and the LUYOR-3325G yellow-green portable unit for sweeping a full wafer. The trade-offs are covered in the surface inspection lamp buying guide.

3. Five things to check when selecting

  1. Band. 365nm is the main choice for particulate work: strong fluorescence response and effective with most fluorescent indicators. 385nm excites less but leaks less visible light, and suits special cases such as security inks. Fluorescent penetrant and magnetic particle systems follow standards such as ASTM E3022, where 365nm is the mainstream.
  2. Spot size, not just center intensity. Reading requires the whole area to meet the illuminance requirement; a lamp with a high center figure and a small spot covers a small patch per pass and slows continuous work. The 9000 μW/cm² of the BBMA comes with a 28.5cm effective spot, an orientation that balances coverage and contrast.
  3. White-light leakage. Visible white light mixed into the excitation raises the background of the part surface and compresses the brightness difference between fluorescence and background, which makes reading harder. Lamps with low white-light leakage are clearly better on weak residual fluorescence.
  4. Protection rating and cleanroom fit. Equipment taken into a clean zone needs a smooth, unknurled body that neither traps dirt nor sheds particles; machine undersides, trenches, and oil or coolant environments call for IP68 sealing and washdown. Cleaning validation and rinse residue checks are covered in the riboflavin inspection product notes.
  5. Power form. For fixed stations and continuous bench work choose AC-powered units (lit all day, lighter body); for climbing, tank entry and cross-area mobile work choose battery units.

4. Scenario quick reference

Site scenarioRecommended instrumentReason
Post-PM re-check, machine underside and trenchesLUYOR-BBMAIP68 washable, tolerant of oil, 28.5cm spot for continuous sweep
FOUP and wafer carrier inner walls, slotsMNT-365A + LUYOR-3360GUV for fibers, skin flakes and grease; grazing light for particles and scratches in the slots
Daily cleanroom rounds and incoming acceptanceMNT-365Asmooth one-piece body goes straight into the clean zone without shedding
Full-surface fluorescence reading at a fixed stationLUYOR-3115suspended 250×500mm coverage, white-light leakage below 22lux, close to darkroom conditions
Leak checking on piping, reactors and unitsLUYOR-365L200mm illumination area, fast pass over a whole pipe run
Degreasing acceptance on oxygen pipingLUYOR-2130L25000 μW/cm² at 150mm, three brightness levels for close reading
Final judgment on suspect points and trace greaseLUYOR-318030000-40000 μW/cm² at 38cm, high-intensity narrow beam
Inorganic particles and scratchesLUYOR-3360G / LUYOR-3318yellow-green grazing light brings particles and micro-scratches out

5. Frequently asked questions

Can a particulate detection lamp measure particle count?

No. A particulate detection lamp is a fluorescence excitation and visual reading tool; what it outputs is a qualitative conclusion - whether something is there, where it is, and of what type. Particle numbers need a particle counter for airborne concentration and size distribution, and quantitative results at specified points come from wipe sampling sent to a laboratory. The table earlier in this article sets out the division of labor.

Why must both UV and strong light be used?

Because the physical principles differ. Organic contamination such as fibers, skin flakes and grease emits visible fluorescence under 365nm UV, which is what a UV lamp finds; silicon dust, metal swarf and glass fragments do not fluoresce and appear when a strong grazing beam scatters off them. UV alone misses inorganic particles, strong light alone misses organic residue. The accepted clean-area practice is to start with strong light to see whether something is there, then use UV to see what it is, with the order fixed so that records can be built on it.

Why is the LUYOR-BBMA suited to post-PM re-checks?

Three features match the re-check station. 1. IP68 one-piece sealing, resistant to water, oil and penetrants, so machine undersides, trenches and coolant residue can be washed directly; 2. eight LEDs in an array give 9000 μW/cm² at 38cm center over a 28.5cm effective spot, covering a whole area in one pass so reading conditions stay consistent; 3. a white-light blocking filter suppresses visible light and raises the contrast between fluorescence and background, so weak residue still shows. AC power allows all-day operation, which suits continuous bench work.

Can a UV lamp be taken straight into a cleanroom?

It depends on the body. Knurled, threaded or seamed bodies trap dirt and particles and are themselves a contamination source in a clean area. Choose a smooth one-piece body such as the MNT-365A and it can go in safely. Large-spot fixed units such as the BBMA and 3115 are used around tools, in carrier staging areas and at workstations, not in the core clean zone.

Does a blacklight taken into a cleanroom need regular cleaning?

Yes. Oil and dust on the lens noticeably reduce returned light and excitation, so weak residual fluorescence gets missed. Wipe the lamp head with a cleanroom wipe before each use and put it on the check sheet; do it both before and after entering the clean area.

Fluorescence residue never disappears - is the test method wrong?

One case is often misread as a method problem: the residue is not particles but a uniform film left by detergent or water. Uniform faint fluorescence is usually detergent residue rather than particulate contamination, and the response is to review the cleaning and drying steps rather than to keep scrubbing. How to separate the two is set out in the article on checking particle contamination on carrier inner walls.

6. Related products and further reading

In addition, where the object is inorganic particles and micro-scratches on a flat reflective surface (wafer, cover glass, coated part, polished face), a flashlight suits spot re-checks, while continuous large-area sweeping is better served by the LUYOR-3320 parallel-light surface inspection lamp - it sweeps the surface with a parallel beam 8 degrees off vertical, gives 45000-51000 lux at 30cm, can be mounted on a stand at a fixed station, and supports several units in parallel to cover a large panel.

Related sections and models

This article belongs to the frequently asked questions section.

Other sections on the same product line include semiconductor particulate detection (grazing light for location, fluorescence for organics, counting for concentration - three complementary methods), surface inspection lamps (low-angle side light that pulls particles, scratches and fingerprints out of the background) and industrial test instruments (the entry point for UV detection, speed measurement, stroboscopic observation and surface inspection).

Models mentioned in this article: 280 series, 278 series. Ranges, accuracy and accessory lists for each model are listed on the product page.

  • Official WeChat QR code

    Email: info@xinysun.com

  • Tel: 131-2093-6518

  • Address: 1525 Minqiang Road, Bldg 26, Songjiang, Shanghai

Official WeChat QR code Follow

Official WeChat QR code

Contact

131-2093-6518

Top